Project Home
Project Home
Wiki
Wiki
Discussion Forums
Discussions
Project Information
Project Info
Forum Topic - Broadcom Driver for QNX 6.3.0: (7 Items)
   
Broadcom Driver for QNX 6.3.0  
We are using QNX 6.3.0 with no service packs and it seems the Broadcom 57XX network card in our laptop isn't supported. 
 Has there been a driver update for this NIC?

Alternatively, would it be possible to get a 3COM PCMCIA network card to work?

This is the pci -v output for the Broadcom NIC.

Class          = Network (Ethernet)
Vendor ID      = 14e4h, Broadcom Corporation 
Device ID      = 1600h, Unknown Unknown
PCI index      = 0h
Class Codes    = 020000h
Revision ID    = 2h
Bus number     = 4
Device number  = 0
Function num   = 0
Status Reg     = 10h
Command Reg    = 106h
	I/O space access disabled
	Memory space access enabled
	Bus Master enabled
	Special Cycle operations ignored
	Memory Write and Invalidate disabled
	Palette Snooping disabled
	Parity Checking disabled
	Data/Address stepping disabled
	SERR# driver disabled
	Fast back-to-back transactions to different agents enabled
Header type    = 0h Single-function
BIST           = 0h Build-in-self-test not supported
Latency Timer  = 0h
Cache Line Size= 10h un-cacheable
PCI Mem Address = ecef0000h 64bit length 65536 enabled
CardBus CIS Pointer = 7h
Subsystem Vendor ID = 1028h
Subsystem ID        = 1c8h
Max Lat        = 0ns
Min Gnt        = 0ns
PCI Int Pin    = INT A
Interrupt line = 5
CPU Interrupt  = 5h
Capabilities Pointer = 48h
Capability ID        = 1h
Capabilities         = c002h - 64002100h
Capability ID        = 3h
Capabilities         = 0h - 85200080h
Capability ID        = 5h
Capabilities         = 86h - 84cfce0h
Capability ID        = 10h
Capabilities         = 1h - 5040fa2h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 01 50 02 c0 00 21 00 64 
0x50: 03 58 00 00 80 00 20 85 05 d0 86 00 e0 fc 4c 08 
0x60: 05 10 2c 00 06 7e 00 00 00 00 02 60 00 00 00 00 
0x70: 12 12 00 00 20 00 00 00 50 00 00 00 00 00 00 00 
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 fe 10 08 04 
0x90: 21 ba 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0xC0: 00 00 00 00 00 00 00 00 0e 00 00 00 00 00 00 00 
0xD0: 10 00 01 00 a2 0f 04 05 00 20 1b 00 11 5c 03 00 
0xE0: 42 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00 
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 

          Thanks
Re: Broadcom Driver for QNX 6.3.0  
Looking at the 6.3.0 source for the tigon3 driver, this device is supported.
Is there anything logged in sloginfo?


On 10-09-17 1:57 PM, "Mark Dornbush" <community-noreply@qnx.com> wrote:

> We are using QNX 6.3.0 with no service packs and it seems the Broadcom 57XX
> network card in our laptop isn't supported.  Has there been a driver update
> for this NIC?
> 
> Alternatively, would it be possible to get a 3COM PCMCIA network card to work?
> 
> This is the pci -v output for the Broadcom NIC.
> 
> Class          = Network (Ethernet)
> Vendor ID      = 14e4h, Broadcom Corporation
> Device ID      = 1600h, Unknown Unknown
> PCI index      = 0h
> Class Codes    = 020000h
> Revision ID    = 2h
> Bus number     = 4
> Device number  = 0
> Function num   = 0
> Status Reg     = 10h
> Command Reg    = 106h
> I/O space access disabled
> Memory space access enabled
> Bus Master enabled
> Special Cycle operations ignored
> Memory Write and Invalidate disabled
> Palette Snooping disabled
> Parity Checking disabled
> Data/Address stepping disabled
> SERR# driver disabled
> Fast back-to-back transactions to different agents enabled
> Header type    = 0h Single-function
> BIST           = 0h Build-in-self-test not supported
> Latency Timer  = 0h
> Cache Line Size= 10h un-cacheable
> PCI Mem Address = ecef0000h 64bit length 65536 enabled
> CardBus CIS Pointer = 7h
> Subsystem Vendor ID = 1028h
> Subsystem ID        = 1c8h
> Max Lat        = 0ns
> Min Gnt        = 0ns
> PCI Int Pin    = INT A
> Interrupt line = 5
> CPU Interrupt  = 5h
> Capabilities Pointer = 48h
> Capability ID        = 1h
> Capabilities         = c002h - 64002100h
> Capability ID        = 3h
> Capabilities         = 0h - 85200080h
> Capability ID        = 5h
> Capabilities         = 86h - 84cfce0h
> Capability ID        = 10h
> Capabilities         = 1h - 5040fa2h
> Device Dependent Registers:
> 0x40: 00 00 00 00 00 00 00 00 01 50 02 c0 00 21 00 64
> 0x50: 03 58 00 00 80 00 20 85 05 d0 86 00 e0 fc 4c 08
> 0x60: 05 10 2c 00 06 7e 00 00 00 00 02 60 00 00 00 00
> 0x70: 12 12 00 00 20 00 00 00 50 00 00 00 00 00 00 00
> 0x80: 00 00 00 00 00 00 00 00 00 00 00 00 fe 10 08 04
> 0x90: 21 ba 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 0xC0: 00 00 00 00 00 00 00 00 0e 00 00 00 00 00 00 00
> 0xD0: 10 00 01 00 a2 0f 04 05 00 20 1b 00 11 5c 03 00
> 0xE0: 42 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00
> 0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 
>           Thanks
> 
> 
> 
> _______________________________________________
> 
> Networking Drivers
> http://community.qnx.com/sf/go/post67761
> 

-- 
Hugh Brown                      (613) 591-0931 ext. 2209 (voice)
QNX Software Systems Ltd.        (613) 591-3579           (fax)
175 Terence Matthews Cres.       email:  hsbrown@qnx.com
Kanata, Ontario, Canada.
K2M 1W8
 

Re: Broadcom Driver for QNX 6.3.0  
> Looking at the 6.3.0 source for the tigon3 driver, this device is supported.
> Is there anything logged in sloginfo?
> 

After power up there is nothing in the sloginfo for the NIC.

After typing mount -Tio-net -opci=0,vid=0x14E4,did=0x1600 /lib/dll/devn-tigon3.so  this is in the sloginfo:

Sep 20 10:11:00    2    10     0 devn-tigon3: Unable to reset chip.
Sep 20 10:11:00    2    10     0 devn-tigon3: FTQ reset failed!

Sep 20 10:11:01    2    10     0 devn-tigon3: tg3_stop_block timeout! offset = 2c00
Sep 20 10:11:01    2    10     0 devn-tigon3: tg3_stop_block timeout! offset = 2000
Sep 20 10:11:02    2    10     0 devn-tigon3: tg3_stop_block timeout! offset = 3400
Sep 20 10:11:03    2    10     0 devn-tigon3: tg3_stop_block timeout! offset = 2400
Sep 20 10:11:03    2    10     0 devn-tigon3: tg3_stop_block timeout! offset = 2800
Sep 20 10:11:04    2    10     0 devn-tigon3: tg3_stop_block timeout! offset = 3000
Sep 20 10:11:04    2    10     0 devn-tigon3: tg3_stop_block timeout! offset = 1400
Sep 20 10:11:05    2    10     0 devn-tigon3: tg3_stop_block timeout! offset = 1800
Sep 20 10:11:05    2    10     0 devn-tigon3: tg3_stop_block timeout! offset = c00
Sep 20 10:11:06    2    10     0 devn-tigon3: tg3_stop_block timeout! offset = 4800
Sep 20 10:11:07    2    10     0 devn-tigon3: tg3_stop_block timeout! offset = 1000
Sep 20 10:11:07    2    10     0 devn-tigon3: tg3_stop_block timeout! offset = 1c00
Sep 20 10:11:10    2    10     0 devn-tigon3: Unable to reset chip.

Re: Broadcom Driver for QNX 6.3.0  
It looks as though the chip is not responding. Does it work with any other
O/S?


On 10-09-20 10:20 AM, "Mark Dornbush" <community-noreply@qnx.com> wrote:

>> Looking at the 6.3.0 source for the tigon3 driver, this device is supported.
>> Is there anything logged in sloginfo?
>> 
> 
> After power up there is nothing in the sloginfo for the NIC.
> 
> After typing mount -Tio-net -opci=0,vid=0x14E4,did=0x1600
> /lib/dll/devn-tigon3.so  this is in the sloginfo:
> 
> Sep 20 10:11:00    2    10     0 devn-tigon3: Unable to reset chip.
> Sep 20 10:11:00    2    10     0 devn-tigon3: FTQ reset failed!
> 
> Sep 20 10:11:01    2    10     0 devn-tigon3: tg3_stop_block timeout! offset =
> 2c00
> Sep 20 10:11:01    2    10     0 devn-tigon3: tg3_stop_block timeout! offset =
> 2000
> Sep 20 10:11:02    2    10     0 devn-tigon3: tg3_stop_block timeout! offset =
> 3400
> Sep 20 10:11:03    2    10     0 devn-tigon3: tg3_stop_block timeout! offset =
> 2400
> Sep 20 10:11:03    2    10     0 devn-tigon3: tg3_stop_block timeout! offset =
> 2800
> Sep 20 10:11:04    2    10     0 devn-tigon3: tg3_stop_block timeout! offset =
> 3000
> Sep 20 10:11:04    2    10     0 devn-tigon3: tg3_stop_block timeout! offset =
> 1400
> Sep 20 10:11:05    2    10     0 devn-tigon3: tg3_stop_block timeout! offset =
> 1800
> Sep 20 10:11:05    2    10     0 devn-tigon3: tg3_stop_block timeout! offset =
> c00
> Sep 20 10:11:06    2    10     0 devn-tigon3: tg3_stop_block timeout! offset =
> 4800
> Sep 20 10:11:07    2    10     0 devn-tigon3: tg3_stop_block timeout! offset =
> 1000
> Sep 20 10:11:07    2    10     0 devn-tigon3: tg3_stop_block timeout! offset =
> 1c00
> Sep 20 10:11:10    2    10     0 devn-tigon3: Unable to reset chip.
> 
> 
> 
> 
> 
> _______________________________________________
> 
> Networking Drivers
> http://community.qnx.com/sf/go/post67865
> 

-- 
Hugh Brown                      (613) 591-0931 ext. 2209 (voice)
QNX Software Systems Ltd.        (613) 591-3579           (fax)
175 Terence Matthews Cres.       email:  hsbrown@qnx.com
Kanata, Ontario, Canada.
K2M 1W8
 

Re: Broadcom Driver for QNX 6.3.0  
Works fine in Windows XP
Re: Broadcom Driver for QNX 6.3.0  
You will have to contact your sales rep to arrange to get this fixed.



On 10-09-20 11:04 AM, "Mark Dornbush" <community-noreply@qnx.com> wrote:

> Works fine in Windows XP
> 
> 
> 
> _______________________________________________
> 
> Networking Drivers
> http://community.qnx.com/sf/go/post67875
> 

-- 
Hugh Brown                      (613) 591-0931 ext. 2209 (voice)
QNX Software Systems Ltd.        (613) 591-3579           (fax)
175 Terence Matthews Cres.       email:  hsbrown@qnx.com
Kanata, Ontario, Canada.
K2M 1W8
 

Re: Broadcom Driver for QNX 6.3.0  
Thanks