The Net.e1000 is for QNX4. You must run devnp-e1000.so for QNX6.4.1.


On 10-07-28 9:09 PM, "Dharmapriya Bandara" <community-noreply@qnx.com>
wrote:

> Hi Hugh,
> Thanks for the response. It didn't work. The file I downloaded looks like a
> corrupt one. Ld reported as a corrupt one. I again downloaded the latest one
> from Foundry27 Rel1718.
> 
> Once unzipped I ran the following:
> 
> ld Net.e1000 
> 
> it reports as follows:
> file not recognized: File format not recognized
> 
> I ran all these under QNX 6.4.1. I am having a feeling that QNX 6.4 doesn't
> recognize this as a binary file. When I run the file manager it reports this
> file as a data file. I changed the attributes of the file too.
> 
> Please help.
> Regards,
> DC
> 
> 
> 
> -----Original Message-----
> From: Hugh Brown [mailto:community-noreply@qnx.com]
> Sent: Wednesday, 28 July 2010 9:57 PM
> To: qnx4-community
> Subject: Re: 82574L Gigabit Ethernet chip and Net.e1000 problem - QNX 6.4.1
> 
> Just run 'Net.e1000 &', but if that doesn't work, then try 'Net.e1000 -d10d3
> &'. Don't use the 'h' after the device ID.
> 
> 
> On 10-07-28 3:03 AM, "Dharmapriya Bandara" <community-noreply@qnx.com>
> wrote:
> 
>>  
>> 
>> Hi,
>> 
>> I am having a Little Board 735 PC104 motherboard with 82574L Gigabit
>> Ethernet Chip. I am trying to run the Net.e1000
>> 
>> driver to get the network working. I ran the following command:
>> 
>> Net.e1000 -d 10d3h -F -i 9 -l 1 -vv
>> 
>> It gives me the following messages:
>> 
>> /bin/Net.e1000[1]: 8hå: cannot execute - No such file or directory
>> 
>> /bin/Net.e1000[2]: [-l: cannot execute - No such file or directory
>> 
>> /bin/Net.e1000[3]: [-s: cannot execute - No such file or directory
>> 
>> /bin/Net.e1000[4]: Where:: cannot execute - No such file or directory
>> 
>> /bin/Net.e1000[5]: -b: cannot execute - No such file or directory
>> 
>> /bin/Net.e1000[6]: -d: cannot execute - No such file or directory
>> 
>> /bin/Net.e1000[7]: -f: cannot execute - No such file or directory
>> 
>> /bin/Net.e1000[8]: syntax error: `(' unexpected
>> 
>> #
>> 
>> Please help.
>> 
>> Regards,
>> 
>> DC
>> 
>> ====
>> 
>> Australian Center for Field Robotics
>> 
>> J04, Rose Street Building
>> 
>> University of Sydney
>> 
>> NSW 2006
>> 
>> Australia
>> 
>> Tel:  61290367179
>> 
>> Fax: 61293517474
>> 
>>  
>> 
>> 
> 
> 
> 
> _______________________________________________
> 
> QNX4 Community
>> Support
> http://community.qnx.com/sf/go/post60839
> 

-- 
Hugh Brown                      (613) 591-0931 ext. 2209 (voice)
QNX Software Systems Ltd.        (613) 591-3579           (fax)
175 Terence Matthews Cres.       email:  hsbrown@qnx.com
Kanata, Ontario, Canada.
K2M 1W8