Release Notes for the QNX Neutrino 6.4.0 BSP for Kontron nanoETXexpress-SP trunk#

System requirements#

Target system#

• QNX Neutrino RTOS 6.4.0
• Board version: Kontron nanoETXexpress-SP
• EEPROM and burner for IPL

Host development system#

• QNX Momentics 6.4.0
• Terminal emulation program (Qtalk, Momentics IDE Terminal, tip, HyperTerminal, ~minicom, etc.)
• RS-232 serial port
• NULL-modem serial cable
• Ethernet link

Getting Started#

Step 1: Connect your hardware#

1. Connect the serial cable to the terminal debug port of the Kontron nanoETXexpress-SP board and to the first serial port on the host machine (e.g. ser1 on a Neutrino host).

On your host, run your terminal application with the following configuration:

• Baud: 115200
• Bits: 8
• Stop bits: 1
• Parity: none
• Hardware flow control: none

Note:If you have a Neutrino host with a serial mouse, you may have to move the mouse to the second serial port on your host, because some terminal programs require the first serial port.

Step 2: Build the BSP#

You can build a BSP OS image from the source code or the binary components contained in a BSP package.

For instructions about building a BSP OS image, please refer to the chapter Working with a BSP in the Building Embedded Systems manual.

Step 3 - (*BIOS Boot*): Transfer the OS image to a bootable USB memory stick#

1. On a Neutrino host, plug the USB key in a USB port (the following steps assume the USB key was mounted as /dev/hd1). At a command prompt: 2. fdisk /dev/hd1 3. Delete existing partitions (hit d, then s) 4. Create a new type 79 partition (hit c, then 79, then 0, then numCylinders-1, then s) 5. Make the partition bootable (hit b, then s) 6. Slay and restart devb-umass 7. dinit /dev/hd1t79 8. dloader /dev/hd1 pc1 9. dloader /dev/hd1t79 pc2 10. Slay and restart devb-umass
Note that steps 1-10 only need to be done once.
11. mount -t qnx /dev/hd1t79 /stick 12. cp -V ifs-kontron_nanoSP.bin 13. Ensure the Kontron nanoETXexpress-SP BIOS is configured to boot from the USB stick 14. Plug the USB key in one of the Kontron nanoETXexpress-SP USB ports 15. Restart the Kontron nanoETXexpress-SP

Step 3 - (*Fastboot*)#

1. Ensure your image is small enough to fit in EEPROM with the microcode (images/CMC_kontron.bin) at 0xD0000. If you have an EEPROM chip of 1MB, that means the entire image must fit in the first 0xD0000 (832K). A larger EEPROM chip will allow you to have a larger image, so long as the microcode is located at 0xD0000 and the IPL is at 0xF0000. 2. Go to the images subdirectory of the BSP and run: 3. ./mkrom.sh kontron-nanoSP.bin
Note that the mkrom.sh script was written for a 1MB EEPROM chip, you'll have to change it for larger chips
4. This will create a fastboot.rom image that can be written to the EEPROM using an EEPROM burner 5. Boot the Kontron nanoETXexpress-SP with the BIOS disabled 6. The IPL will ask you if you want to scan flash for an image or receive an image over the serial link, select "f" to boot the image in EEPPROM