|
wang long(deleted)
10/07/2015 10:06 AM
post114602
|
is I211 supported on QNX4 via Net.e1000?
I got Net.e1000: INITIALIZATION ERROR 1 when I used the following command:
Net.e1000 -v -d1539 -l1-I0
Device 1539 - Revision 3
Net.e1000: INITIALIZATION ERROR 1
net_reg failed.
|
|
|
|
|
|
Hugh Brown
|
Re: I211 support for QNX4
|
|
Hugh Brown
10/07/2015 11:06 AM
post114603
|
Re: I211 support for QNX4
Please try the attached driver. You don¹t need to pass the device ID on
the command line.
On 2015/10/7, 10:06 AM, "wang long" <community-noreply@qnx.com> wrote:
>is I211 supported on QNX4 via Net.e1000?
>
>I got Net.e1000: INITIALIZATION ERROR 1 when I used the following command:
>
>Net.e1000 -v -d1539 -l1-I0
>
>Device 1539 - Revision 3
>Net.e1000: INITIALIZATION ERROR 1
>net_reg failed.
>
>
>
>
>_______________________________________________
>
>QNX4 Community Support
>http://community.qnx.com/sf/go/post114602
>To cancel your subscription to this discussion, please e-mail
>qnx4-community-unsubscribe@community.qnx.com
|
|
|
|
|
|
wang long(deleted)
|
Re: I211 support for QNX4
|
|
wang long(deleted)
10/08/2015 6:40 AM
post114606
|
Re: I211 support for QNX4
Thanks, but I still got the errors, should I get a new version for /bin/Net?
Cmd:
Net.e1000 -v -l1-I0
Device 1539 - Revision 3
After fix-ups FlowControl is now = 0
Forcing Speed and Duplex
M88E1000 PSCR: 0x3150
Full Duplex
Forcing 10mb
Unable to establish link!!!
Initializing the Flow Control address, type and timer regs
Masking off all interrupts
NVM work 0x03 is not mapped.
NVM word 0x03 is not mapped.
Masking off all interrupts
NVM word 0x03 is not mapped.
//1/bin/Net terminated (SIGSEGV) at 0015:000003D8
Net.e1000: INITIALIZATION ERROR 3
net_reg failed.
|
|
|
|
|
|
Hugh Brown
|
Re: I211 support for QNX4
|
|
Hugh Brown
10/08/2015 8:39 AM
post114607
|
Re: I211 support for QNX4
I¹ll have to take a look at this when I get a chance. Are you connecting
to a 10Mb network?
On 2015/10/8, 6:40 AM, "wang long" <community-noreply@qnx.com> wrote:
>Thanks, but I still got the errors, should I get a new version for
>/bin/Net?
>
>Cmd:
>Net.e1000 -v -l1-I0
>
>Device 1539 - Revision 3
>After fix-ups FlowControl is now = 0
>Forcing Speed and Duplex
>
>M88E1000 PSCR: 0x3150
>Full Duplex
>
>Forcing 10mb
>
>Unable to establish link!!!
>
>Initializing the Flow Control address, type and timer regs
>
>Masking off all interrupts
>
>NVM work 0x03 is not mapped.
>NVM word 0x03 is not mapped.
>Masking off all interrupts
>
>NVM word 0x03 is not mapped.
>
>//1/bin/Net terminated (SIGSEGV) at 0015:000003D8
>Net.e1000: INITIALIZATION ERROR 3
>net_reg failed.
>
>
>
>_______________________________________________
>
>QNX4 Community Support
>http://community.qnx.com/sf/go/post114606
>To cancel your subscription to this discussion, please e-mail
>qnx4-community-unsubscribe@community.qnx.com
|
|
|
|
|
|
wang long(deleted)
|
Re: I211 support for QNX4
|
|
wang long(deleted)
10/08/2015 8:45 AM
post114608
|
Re: I211 support for QNX4
I have 6 I211 ports, but only one of them is connected to a 100M network,
I tried for each port, they all got same output.
the Net was got from the QNX 4 Product Suite CD 2015 EXPERIMENTAL,
and the Net.e1000 is the attched driver. I'm not clear if they are matched.
> I¹ll have to take a look at this when I get a chance. Are you connecting
> to a 10Mb network?
>
>
|
|
|
|
|
|
Hugh Brown
|
Re: I211 support for QNX4
|
|
Hugh Brown
10/08/2015 10:55 AM
post114610
|
Re: I211 support for QNX4
Are the I211 adapters on PCIe boards? If so, could you please give me the
Intel name of the adapter?
Thanks, Hugh.
On 2015/10/8, 8:45 AM, "wang long" <community-noreply@qnx.com> wrote:
>I have 6 I211 ports, but only one of them is connected to a 100M network,
>I tried for each port, they all got same output.
>
>the Net was got from the QNX 4 Product Suite CD 2015 EXPERIMENTAL,
>and the Net.e1000 is the attched driver. I'm not clear if they are
>matched.
>
>> I¹ll have to take a look at this when I get a chance. Are you connecting
>> to a 10Mb network?
>>
>>
>
>
>
>
>
>
>_______________________________________________
>
>QNX4 Community Support
>http://community.qnx.com/sf/go/post114608
>To cancel your subscription to this discussion, please e-mail
>qnx4-community-unsubscribe@community.qnx.com
|
|
|
|
|
|
wang long(deleted)
|
Re: I211 support for QNX4
|
|
wang long(deleted)
10/08/2015 6:05 PM
post114613
|
Re: I211 support for QNX4
All the I211 ports are located on a single customized motherboard, I think they are just like the
prototype provided by intel.
the functionalities of the ports have been validated under Windows7 and Linux.
please let me know if you want anything in detail.
> Are the I211 adapters on PCIe boards? If so, could you please give me the
> Intel name of the adapter?
> a
> Thanks, Hugh.
>
>
>
>
> On 2015/10/8, 8:45 AM, "wang long" <community-noreply@qnx.com> wrote:
>
> >I have 6 I211 ports, but only one of them is connected to a 100M network,
> >I tried for each port, they all got same output.
> >
> >the Net was got from the QNX 4 Product Suite CD 2015 EXPERIMENTAL,
> >and the Net.e1000 is the attched driver. I'm not clear if they are
> >matched.
> >
> >> I¹ll have to take a look at this when I get a chance. Are you connecting
> >> to a 10Mb network?
> >>
> >>
> >
> >
> >
> >
> >
> >
> >_______________________________________________
> >
> >QNX4 Community Support
> >http://community.qnx.com/sf/go/post114608
> >To cancel your subscription to this discussion, please e-mail
> >qnx4-community-unsubscribe@community.qnx.com
>
|
|
|
|
|
|
Hugh Brown
|
Re: I211 support for QNX4
|
|
Hugh Brown
10/09/2015 2:00 PM
post114618
|
Re: I211 support for QNX4
Please try the attached driver and let me know if it works.
Thanks, Hugh.
On 2015/10/8, 6:05 PM, "wang long" <community-noreply@qnx.com> wrote:
>All the I211 ports are located on a single customized motherboard, I
>think they are just like the
>prototype provided by intel.
>the functionalities of the ports have been validated under Windows7 and
>Linux.
>
>please let me know if you want anything in detail.
>
>> Are the I211 adapters on PCIe boards? If so, could you please give me
>>the
>> Intel name of the adapter?
>> a
>> Thanks, Hugh.
>>
>>
>>
>>
>> On 2015/10/8, 8:45 AM, "wang long" <community-noreply@qnx.com> wrote:
>>
>> >I have 6 I211 ports, but only one of them is connected to a 100M
>>network,
>> >I tried for each port, they all got same output.
>> >
>> >the Net was got from the QNX 4 Product Suite CD 2015 EXPERIMENTAL,
>> >and the Net.e1000 is the attched driver. I'm not clear if they are
>> >matched.
>> >
>> >> I¹ll have to take a look at this when I get a chance. Are you
>>connecting
>> >> to a 10Mb network?
>> >>
>> >>
>> >
>> >
>> >
>> >
>> >
>> >
>> >_______________________________________________
>> >
>> >QNX4 Community Support
>> >http://community.qnx.com/sf/go/post114608
>> >To cancel your subscription to this discussion, please e-mail
>> >qnx4-community-unsubscribe@community.qnx.com
>>
>
>
>
>
>
>
>_______________________________________________
>
>QNX4 Community Support
>http://community.qnx.com/sf/go/post114613
>To cancel your subscription to this discussion, please e-mail
>qnx4-community-unsubscribe@community.qnx.com
|
|
|
|
|
|
wang long(deleted)
|
Re: I211 support for QNX4
|
|
wang long(deleted)
10/09/2015 10:44 PM
post114619
|
Re: I211 support for QNX4
It reported the same error as previous revision:
the last line indicted this caused the memory fault of Net
%1 80 Memory fault Net -d6
any other hidden options can expose more debug information?
> Please try the attached driver and let me know if it works.
>
> Thanks, Hugh.
>
>
>
> On 2015/10/8, 6:05 PM, "wang long" <community-noreply@qnx.com> wrote:
>
> >All the I211 ports are located on a single customized motherboard, I
> >think they are just like the
> >prototype provided by intel.
> >the functionalities of the ports have been validated under Windows7 and
> >Linux.
> >
> >please let me know if you want anything in detail.
> >
> >> Are the I211 adapters on PCIe boards? If so, could you please give me
> >>the
> >> Intel name of the adapter?
> >> a
> >> Thanks, Hugh.
> >>
> >>
> >>
> >>
> >> On 2015/10/8, 8:45 AM, "wang long" <community-noreply@qnx.com> wrote:
> >>
> >> >I have 6 I211 ports, but only one of them is connected to a 100M
> >>network,
> >> >I tried for each port, they all got same output.
> >> >
> >> >the Net was got from the QNX 4 Product Suite CD 2015 EXPERIMENTAL,
> >> >and the Net.e1000 is the attched driver. I'm not clear if they are
> >> >matched.
> >> >
> >> >> I¹ll have to take a look at this when I get a chance. Are you
> >>connecting
> >> >> to a 10Mb network?
> >> >>
> >> >>
> >> >
> >> >
> >> >
> >> >
> >> >
> >> >
> >> >_______________________________________________
> >> >
> >> >QNX4 Community Support
> >> >http://community.qnx.com/sf/go/post114608
> >> >To cancel your subscription to this discussion, please e-mail
> >> >qnx4-community-unsubscribe@community.qnx.com
> >>
> >
> >
> >
> >
> >
> >
> >_______________________________________________
> >
> >QNX4 Community Support
> >http://community.qnx.com/sf/go/post114613
> >To cancel your subscription to this discussion, please e-mail
> >qnx4-community-unsubscribe@community.qnx.com
>
|
|
|
|
|
|
wang long(deleted)
|
Re: I211 support for QNX4
|
|
wang long(deleted)
10/10/2015 1:36 AM
post114620
|
Re: I211 support for QNX4
Upload the picture of the failure.
> It reported the same error as previous revision:
> the last line indicted this caused the memory fault of Net
>
> %1 80 Memory fault Net -d6
>
> any other hidden options can expose more debug information?
>
> > Please try the attached driver and let me know if it works.
> >
> > Thanks, Hugh.
> >
> >
> >
> > On 2015/10/8, 6:05 PM, "wang long" <community-noreply@qnx.com> wrote:
> >
> > >All the I211 ports are located on a single customized motherboard, I
> > >think they are just like the
> > >prototype provided by intel.
> > >the functionalities of the ports have been validated under Windows7 and
> > >Linux.
> > >
> > >please let me know if you want anything in detail.
> > >
> > >> Are the I211 adapters on PCIe boards? If so, could you please give me
> > >>the
> > >> Intel name of the adapter?
> > >> a
> > >> Thanks, Hugh.
> > >>
> > >>
> > >>
> > >>
> > >> On 2015/10/8, 8:45 AM, "wang long" <community-noreply@qnx.com> wrote:
> > >>
> > >> >I have 6 I211 ports, but only one of them is connected to a 100M
> > >>network,
> > >> >I tried for each port, they all got same output.
> > >> >
> > >> >the Net was got from the QNX 4 Product Suite CD 2015 EXPERIMENTAL,
> > >> >and the Net.e1000 is the attched driver. I'm not clear if they are
> > >> >matched.
> > >> >
> > >> >> I¹ll have to take a look at this when I get a chance. Are you
> > >>connecting
> > >> >> to a 10Mb network?
> > >> >>
> > >> >>
> > >> >
> > >> >
> > >> >
> > >> >
> > >> >
> > >> >
> > >> >_______________________________________________
> > >> >
> > >> >QNX4 Community Support
> > >> >http://community.qnx.com/sf/go/post114608
> > >> >To cancel your subscription to this discussion, please e-mail
> > >> >qnx4-community-unsubscribe@community.qnx.com
> > >>
> > >
> > >
> > >
> > >
> > >
> > >
> > >_______________________________________________
> > >
> > >QNX4 Community Support
> > >http://community.qnx.com/sf/go/post114613
> > >To cancel your subscription to this discussion, please e-mail
> > >qnx4-community-unsubscribe@community.qnx.com
> >
>
>
|
|
|
|
|
|
wang long(deleted)
|
Re: I211 support for QNX4
|
|
wang long(deleted)
10/10/2015 3:01 AM
post114622
|
Re: I211 support for QNX4
more details found with -vvv (curious, I can't use console redirection to save all the log to files, but other app can,
so I have to type the last screen to you, any suggestion?)
e1000_check_alt_mac_addr_generic
e1000_read_invm_i210
NVM word 0x03 is not mapped
e1000_read_mac_addr_82575
e1000_check_alt_mac_addr_generic
e1000_read_invm_i210
NVM word 0x03 is not mapped
e1000_reset_hw_82580
e1000_disable_pcie_master_generic
Masking off all interrupts
e1000_ge_auto_rd_done_generic
e1000_reset_mdicnfg_82580
e1000_check_alt_mac_addr_generic
e1000_read_invm_i210
NVM word 0x03 is not mapped
e1000_init_hw_i210
e1000_get_flash_presence_i210
e1000_read_invm_word_i210
//1/bin/Net terminated (SIGSEGV) at 0015:000003D8.
|
|
|
|
|
|
wang long(deleted)
|
Re: I211 support for QNX4
|
|
wang long(deleted)
10/14/2015 8:25 AM
post114639
|
Re: I211 support for QNX4
can I get some update about this?
|
|
|
|
|
|
