Project Home
Project Home		 Trackers
Trackers		 Documents
Documents		 Wiki
Wiki		 Discussion Forums
Discussions		 Project Information
Project Info
Community/Discussion/QNX Momentics Getting Started/QNX - Beaglebone Black - Unable to set the target in QNX Momentics/List of Posts
Forum Topic - QNX - Beaglebone Black - Unable to set the target in QNX Momentics: (3 Items)
   
Update
Michael Nguyen(deleted)
12/05/2016 9:25 AM
post117245
QNX - Beaglebone Black - Unable to set the target in QNX Momentics   
hi can someone help us with the following research issues, 

we are trying to build and install qnx neutrino into beaglebone black system with the following steps: 

1. download the latest BSP from http://community.qnx.com/sf/wiki/do/viewPage/projects.bsp/wiki/TiAm335Beaglebone 

2.  Build the package and get the image 

3.  Create SD boot card and boot the board following the user guide steps 

we faced following issues: 

3.1.  when we install the driver for USB connection on window 10, the installation was failed 
3.2.  we still tried to boot be board with the sd card and Ethernet cable connection and get the following result: 
 3.2.1 two steady lights come up
 3,2.2 we can see the board ip address in the router and get the ping from reply

however we can not connect ssh/telnet to the above ip address, nor be able to set up the target to that IP address using
 qnx momentics IDE.

Thank you
Doug Schaefer(deleted)
12/05/2016 9:52 AM
post117246
Re: QNX - Beaglebone Black - Unable to set the target in QNX Momentics   
I think at this point, your best bet would be to attach a serial cable to
the console to see what¹s happening. You¹ll be able to see what¹s
happening from the u-boot boot on up and see if there are any error
messages.

Doug.

On 2016-12-05, 9:25 AM, "Michael Nguyen" <community-noreply@qnx.com> wrote:

>hi can someone help us with the following research issues,
>
>we are trying to build and install qnx neutrino into beaglebone black
>system with the following steps:
>
>1. download the latest BSP from
>http://community.qnx.com/sf/wiki/do/viewPage/projects.bsp/wiki/TiAm335Beag
>lebone 
>
>2.  Build the package and get the image
>
>3.  Create SD boot card and boot the board following the user guide steps
>
>we faced following issues:
>
>3.1.  when we install the driver for USB connection on window 10, the
>installation was failed
>3.2.  we still tried to boot be board with the sd card and Ethernet cable
>connection and get the following result:
> 3.2.1 two steady lights come up
> 3,2.2 we can see the board ip address in the router and get the ping
>from reply
>
>however we can not connect ssh/telnet to the above ip address, nor be
>able to set up the target to that IP address using qnx momentics IDE.
>
>Thank you
>
>
>
>
>
>
>_______________________________________________
>
>QNX Momentics Getting Started
>http://community.qnx.com/sf/go/post117245
>To cancel your subscription to this discussion, please e-mail
>momenticsgs-community-unsubscribe@community.qnx.com
Michael Nguyen(deleted)
12/05/2016 5:02 PM
post117249
Re: QNX - Beaglebone Black - Unable to set the target in QNX Momentics   
We tried to use the serial terminal several times but did not get any luck.  We install the serial driver as in attached
 image.  Plugged the board in, power it up. Then we tried to use Putty to connect to it, nothing come up.  We also tried
 to use hyper terminal to connect to it with the same setting, the terminal responsed "Unable to connect to COM7, please
 check your port setting" 

That was why we decided to blindly write to command to uEnv.txt as the alternative solution.  That was how we got a 
little further with the Ethernet IP address with the hope that we can remote access to it or target it from QNX 
Momentics.  But we stuck again :)

Do you have any recommendation or suggestion for us?
Attachment: Image serials setting.PNG 39.47 KB

Return


  A subsidiary of BlackBerry             All content ©2004-2013, QNX Software Systems