Feed for discussion General in project Web Browsers.

post118664: qnx700 / WebView / WPEWebKit

2018-03-13T16:43:29Z

Is the release story for 7 if you want a WebView, you use a QT WebView?

I've spent some exploration time starting a qnx700 WPEWebKit port. There is a reasonable list of dependencies. Does anyone know if this work is done already, and if so where/who?

Thanks,

Joel

post114539: web browser in QNX 6.5.0

2015-09-29T10:09:09Z

Hello ,

I am trying to get running html page in QNX 6.5 by using wklauncher.

But , getting memory fault error when I go to htttp://www.google.com.

Is there any other way to get the web engine for QNX 6.5? I am not intending to use Mozilla in 6.5.

Then, how to enable for https connection ?

Thanks in advance.

post110467: html5 sample for playbook

2014-05-23T06:53:03Z

Hello:



   i use qnx html5sdk to create a html5 sample.

   when i try to install this bar sample on playbook,it failed.here is the info:failure 881 application author does not match debug token author.

    i have install a new debug token for playbook.

    doesn't anyone know this issue?

post109466: New Web Engine QNX 6.6

2014-03-17T19:08:02Z

Hi,

is there any example or howto to guide us to implement and test new web engine in QNX 6.6?

In last days i've been trying to launch a browser in VM iso of Neutrino version 6.6 but without success.

1. There isn't 'weblauncher' installed in vmware iso able to launch a deployed application.

2. There isn't 'launch' command avaliable in vmware iso, as cited in PDFs.

3. weblauncher and launcher application avaliable only in ARM targets.

Appreciate your help.

Regards,

Jefferson Soares Biernastki

post101846: Re: slinger will not run SSI or CGI in read-only OS filesystem image

2013-05-29T20:45:32Z

In order for SSI commands (and CGI) to be run from slinger it must be started like so:

slinger -es &

See options for http://www.qnx.com/developers/docs/6.5.0_sp1/index.jsp?topic=%2Fcom.qnx.doc.neutrino_utilities%2Fs%2Fslinger.html

post101836: slinger will not run SSI or CGI in read-only OS filesystem image

2013-05-29T19:13:44Z

Attached is my build and boot script for Nitrogren6X.  The issue is SSI and CGI does not work on my target under slinger, although when I tested it on the x86 QNX VM it worked fine.  For example, something like:

    Date and Time (Local): 

shows up like

    Date and Time (Local):

on my Nitrogen6X system.  I have the appropriate libraries built into the image (io-pkt*.so and libsocket.so) so I'm not sure if I'm missing something else.  Also, I'm not sure if slinger SSI and CGI can work under a read-only monolithic OS file system image.  Does it need a writeable filesystem?

post100618: Upload files using HTML forms in slinger

2013-04-16T06:17:46Z

Trying to figure out the right combination of html and CGI scripts to upload a file from a client using HTML forms in slinger. I can only use a C-based CGI scripts.

My secondary question is how to feed a C-based CGI script HTML form input arguments. There doesn't appear to be any examples on how to do this.

post99563: RE: Cannot get wklauncher to work in QNX as described in QNX Web Browser Engine Developer's Guide

2013-02-26T21:57:54Z

Are you running as root?

-----Original Message-----

From: Ralph Canapa [mailto:community-noreply@qnx.com]

Sent: Monday, February 25, 2013 8:28 AM

To: general-web_browsers

Subject: Cannot get wklauncher to work in QNX as described in QNX Web Browser Engine Developer's Guide

I have a Flash (ActionScript 2) front-end running on a QNX system to control lights, temperature and some other features. I'd like to support a webkit browser but I'm having problems displaying the browser correctly using the code provided in examples. I can see that the webkit_kd process is running and I can get a browser screen to display launched by Flash using the QNX-CAR code samples but there are problems with fonts and defining boundaries of the browser port.

So in an effort to handle one problem at a time I'm trying to see if I can get the webkit_kd browser to display local pages without Flash running using the wklauncher application. However I cannot get it to work in QNX as described in the QNX Web Browser Engine Developer's Guide.

Here's my procedure:

1) I've set LD_LIBRARY_PATH

2) I've verified that I have the proper files in $QNX_TARGET/opt/webkit/

3) I've executed $QNX_TARGET/opt/webkit/x86/bin/wklauncher file:\\\aLocalFolder\index.html

and I'm rewarded with:

gf_layer_attach() failed: No such process

GF init failed: are you running io-display?

BTW I'm running io-display

So, is there anyone who can give some guidance on how to solve this problem?

_______________________________________________

General

http://community.qnx.com/sf/go/post99503

To cancel your subscription to this discussion, please e-mail general-web_browsers-unsubscribe@community.qnx.com

post99503: Cannot get wklauncher to work in QNX as described in QNX Web Browser Engine Developer's Guide

2013-02-25T13:27:38Z

I have a Flash (ActionScript 2) front-end running on a QNX system to control lights, temperature and some other features. I'd like to support a webkit browser but I'm having problems displaying the browser correctly using the code provided in examples. I can see that the webkit_kd process is running and I can get a browser screen to display launched by Flash using the QNX-CAR code samples but there are problems with fonts and defining boundaries of the browser port.

So in an effort to handle one problem at a time I'm trying to see if I can get the webkit_kd browser to display local pages without Flash running using the wklauncher application. However I cannot get it to work in QNX as described in the QNX Web Browser Engine Developer's Guide.

Here's my procedure:

1) I've set LD_LIBRARY_PATH

2) I've verified that I have the proper files in $QNX_TARGET/opt/webkit/

3) I've executed $QNX_TARGET/opt/webkit/x86/bin/wklauncher file:\\\aLocalFolder\index.html

and I'm rewarded with:

gf_layer_attach() failed: No such process

GF init failed: are you running io-display?

BTW I'm running io-display

So, is there anyone who can give some guidance on how to solve this problem?

post98460: wklauncher terminates with Memory Fault

2013-01-09T17:08:17Z

Starting wklauncher on platform causes process to terminate as follows:

# wklauncher

LcdControllerR61581: For 480 rows at 136 rows per page (0x0001FE00 bytes) I need 4 pages (0x00080000 bytes). <-- generated by our devg

SlcdcImx25(): Using R61581 for SlcdcImx25LcdTransConfig  <-- generated by our devg

LCD Data Buffer using 524288 of 4194304  <-- generated by our devg

Font face error

Memory fault

#

I have requested to join the web browsers project to get access to the repo for debugging.  Until then, is there a way to increase verbosity on these errors?

Thanks,

Devan

post98250: Re: RE: Embedding webkit with PHOTON APP BUILDER on QNX6.5.0

2012-12-20T10:44:04Z

thanks for the replay,

How to display map(say google map) in UI screen(developing using photon app builder QNX6.5.0) ? And i want to show some indication point on the screen based on the GPS data ? Any idea/suggestion please .....

post98249: RE: Embedding webkit with PHOTON APP BUILDER on QNX6.5.0

2012-12-20T10:09:18Z

The QNX port of WebKit is not designed to be used with the Photon Appbuilder. There is no PtWebServer API layer available for it. Sorry.

Max

-----Original Message-----

From: RAJASEKHAR REDDY YENUGA [mailto:community-noreply@qnx.com]

Sent: Tuesday, December 18, 2012 11:07 AM

To: general-web_browsers

Subject: Embedding webkit with PHOTON APP BUILDER on QNX6.5.0

Hi,

I want to Embedded webkit with QNX6.5.0 Photon App Builder. How to port webkit on QNX6.5.0 & how to embedded this with Photon App builder ?

Any document please .....

_______________________________________________

General

http://community.qnx.com/sf/go/post98212

To cancel your subscription to this discussion, please e-mail general-web_browsers-unsubscribe@community.qnx.com

post98212: Embedding webkit with PHOTON APP BUILDER on QNX6.5.0

2012-12-18T16:06:36Z

Hi,

I want to Embedded webkit with QNX6.5.0 Photon App Builder. How to port webkit on QNX6.5.0 & how to embedded this with Photon App builder ?

Any document please .....

post97245: RE: RE: RE: RE: Webserver/helpserver

2012-11-16T00:25:22Z

The Mozilla browser doesn't use the files you copied. From here it's hard to guess what might be wrong. Did you set execute permissions on those 2 files you copied?

-----Original Message-----

From: Pekka Tuusjärvi [mailto:community-noreply@qnx.com]

Sent: Thursday, November 15, 2012 2:32 AM

To: general-web_browsers

Subject: Re: RE: RE: RE: Webserver/helpserver

Hello,

yes im setting that argument to "online". This code works in QNX 6.3.2 when I use the voyager.

online = vserver,VoyagerServer-2

Yes my URL is "file:///home/system/ohje.htm". It only shows white widget with every URL I try even http://google.com. Those mozilla files exists because I copied them to my runtime afterwards. And I can surf in the web if I start the mozilla browser with /usr/photon/bin/mozilla.

> Are you setting Pt_ARG_WEB_SERVER to "online"? What is the exact URL

> you are passing in? I assume it begins with "file://". Do other URL's

> work, say ones that aren't on the filesystem like http://google.com?

>

> Also, obvious question: Do /opt/Mozilla/mozilla/run-mozilla.sh and

> /opt/ Mozilla/mozilla/mozserver exist and look sane?

>

> Max

>

> -----Original Message-----

> From: Pekka Tuusjärvi [mailto:community-noreply@qnx.com]

> Sent: Monday, November 12, 2012 4:23 AM

> To: general-web_browsers

> Subject: Re: RE: RE: Webserver/helpserver

>

> Hi,

>

> i managed get that error message away but it still wont work. My help

> is on xxx.htm file and mozilla shows it properly when i open it

> straight from mozilla. If i pass the location of that file to

> ptwebclient it wont work. Any suggestions? When i start the webclient

> its ok and no error message from Pt_ARG_WEB_STARTUP_ERRNO.

>

> Here is the line from /etc/photon/webservers

>

> online = /opt/Mozilla/mozilla/run-mozilla.sh

> /opt/Mozilla/mozilla/mozserver, MozillaServer

>

> > > help = mhelpserver,MozHelpServer

> >

> > This is just the default line used for the self hosted help system.

> > Is that what you intended? It means that the executable "mhelpserver"

> > must be in the runtime image and in a directory listed in $PATH. You

> > can always specify an absolute path here instead of updating $PATH.

> >

> > Max

> >

> > -----Original Message-----

> > From: Pekka Tuusjärvi [mailto:community-noreply@qnx.com]

> > Sent: Thursday, September 27, 2012 2:22 AM

> > To: general-web_browsers

> > Subject: Re: RE: Webserver/helpserver

> >

> > Hello,

> >

> > here is the file attached.

> >

> >

> >

> > _______________________________________________

> >

> > General

> > http://community.qnx.com/sf/go/post95869

> > To cancel your subscription to this discussion, please e-mail

> > general- web_browsers-unsubscribe@community.qnx.com

>

>

>

>

>

>

> _______________________________________________

>

> General

> http://community.qnx.com/sf/go/post97080

> To cancel your subscription to this discussion, please e-mail general-

> web_browsers-unsubscribe@community.qnx.com

_______________________________________________

General

http://community.qnx.com/sf/go/post97210

To cancel your subscription to this discussion, please e-mail general-web_browsers-unsubscribe@community.qnx.com

post97210: Re: RE: RE: RE: Webserver/helpserver

2012-11-15T07:32:03Z

Hello,

yes im setting that argument to "online". This code works in QNX 6.3.2 when I use the voyager.

online = vserver,VoyagerServer-2

Yes my URL is "file:///home/system/ohje.htm". It only shows white widget with every URL I try even http://google.com. Those mozilla files exists because I copied them to my runtime afterwards. And I can surf in the web if I start the mozilla browser with /usr/photon/bin/mozilla.

> Are you setting Pt_ARG_WEB_SERVER to "online"? What is the exact URL you are

> passing in? I assume it begins with "file://". Do other URL's work, say ones

> that aren't on the filesystem like http://google.com?

>

> Also, obvious question: Do /opt/Mozilla/mozilla/run-mozilla.sh and /opt/

> Mozilla/mozilla/mozserver exist and look sane?

>

> Max

>

> -----Original Message-----

> From: Pekka Tuusjärvi [mailto:community-noreply@qnx.com]

> Sent: Monday, November 12, 2012 4:23 AM

> To: general-web_browsers

> Subject: Re: RE: RE: Webserver/helpserver

>

> Hi,

>

> i managed get that error message away but it still wont work. My help is on

> xxx.htm file and mozilla shows it properly when i open it straight from

> mozilla. If i pass the location of that file to ptwebclient it wont work. Any

> suggestions? When i start the webclient its ok and no error message from

> Pt_ARG_WEB_STARTUP_ERRNO.

>

> Here is the line from /etc/photon/webservers

>

> online = /opt/Mozilla/mozilla/run-mozilla.sh /opt/Mozilla/mozilla/mozserver,

> MozillaServer

>

> > > help = mhelpserver,MozHelpServer

> >

> > This is just the default line used for the self hosted help system. Is

> > that what you intended? It means that the executable "mhelpserver"

> > must be in the runtime image and in a directory listed in $PATH. You

> > can always specify an absolute path here instead of updating $PATH.

> >

> > Max

> >

> > -----Original Message-----

> > From: Pekka Tuusjärvi [mailto:community-noreply@qnx.com]

> > Sent: Thursday, September 27, 2012 2:22 AM

> > To: general-web_browsers

> > Subject: Re: RE: Webserver/helpserver

> >

> > Hello,

> >

> > here is the file attached.

> >

> >

> >

> > _______________________________________________

> >

> > General

> > http://community.qnx.com/sf/go/post95869

> > To cancel your subscription to this discussion, please e-mail general-

> > web_browsers-unsubscribe@community.qnx.com

>

>

>

>

>

>

> _______________________________________________

>

> General

> http://community.qnx.com/sf/go/post97080

> To cancel your subscription to this discussion, please e-mail general-

> web_browsers-unsubscribe@community.qnx.com

post97115: RE: RE: RE: Webserver/helpserver

2012-11-12T20:26:23Z

Are you setting Pt_ARG_WEB_SERVER to "online"? What is the exact URL you are passing in? I assume it begins with "file://". Do other URL's work, say ones that aren't on the filesystem like http://google.com?

Also, obvious question: Do /opt/Mozilla/mozilla/run-mozilla.sh and /opt/Mozilla/mozilla/mozserver exist and look sane?

Max

-----Original Message-----

From: Pekka Tuusjärvi [mailto:community-noreply@qnx.com]

Sent: Monday, November 12, 2012 4:23 AM

To: general-web_browsers

Subject: Re: RE: RE: Webserver/helpserver

Hi,

i managed get that error message away but it still wont work. My help is on xxx.htm file and mozilla shows it properly when i open it straight from mozilla. If i pass the location of that file to ptwebclient it wont work. Any suggestions? When i start the webclient its ok and no error message from Pt_ARG_WEB_STARTUP_ERRNO.

Here is the line from /etc/photon/webservers

online = /opt/Mozilla/mozilla/run-mozilla.sh /opt/Mozilla/mozilla/mozserver,MozillaServer

> > help = mhelpserver,MozHelpServer

>

> This is just the default line used for the self hosted help system. Is

> that what you intended? It means that the executable "mhelpserver"

> must be in the runtime image and in a directory listed in $PATH. You

> can always specify an absolute path here instead of updating $PATH.

>

> Max

>

> -----Original Message-----

> From: Pekka Tuusjärvi [mailto:community-noreply@qnx.com]

> Sent: Thursday, September 27, 2012 2:22 AM

> To: general-web_browsers

> Subject: Re: RE: Webserver/helpserver

>

> Hello,

>

> here is the file attached.

>

>

>

> _______________________________________________

>

> General

> http://community.qnx.com/sf/go/post95869

> To cancel your subscription to this discussion, please e-mail general-

> web_browsers-unsubscribe@community.qnx.com

_______________________________________________

General

http://community.qnx.com/sf/go/post97080

To cancel your subscription to this discussion, please e-mail general-web_browsers-unsubscribe@community.qnx.com

post97080: Re: RE: RE: Webserver/helpserver

2012-11-12T09:23:00Z

Hi,

i managed get that error message away but it still wont work. My help is on xxx.htm file and mozilla shows it properly when i open it straight from mozilla. If i pass the location of that file to ptwebclient it wont work. Any suggestions? When i start the webclient its ok and no error message from Pt_ARG_WEB_STARTUP_ERRNO.

Here is the line from /etc/photon/webservers

online = /opt/Mozilla/mozilla/run-mozilla.sh /opt/Mozilla/mozilla/mozserver,MozillaServer

> > help = mhelpserver,MozHelpServer

>

> This is just the default line used for the self hosted help system. Is that

> what you intended? It means that the executable "mhelpserver" must be in the

> runtime image and in a directory listed in $PATH. You can always specify an

> absolute path here instead of updating $PATH.

>

> Max

>

> -----Original Message-----

> From: Pekka Tuusjärvi [mailto:community-noreply@qnx.com]

> Sent: Thursday, September 27, 2012 2:22 AM

> To: general-web_browsers

> Subject: Re: RE: Webserver/helpserver

>

> Hello,

>

> here is the file attached.

>

>

>

> _______________________________________________

>

> General

> http://community.qnx.com/sf/go/post95869

> To cancel your subscription to this discussion, please e-mail general-

> web_browsers-unsubscribe@community.qnx.com

post95899: RE: RE: Webserver/helpserver

2012-09-27T19:01:28Z

> help = mhelpserver,MozHelpServer

This is just the default line used for the self hosted help system. Is that what you intended? It means that the executable "mhelpserver" must be in the runtime image and in a directory listed in $PATH. You can always specify an absolute path here instead of updating $PATH.

Max

-----Original Message-----

From: Pekka Tuusjärvi [mailto:community-noreply@qnx.com]

Sent: Thursday, September 27, 2012 2:22 AM

To: general-web_browsers

Subject: Re: RE: Webserver/helpserver

Hello,

here is the file attached.

_______________________________________________

General

http://community.qnx.com/sf/go/post95869

To cancel your subscription to this discussion, please e-mail general-web_browsers-unsubscribe@community.qnx.com

post95869: Re: RE: Webserver/helpserver

2012-09-27T06:21:52Z

Hello,

here is the file attached.

post95813: RE: Webserver/helpserver

2012-09-25T23:45:37Z

Can you show the contents of your /etc/photon/webservers file? Make sure that this file exists in your image, and that the "help = ..." line properly references an existing executable.

Max

-----Original Message-----

From: Pekka Tuusjärvi [mailto:community-noreply@qnx.com]

Sent: Tuesday, September 25, 2012 6:29 AM

To: general-web_browsers

Subject: Webserver/helpserver

We have used webserver vserver for our help manual. We have showed our help manual in a HTML as a part of our IDE. Now in 6.5.0 it doesn´t work after we make a runtime image. What should I do?

Even in example VMWare image in QNX website the help doesn´t work. I attached a photo about the error message.

_______________________________________________

General

http://community.qnx.com/sf/go/post95786

To cancel your subscription to this discussion, please e-mail general-web_browsers-unsubscribe@community.qnx.com

post95786: Webserver/helpserver

2012-09-25T10:28:36Z

We have used webserver vserver for our help manual. We have showed our help manual in a HTML as a part of our IDE. Now in 6.5.0 it doesn´t work after we make a runtime image. What should I do?

Even in example VMWare image in QNX website the help doesn´t work. I attached a photo about the error message.

post93475: Re: Test

2012-06-03T12:13:47Z

Tested. OK

post93474: Test

2012-06-03T11:59:36Z

Sorry for spamming. This is test query.

post91158: RE: RE: How to get user name and password to download source code of QNX community

2012-01-26T05:40:21Z

Please see:

http://community.qnx.com/sf/wiki/do/viewPage/projects.community/wiki/UpdatedQNXSourceAccessPolicyFAQ

-----Original Message-----

From: Donald Ong [mailto:community-noreply@qnx.com]

Sent: Wednesday, January 25, 2012 9:55 PM

To: general-web_browsers

Subject: Re: RE: How to get user name and password to download source code of QNX community

Anyone have any success on the download? How can I contact the team lead of this project?

_______________________________________________

General

http://community.qnx.com/sf/go/post91154

post91157: RE: Are there any build of Webkit for QNX 6.3.2?

2012-01-26T05:34:31Z

Note that the QNX port of WebKit first released with 6.4.x was never integrated with Photon, so it cannot act as a replacement for vserver or mozserver.

The aforementioned WebKit port uses the QNX graphics framework (GF).

Regards,

Max

-----Original Message-----

From: Donald Ong [mailto:community-noreply@qnx.com]

Sent: Wednesday, January 25, 2012 9:58 PM

To: general-web_browsers

Subject: Are there any build of Webkit for QNX 6.3.2?

Hi,

May I know if there are any build of Webkit for QNX 6.3.2?

I would love to test it out, to see if it can replace the current vserver, mozilla web engine.

Please advise.

Donald

_______________________________________________

General

http://community.qnx.com/sf/go/post91155

post91155: Are there any build of Webkit for QNX 6.3.2?

2012-01-26T02:58:11Z

Hi,

May I know if there are any build of Webkit for QNX 6.3.2?

I would love to test it out, to see if it can replace the current vserver, mozilla web engine.

Please advise.

Donald

post91154: Re: RE: How to get user name and password to download source code of QNX community

2012-01-26T02:54:50Z

Anyone have any success on the download? How can I contact the team lead of this project?

post90487: RE: How to get user name and password to download source code of QNX community

2011-12-08T14:33:28Z

No success :(

-----Original Message-----

From: Alex Mills [mailto:community-noreply@qnx.com]

Sent: Thursday, December 08, 2011 9:32 AM

To: general-web_browsers

Subject: Re: How to get user name and password to download source code of QNX community

Would love to know if you had any progress as I also cannot access the repo with my username and password.

_______________________________________________

General

http://community.qnx.com/sf/go/post90486

post90486: Re: How to get user name and password to download source code of QNX community

2011-12-08T14:31:41Z

Would love to know if you had any progress as I also cannot access the repo with my username and password.

post89158: RE: WebGL

2011-09-29T14:56:15Z

Indirectly, yes. The QNX WebKit port is now deprecated in favour of the Torch WebKit port, as used on the Playbook. The RIM/QNX Torch Browser team is in the final stages of integrating WebGL. The details of making the Torch WebKit port available to QNX customers are still being worked out.

Regards,

Max

mfeil@qnx.com

-----Original Message-----

From: Richard Elswick [mailto:community-noreply@qnx.com]

Sent: Thursday, September 29, 2011 9:22 AM

To: general-web_browsers

Subject: WebGL

Is anyone working on integrating WebGL into Webkit for QNX of course.

_______________________________________________

General

http://community.qnx.com/sf/go/post89153

post89153: WebGL

2011-09-29T13:22:25Z

Is anyone working on integrating WebGL into Webkit for QNX of course.

post87733: Slinger support for server push

2011-08-01T13:33:15Z

Hello Everyone,

Is there some way that the slinger webserver can push data to the web browser?

My requirement is that I make a request from my client application to a service that is running on the target & gets back the response from the service.

The client is a thin client in the form of html pages running from the web browser on the PC. The webserver is slinger.

Once the response is available from the service is it possible for the slinger webserver to push this response to the web browser on the PC?

Currently we are using a pull mechanism. We use javascript for this. We have a timer which expires every 2 seconds.

When the timer expires we do a GET from the thin client that pulls the response.

The preferred mechanism is a push so that the slinger webserver pushes the response to the web browser whenever it is available.

If slinger does not already support this is there some alternative mechanism?

I would appreciate any help on this. Thanks in advance.

Regards,

Sonia.

post87226: RE: Cannot find WebView.h

2011-07-09T02:20:00Z

The source for the QNX port of the WebKit web browser engine is

available in the web-browsers project on Foundry27 (community.qnx.com).

You will need to request access if you do not have access already.

-----Original Message-----

From: sun sun [mailto:community-noreply@qnx.com]

Sent: Thursday, July 07, 2011 10:07 PM

To: general-web_browsers

Subject: Cannot find WebView.h

I want to use Web Browser Engine on SDP 6.5.0, and I am following

http://www.qnx.com/developers/docs/6.5.0/index.jsp?topic=/com.qnx.doc.we

bkit/bookset.html. But, I cannot find the header file WebView.h. The

Web Browser Engine is a separate product that need to be installed

manually?

_______________________________________________

General

http://community.qnx.com/sf/go/post87198

post87198: Cannot find WebView.h

2011-07-08T02:07:18Z

I want to use Web Browser Engine on SDP 6.5.0, and I am following http://www.qnx.com/developers/docs/6.5.0/index.jsp?topic=/com.qnx.doc.webkit/bookset.html. But, I cannot find the header file WebView.h. The Web Browser Engine is a separate product that need to be installed manually?

post87038: skia support?

2011-07-04T14:29:10Z

Hi everyone,

I just saw that QNX should provide a skia api (http://www.qnx.com/products/hmi/hmi.html -> technology -> 2D/3D). Unfortunately I cannot find anything else about skia for api. Does someone know where I can get this api and which device backends are supported by skia for qnx?

I would appreciate any help. Thanks in advance,

bjoern

post86893: How to get user name and password to download source code of QNX community

2011-06-28T07:37:19Z

Hello, I try to download the following link

http://community.qnx.com/svn/repos/web-browsers/webkit/trunk/

but it ask for my user name and password . And I try my account to this forum but failed.

How to get it ? Thanks.

post86846: Firefox 3.5.3 Vs latest version of webkit

2011-06-24T20:52:54Z

Hi,

Currently I am working on web browser for QNX CAR. I am trying to find following details as mentioned below:

1) I understand the browser is available in distributed form as in flash GUI is with HMI layer, webkit_kd is in the middleware. Please comment on my understanding.

2) Is the existing browser within QNX CAR as in GUI + middleware backend with some additional services capable of full featured browsing experience as in blackberry playbook?

3) Does this browser support media playback of live RTP elementary streams?

4) How is this browser in comparison with Firefox 3.5.3 version? Please share your comments.

Thanks & Regards,

Mahesh

post85620: Re: running perl script file through slinger web server on QNX6.3

2011-05-12T13:37:57Z

1. Save the page as index.shtml rather than index.html.

2. export HTTPD_ROOT_DOC=index.shtml

3. Start the web-sever with the following options --> slinger -e -s -p 80 &

It should work now.

Nadeem.

post84947: Re: Porting of a web gui from QNX 6.3.2 to QNX 6.4.1 using Slinger Web Server

2011-04-13T16:06:11Z

Hello,

I realize this is a bit late but figured I'd answer it anyway in case anyone else needs to know.

The reason it's happening is that slinger ignores SIGCHLD. If you want your cgi program to be able to spawn and then grab the return value, you need to stop ignoring SIGCHLD:

signal(SIGCHLD,SIG_DFL); // Set SIGCHLD back to default

Cheers,

Matt M

post82564: Write data to data server process using form

2011-01-24T11:38:29Z

Hello,

I would like to write data to data server (ds) that is entered into the HTML form field

and submitted.

However I cannot understand, how can one manipulate the string value " data" so that it takes the value entered in the form. ()

Normal qnxvar write works well and the variable change in the webserver is reflected on the html page.

Thanks,

Abhi

-----------------------------------------------------------------------------------------------------

Here is my HTML form code :

<META HTTP-EQUIV="" CONTENT="2;URL=index.shtml">

<html>

<head>

<title>AT91SAM9G20</title>

</head>

<body>

<tr><td valign="top"></td>

<td valign="top"><h2><i><B>Status</B></i></h2></td></tr>



<P>







<P>



<form name="input" action="index.shtml" method="get">

Set Variable: <input type="text" name="ABHI" 



<input type="submit" value="Submit" />

</form>

</body>

</html>

------------------------------------------------------------------------------------------------------

post82235: RE: RE: RE: SVG

2011-01-13T21:37:23Z

Hi Glenn. Skia is currently used only in the QNX port of WebKit. It is a

purely software renderer with no hardware accelerated back end. The

client app passes the WebKit library a surface (i.e. memory buffer),

which it then attaches to a Skia canvas. The client app is then free to

use gf, gles, or whatever for the final blitting & compositing.

Max

-----Original Message-----

From: Glenn Schmottlach [mailto:community-noreply@qnx.com]

Sent: Thursday, January 13, 2011 4:32 PM

To: general-web_browsers

Subject: Re: RE: RE: SVG

Is the QNX port of Skia available yet from QNX? If I have QNX Screens

can I expect to use this library to complement (or possibly replace) GF?

Also, does your actual Skia implementation use GF or something like

OpenVG/GL-ES as the backend?

Thanks,

Glenn

_______________________________________________

General

http://community.qnx.com/sf/go/post82231

post82231: Re: RE: RE: SVG

2011-01-13T21:31:57Z

Is the QNX port of Skia available yet from QNX? If I have QNX Screens can I expect to use this library to complement (or possibly replace) GF?

Also, does your actual Skia implementation use GF or something like OpenVG/GL-ES as the backend?

Thanks,

Glenn

post79245: RE: SVG

2010-12-17T20:10:09Z

Is there any update on SVG support? I would like to draw a scalable graphic onto a screen in C++ and noticed that libImg does not claim support for SVGs.

Any information on when or how SVG support will be added would be much appreciated.

Thanks!

post77209: RE: Firefox Crashes

2010-12-03T22:15:37Z

Hi Martin. The only alternative to Firefox is the QNX WebKit port which

was released with 6.4.1 and 6.5.0. It is quite different and may pose

new challenges. Are you currently using the embeddable mozserver or the

full Bon Echo (with menus, etc)? WebKit is a lot more like mozserver in

that your own front end needs to be written.

You are at the latest version of QNX firefox. It is no longer under

development.

If there is no core file it usually means the program is calling exit().

Are there any error messages or return code that you can see? Probably

the best way to figure out what's happening is to have someone here at

QNX reproduce the problem in the debugger. If you can submit a problem

report with a small sample web page that reproduces the problem that

would help.

Regards,

Max

-----Original Message-----

From: Martin Doane [mailto:community-noreply@qnx.com]

Sent: Friday, December 03, 2010 4:58 PM

To: general-web_browsers

Subject: Firefox Crashes

I hope this is the appropriate place to post this. If not, please

suggest an alternative.

We use Firefox (Bon Echo 2.0.0.20) running on QNX 6.4.1 as the human

interface for our product. We've tried QNX 6.5.0 with no improvement.

The web server is hosted on another machine, and is based on Apache

Tomcat. The pages use javascript extensively.

Firefox occasionally (randomly) responds to a click on a page by

abruptly terminating. Dumper is running, but no core file is created. A

Windows version of Firefox (3.6.12) does not experience this problem,

nor does IE on Windows.

Questions:

* Is there an alternative to Firefox that I can use?

* Is there a later version of Firefox available for QNX?

* Is there a way to determine the cause of the termination?

TIA,

Marty

_______________________________________________

General

http://community.qnx.com/sf/go/post77208

post77208: Firefox Crashes

2010-12-03T21:57:57Z

I hope this is the appropriate place to post this. If not, please suggest an alternative.

We use Firefox (Bon Echo 2.0.0.20) running on QNX 6.4.1 as the human interface for our product. We've tried QNX 6.5.0 with no improvement. The web server is hosted on another machine, and is based on Apache Tomcat. The pages use javascript extensively.

Firefox occasionally (randomly) responds to a click on a page by abruptly terminating. Dumper is running, but no core file is created. A Windows version of Firefox (3.6.12) does not experience this problem, nor does IE on Windows.

Questions:

* Is there an alternative to Firefox that I can use?

* Is there a later version of Firefox available for QNX?

* Is there a way to determine the cause of the termination?

TIA,

Marty

post73513: subscribe

2010-11-04T11:46:23Z

Todd Holly

Software Product Engineering

507 Plymouth Ave. NE

Grand Rapids, Michigan, 49505

616.913.5536

todd.holly@dematic.com <mailto:todd.holly@dematic.com>

DEMATIC l Creating Logistics Results

CONFIDENTIALITY: This information contained herein and any attachments

is confidential and may be privileged. If you are not the intended

recipient referred to above, do not disclose, copy, forward, or retain

the contents or take any actions in reliance upon it. If you have

received this in error, please contact the sender and delete all

electronic copies, and destroy any hard copies.

post73499: Re: RE: RE: SVG

2010-11-04T02:40:40Z

Hi Max,

Is SVG supported by webkit in QNX 6.5.0 release?

Ramesh

post66783: Call to img_load_file() fails with IMG_ERR_FORMAT

2010-09-11T00:05:18Z

according to the documentation this is an indication that the img_codec_*.so file could not be found.

The files are not in /lib/dll but they are in /qnx-car/x86/lib/dll. I cannot copy the require files into the /lib/dll folder. I have touched and chmoded the lib and dll folders but the permissions do not change from read only. My LD_LIBRARY_PATH is pointing to /qnx-car/x86/lib/dll but the function call still fails.

How do I change permissions on the /lib/dll folders? Is there some other environment variable that I need to set in order for the img_load_file() function call to succeed?

post66382: gf_layer_attach() failed when running wklauncher

2010-09-08T17:10:25Z

io-display is running.

When I type the command vsync it shows:

Number of displays: 1

Display 0: 800x400, refresh = 60hz

Number of Layers: 4

gf_layer_atach() failed

Returning from main() with 1

I read in another post that by not logging into Photon wklauncher would run and display the browser window.

http://community.qnx.com/sf/discussion/do/listPosts/projects.web_browsers/discussion.general.topc15124?_pagenum=11

I am not using Photon, so how do I see if it is running.  pidin arg did not show any process called Photon.

How does one not login to photon?  The QNX Car platform that was shipped to me automatically starts the HMI application, so maybe there is an issue with running wklauncher while the HMI app is running.

Thanks.

post66162: RE: what opt-crank files are needed on Neutrino

2010-09-07T17:44:39Z

You can see which shared libs are needed by looking in the following

folder on your host system: $QNX_TARGET/opt/webkit/x86/lib

-----Original Message-----

From: Darrin Garrett [mailto:community-noreply@qnx.com]

Sent: Tuesday, September 07, 2010 12:04 PM

To: general-web_browsers

Subject: what opt-crank files are needed on Neutrino

I was attempting to copy the required crank.3.3 files from my Linux

build machine to my Intel Atom board an noticed the size on disk of the

crank.3.3 folder is 289 mega bytes. If I only need the runtime libs

then what folders should I copy to the Intel Atom board?

Also, it there a Tar package for QNX?

Thanks

Darrin

_______________________________________________

General

http://community.qnx.com/sf/go/post66148

post66148: what opt-crank files are needed on Neutrino

2010-09-07T16:03:42Z

I was attempting to copy the required crank.3.3 files from my Linux build machine to my Intel Atom board an noticed the size on disk of the crank.3.3 folder is 289 mega bytes. If I only need the runtime libs then what folders should I copy to the Intel Atom board?

Also, it there a Tar package for QNX?

Thanks

Darrin

post66088: draw a bitmap in browser plugin

2010-09-07T09:07:07Z

Hello,everyone

Have ever tried to draw a bitmap (.bmp or .jeg) in a browser plugin?

I can draw that in a QNX stand alone app,but when I

use if (img_lib_attach(&ilib)!= IMG_ERR_OK) {}

it report error .

Can you give me some code snipts?

thank you very much!

post65576: Re: RE: cmake issue running the configure scripts on ubuntu 10.4

2010-09-01T21:58:36Z

it seems cmake was not changing the cache file and I needed to manually change it so all the compiler paths pointed to the correct location for gcc and other output directories.

The configuration script is working now.

post65552: Re: RE: cmake issue running the configure scripts on ubuntu 10.4

2010-09-01T19:38:23Z

By SDP you mean Software Development Platform?

QNX SDP is installed at /opt/qnx641

Momentics works.

from env I get:

QNX_HOST=/opt/qnx641/host/linux/x86

post65547: RE: cmake issue running the configure scripts on ubuntu 10.4

2010-09-01T19:16:11Z

Your $QNX_HOST environment variable is not set, so maybe you don't have

the QNX SDP installed? Or if you just recently installed it, you have

not logged out and then back in to make sure the environment variables

get set in new shells.

-----Original Message-----

From: Darrin Garrett [mailto:community-noreply@qnx.com]

Sent: Wednesday, September 01, 2010 12:00 PM

To: general-web_browsers

Subject: cmake issue running the configure scripts on ubuntu 10.4

I am new to cmake, and have an issue when i follow the webkit readme

build instructions.  When I run the configure script

../build-scripts/configure-owb x86 "" from webket/trunk/nto-x86-gf

directory I get:

loading initial cache file ../cmake/ConfigureBuildGf.cmake

-- The CXX compiler identification is unknown

-- The C compiler identification is unknown

-- Check for working CXX compiler: /usr/bin/qcc

CMake Error: your CXX compiler: "/usr/bin/qcc" was not found.   Please

set CMAKE_CXX_COMPILER to a valid compiler path or name.

CMake Error: Internal CMake error, TryCompile configure of cmake failed

-- Check for working CXX compiler: /usr/bin/qcc -- broken

CMake Error at

/usr/share/cmake-2.8/Modules/CMakeTestCXXCompiler.cmake:43 (MESSAGE):

  The C++ compiler "/usr/bin/qcc" is not able to compile a simple test

  program.

  It fails with the following output:



  CMake will not be able to correctly generate this project.

Call Stack (most recent call first):

  CMakeLists.txt:7 (project)

CMake Error: your CXX compiler: "/usr/bin/qcc" was not found.   Please

set CMAKE_CXX_COMPILER to a valid compiler path or name.

CMake Error: your C compiler: "/usr/bin/qcc" was not found.   Please set

CMAKE_C_COMPILER to a valid compiler path or name.

-- Configuring incomplete, errors occurred!

I know gcc and g++ are working an reside in /usr/bin  so I have not been

able to determine why cmake cannot find the compilers.  Anyone have any

ideas on what is wrong and how to fix it?

The cmake web site talks about a the need for a CMakeLists.txt file,

which I cannot find anywhere under opt/web-browsers.

Thanks

_______________________________________________

General

http://community.qnx.com/sf/go/post65509

post65542: Re: cmake issue running the configure scripts on ubuntu 10.4

2010-09-01T18:43:20Z

attached is the cache file that was generated

post65509: cmake issue running the configure scripts on ubuntu 10.4

2010-09-01T15:59:49Z

I am new to cmake, and have an issue when i follow the webkit readme build instructions.  When I run the configure script ../build-scripts/configure-owb x86 "" from webket/trunk/nto-x86-gf directory I get:

loading initial cache file ../cmake/ConfigureBuildGf.cmake

-- The CXX compiler identification is unknown

-- The C compiler identification is unknown

-- Check for working CXX compiler: /usr/bin/qcc

CMake Error: your CXX compiler: "/usr/bin/qcc" was not found.   Please set CMAKE_CXX_COMPILER to a valid compiler path or name.

CMake Error: Internal CMake error, TryCompile configure of cmake failed

-- Check for working CXX compiler: /usr/bin/qcc -- broken

CMake Error at /usr/share/cmake-2.8/Modules/CMakeTestCXXCompiler.cmake:43 (MESSAGE):

  The C++ compiler "/usr/bin/qcc" is not able to compile a simple test

  program.

  It fails with the following output:



  CMake will not be able to correctly generate this project.

Call Stack (most recent call first):

  CMakeLists.txt:7 (project)

CMake Error: your CXX compiler: "/usr/bin/qcc" was not found.   Please set CMAKE_CXX_COMPILER to a valid compiler path or name.

CMake Error: your C compiler: "/usr/bin/qcc" was not found.   Please set CMAKE_C_COMPILER to a valid compiler path or name.

-- Configuring incomplete, errors occurred!

I know gcc and g++ are working an reside in /usr/bin  so I have not been able to determine why cmake cannot find the compilers.  Anyone have any ideas on what is wrong and how to fix it?

The cmake web site talks about a the need for a CMakeLists.txt file, which I cannot find anywhere under opt/web-browsers.

Thanks

post65308: RE: Building Webkit on ubuntu 9.04

2010-08-31T19:43:39Z

thanks

-----Original Message-----

From: Max Feil [mailto:community-noreply@qnx.com]

Sent: Tuesday, August 31, 2010 12:33 PM

To: general-web_browsers

Subject: RE: Building Webkit on ubuntu 9.04

You should be fine with newer versions of Ubuntu. I am using 10.04 LTS.

-----Original Message-----

From: Darrin Garrett [mailto:community-noreply@qnx.com]

Sent: Tuesday, August 31, 2010 1:58 PM

To: general-web_browsers

Subject: Building Webkit on ubuntu 9.04

The latest readme file specifies that you can build webkit on ubuntu

9.04.

Has anyone tried with success to build webkit on a newer version of

ubuntu?

the opt-crank will install on ubuntu 10.04 with the addition of

ia32-libs

Thanks

_______________________________________________

General

http://community.qnx.com/sf/go/post65269

_______________________________________________

General

http://community.qnx.com/sf/go/post65296

The information contained in this message, including attachments, may contain privileged and/or confidential information that is intended to be delivered only to the person(s) identified above. If you are not the intended recipient(s), or the person responsible for delivering this message to the intended recipient(s), Airbiquity Inc. requests that you immediately notify the sender and asks that you do not read the message or its attachments and that you delete them without copying or sending them to anyone else. Any review, reliance or distribution by others not intended as recipients or forwarding without express permission is strictly prohibited. Replies to this message may be received by other Airbiquity personnel in addition to the intended recipient(s).

post65296: RE: Building Webkit on ubuntu 9.04

2010-08-31T19:33:05Z

You should be fine with newer versions of Ubuntu. I am using 10.04 LTS.

-----Original Message-----

From: Darrin Garrett [mailto:community-noreply@qnx.com]

Sent: Tuesday, August 31, 2010 1:58 PM

To: general-web_browsers

Subject: Building Webkit on ubuntu 9.04

The latest readme file specifies that you can build webkit on ubuntu

9.04.

Has anyone tried with success to build webkit on a newer version of

ubuntu?

the opt-crank will install on ubuntu 10.04 with the addition of

ia32-libs

Thanks

_______________________________________________

General

http://community.qnx.com/sf/go/post65269

post65269: Building Webkit on ubuntu 9.04

2010-08-31T17:58:09Z

The latest readme file specifies that you can build webkit on ubuntu 9.04.

Has anyone tried with success to build webkit on a newer version of ubuntu?

the opt-crank will install on ubuntu 10.04 with the addition of ia32-libs

Thanks

post64957: how to setup webkit_kd build environment?

2010-08-30T08:03:03Z

Hi

QNX gurus

I am very confused about setting up the environment to buid webkit_kid under Neutrino6.5 .

Now I have the environment to build webkit success.

Thanks a lot.

post64465: Problems building qnx car web-browser

2010-08-25T21:25:00Z

Hi everyone

I can't seem to get the qnx car web-browser under

/qnx/trunk/webkit_kd to build correctly

specifically I see errors like

"free" was not declared

upon inspection i see I am getting errors like

undefined reference to stdio.h, WebKit.h and others.

How/Where can I include these files (and stdio? really? how can that not be linked?)

Any help is truly appreciated.

Thanks

Jon

post64166: owb failing html5test.com maps.google.com and others

2010-08-24T17:21:33Z

Hi I recently got the build running, and for normal webpages like http://www.google.com it is showing correctly.

But if I pass in something like

./owb http://maps.google.com

mouse and keyboard inputs are frozen and I have to kill owb from Momentics.

If i try to run html5test.com, I get disconnected and I have to hard restart my test machine.

Are anyone else noticing these issues?

post64014: wklauncher source code

2010-08-23T22:17:21Z

Hello,

Whenever I attempt to retrieve the source code for the wklauncher sample app I receive an error:

Forbidden

You don't have permission to access /svn/repos/web-browsers/webkit/trunk/WebKitTools/OWBLauncher/Gf/ on this server.

I understand from other posst on this discussions group that this source code is restricted. I applied for restricted access on the 8/10 and received a request confirmation from QNX on 8/12. I have not heard anything yet but I very much need access to this code. How can I find out the status of my request for access to restricted code so in my point of view it is no longer restricted?

Darrin

post63939: lighttpd Problem

2010-08-23T14:29:20Z

Hello,

I am currently working with lighttpd (version 1.4.26) and QNX and have a very strange problem:

If any of my files gets bigger than 24.548 kb the transmission takes ages.

Any blocks smaller than 24k are transmitted without any problems, but if they are bigger eg 50 k the transmisstion of a first 24k is realy fast, and then it takes about 1-2 minutes thill the next 24k block is transmitted.

Has anyone noticed simmilar problems? Or has anyone a clue what could be the problem?

Best regards,

Alex

post63643: RE: RE: RE: Error building web-browsers project in linux host

2010-08-19T22:06:02Z

Make sure devi-hid is running:

devi-hid -P mouse kbd

-----Original Message-----

From: Jonathan Wong [mailto:community-noreply@qnx.com]

Sent: Thursday, August 19, 2010 4:27 PM

To: general-web_browsers

Subject: Re: RE: RE: Error building web-browsers project in linux host

so I can run owb if I do not login with photon. After launch, I see a

full screen browser.

One last thing is that I am unable to use my mouse and/or keyboard for

navigating. Upon exiting owb, I see a message of ">> No Input Available

how do I manually specify a keyboard and mouse?

Thanks

Jon

> This is the output of vsync

>

> #vsync

> Number of displays: 1

> Display 0: 1680x1050, refresh = 60hz

> Number of Layers: 4

> gf_layer_atach() failed

> Returning from main() with 1

>

> and the output from egl-gears

>

> #egl-gears

> gf_layer_attach() failed

>

>

> > Can you run "vsync" and "egl-gears" using your io-display settings?

Or

> > is the display scrambled for those as well?

> >

> > I would also try other screen resolutions in display.conf just to

see if

> > it's a timing issue.

> >

> > -----Original Message-----

> > From: Jonathan Wong [mailto:community-noreply@qnx.com]

> > Sent: Wednesday, August 18, 2010 5:40 PM

> > To: general-web_browsers

> > Subject: Re: RE: Error building web-browsers project in linux host

> >

> > Please point to anything I might be doing wrong.

> > I built the binaries from a linux host (per instructions) and

transfered

> > them over to the machine running QNX Neutrino.

> >

> > I have Momentics running and I see that io-display is already

running.

> > How if I just do:

> >

> > # ./owb http://www.google.com

> >

> > I get a

> >

> > gf_layer_attach() failed: no such process

> > GF init failed: are you running io-display

> >

> > so if I run

> >

> > io-display -dvid=0x8086,did=0x27ae

> >

> > and then run owb again, i get my scrambled display.

> >

> > Am I doing something incorrectly?

> >

> >

> >

> > _______________________________________________

> >

> > General

> > http://community.qnx.com/sf/go/post63490

>

>

_______________________________________________

General

http://community.qnx.com/sf/go/post63637

post63637: Re: RE: RE: Error building web-browsers project in linux host

2010-08-19T20:26:55Z

so I can run owb if I do not login with photon. After launch, I see a full screen browser.

One last thing is that I am unable to use my mouse and/or keyboard for navigating. Upon exiting owb, I see a message of ">> No Input Available

how do I manually specify a keyboard and mouse?

Thanks

Jon

> This is the output of vsync

>

> #vsync

> Number of displays: 1

> Display 0: 1680x1050, refresh = 60hz

> Number of Layers: 4

> gf_layer_atach() failed

> Returning from main() with 1

>

> and the output from egl-gears

>

> #egl-gears

> gf_layer_attach() failed

>

>

> > Can you run "vsync" and "egl-gears" using your io-display settings? Or

> > is the display scrambled for those as well?

> >

> > I would also try other screen resolutions in display.conf just to see if

> > it's a timing issue.

> >

> > -----Original Message-----

> > From: Jonathan Wong [mailto:community-noreply@qnx.com]

> > Sent: Wednesday, August 18, 2010 5:40 PM

> > To: general-web_browsers

> > Subject: Re: RE: Error building web-browsers project in linux host

> >

> > Please point to anything I might be doing wrong.

> > I built the binaries from a linux host (per instructions) and transfered

> > them over to the machine running QNX Neutrino.

> >

> > I have Momentics running and I see that io-display is already running.

> > How if I just do:

> >

> > # ./owb http://www.google.com

> >

> > I get a

> >

> > gf_layer_attach() failed: no such process

> > GF init failed: are you running io-display

> >

> > so if I run

> >

> > io-display -dvid=0x8086,did=0x27ae

> >

> > and then run owb again, i get my scrambled display.

> >

> > Am I doing something incorrectly?

> >

> >

> >

> > _______________________________________________

> >

> > General

> > http://community.qnx.com/sf/go/post63490

>

>

post63575: Re: RE: RE: Error building web-browsers project in linux host

2010-08-19T16:09:13Z

This is the output of vsync

#vsync

Number of displays: 1

Display 0: 1680x1050, refresh = 60hz

Number of Layers: 4

gf_layer_atach() failed

Returning from main() with 1

and the output from egl-gears

#egl-gears

gf_layer_attach() failed

> Can you run "vsync" and "egl-gears" using your io-display settings? Or

> is the display scrambled for those as well?

>

> I would also try other screen resolutions in display.conf just to see if

> it's a timing issue.

>

> -----Original Message-----

> From: Jonathan Wong [mailto:community-noreply@qnx.com]

> Sent: Wednesday, August 18, 2010 5:40 PM

> To: general-web_browsers

> Subject: Re: RE: Error building web-browsers project in linux host

>

> Please point to anything I might be doing wrong.

> I built the binaries from a linux host (per instructions) and transfered

> them over to the machine running QNX Neutrino.

>

> I have Momentics running and I see that io-display is already running.

> How if I just do:

>

> # ./owb http://www.google.com

>

> I get a

>

> gf_layer_attach() failed: no such process

> GF init failed: are you running io-display

>

> so if I run

>

> io-display -dvid=0x8086,did=0x27ae

>

> and then run owb again, i get my scrambled display.

>

> Am I doing something incorrectly?

>

>

>

> _______________________________________________

>

> General

> http://community.qnx.com/sf/go/post63490

post63567: RE: RE: Error building web-browsers project in linux host

2010-08-19T15:42:16Z

Can you run "vsync" and "egl-gears" using your io-display settings? Or

is the display scrambled for those as well?

I would also try other screen resolutions in display.conf just to see if

it's a timing issue.

-----Original Message-----

From: Jonathan Wong [mailto:community-noreply@qnx.com]

Sent: Wednesday, August 18, 2010 5:40 PM

To: general-web_browsers

Subject: Re: RE: Error building web-browsers project in linux host

Please point to anything I might be doing wrong.

I built the binaries from a linux host (per instructions) and transfered

them over to the machine running QNX Neutrino.

I have Momentics running and I see that io-display is already running.

How if I just do:

# ./owb http://www.google.com

I get a

gf_layer_attach() failed: no such process

GF init failed: are you running io-display

so if I run

io-display -dvid=0x8086,did=0x27ae

and then run owb again, i get my scrambled display.

Am I doing something incorrectly?

_______________________________________________

General

http://community.qnx.com/sf/go/post63490

post63490: Re: RE: Error building web-browsers project in linux host

2010-08-18T21:39:59Z

Please point to anything I might be doing wrong.

I built the binaries from a linux host (per instructions) and transfered them over to the machine running QNX Neutrino.

I have Momentics running and I see that io-display is already running.

How if I just do:

# ./owb http://www.google.com

I get a

gf_layer_attach() failed: no such process

GF init failed: are you running io-display

so if I run

io-display -dvid=0x8086,did=0x27ae

and then run owb again, i get my scrambled display.

Am I doing something incorrectly?

post63482: Re: RE: Error building web-browsers project in linux host

2010-08-18T20:47:35Z

I don't see a graphics.conf but i do see a display.conf.

in it i see the list of my video card gma9xx (using intel chip with gma950 graphics)

and the correct display id:

drivername=gma9xx

modeopts=

vid=0x8086

did=0x27ae

device=0x0

display{

  xres=1680

  yres=1050

  refresh=60

  pixel_format=rgb565

  photon{

    enabled=1

    xoffset=0

    yoffset=0

    cursor=hardware

    input_group-1

   }

}

all these seem correct

Also I would like to use this when the system starts up so how can I work around the frame buffer issue if that is the case?

Thanks

Jon

> The io-display line looks ok. Check the /etc/system/config/graphics.conf

> file to make sure that the section for your vid/did combination has

> reasonable values for resolution, etc.

>

> If that is ok, then it may just be an uninitialized frame buffer you are

> seeing and running a gf app will fix things. Does the browser sample app

> work? (owb a.k.a. wklauncher)

>

> Max

>

> -----Original Message-----

> From: Jonathan Wong [mailto:community-noreply@qnx.com]

> Sent: Friday, August 13, 2010 7:08 PM

> To: general-web_browsers

> Subject: Re: Error building web-browsers project in linux host

>

> Hi All, I finally got the project to build properly

> but I am not quite understanding the last part

>

> Make sure io-display and an input driver are running:

> io-display -dvid=[vid],did=[did]

> devi-hid -P mouse kbd

>

> So I see this when I type:

> enum-devices -n

>

> mount -Tio-display vid=0x8086,did=0x27ae,deviceindex=0

>

> i put those two hex values like so

>

> # io-display -dvid=0x8086,did=0x27ae

>

>  and my display is scrambled.

>

> Is this not the correct way to do this?

>

>

>

>

> _______________________________________________

>

> General

> http://community.qnx.com/sf/go/post63012

post63021: RE: Error building web-browsers project in linux host

2010-08-15T02:47:27Z

The io-display line looks ok. Check the /etc/system/config/graphics.conf

file to make sure that the section for your vid/did combination has

reasonable values for resolution, etc.

If that is ok, then it may just be an uninitialized frame buffer you are

seeing and running a gf app will fix things. Does the browser sample app

work? (owb a.k.a. wklauncher)

Max

-----Original Message-----

From: Jonathan Wong [mailto:community-noreply@qnx.com]

Sent: Friday, August 13, 2010 7:08 PM

To: general-web_browsers

Subject: Re: Error building web-browsers project in linux host

Hi All, I finally got the project to build properly

but I am not quite understanding the last part

Make sure io-display and an input driver are running:

io-display -dvid=[vid],did=[did]

devi-hid -P mouse kbd

So I see this when I type:

enum-devices -n

mount -Tio-display vid=0x8086,did=0x27ae,deviceindex=0

i put those two hex values like so

# io-display -dvid=0x8086,did=0x27ae

and my display is scrambled.

Is this not the correct way to do this?

_______________________________________________

General

http://community.qnx.com/sf/go/post63012

post63012: Re: Error building web-browsers project in linux host

2010-08-13T23:07:59Z

Hi All, I finally got the project to build properly

but I am not quite understanding the last part

Make sure io-display and an input driver are running:

io-display -dvid=[vid],did=[did]

devi-hid -P mouse kbd

So I see this when I type:

enum-devices -n

mount -Tio-display vid=0x8086,did=0x27ae,deviceindex=0

i put those two hex values like so

# io-display -dvid=0x8086,did=0x27ae

and my display is scrambled.

Is this not the correct way to do this?

post62885: opengl es in qnx browser plugin

2010-08-13T02:25:26Z

I can successfully run opengl es demo in qnx-car head unit hardware and qnx GF drawings in qnx browser plugin. However, it seems that qnx browser webkit doesn't have native support on qnx opengl es in its plugin.

Does anyone know how to create opengl context in qnx browser plugin?

Thanks a lot.

post61656: Re: RE: Error building web-browsers project in linux host

2010-08-04T23:19:17Z

so it seems like i am having a stdio_ext.h does not exist error while running make owb.

I used locate stdio_ext.h to find it and it is under my /usr/include/ folder.

The error is as follows:

In file included from /home/jonathanccwong/ide-4.7-workspace/QNX-Web-Browsers/webkit/trunk/JavaScriptCore/AllInOneFile.cpp:47:

/home/jonathanccwong/ide-4.7-workspace/QNX-Web-Browsers/webkit/trunk/JavaScriptCore/runtime/Collector.cpp:98:23: error: stdio_ext.h: No such file or directory

In file included from /home/jonathanccwong/ide-4.7-workspace/QNX-Web-Browsers/webkit/trunk/JavaScriptCore/AllInOneFile.cpp:47:

/home/jonathanccwong/ide-4.7-workspace/QNX-Web-Browsers/webkit/trunk/JavaScriptCore/runtime/Collector.cpp: In function 'void* pthread_getattr_np(pthread_t, pthread_attr_t*)':

/home/jonathanccwong/ide-4.7-workspace/QNX-Web-Browsers/webkit/trunk/JavaScriptCore/runtime/Collector.cpp:128: error: 'FSETLOCKING_BYCALLER' was not declared in this scope

/home/jonathanccwong/ide-4.7-workspace/QNX-Web-Browsers/webkit/trunk/JavaScriptCore/runtime/Collector.cpp:128: error: '__fsetlocking' was not declared in this scope

/home/jonathanccwong/ide-4.7-workspace/QNX-Web-Browsers/webkit/trunk/JavaScriptCore/runtime/Collector.cpp:138: error: 'feof_unlocked' was not declared in this scope

/home/jonathanccwong/ide-4.7-workspace/QNX-Web-Browsers/webkit/trunk/JavaScriptCore/runtime/Collector.cpp:139: error: 'getdelim' was not declared in this scope

cc: /usr/qnx650/host/linux/x86//usr/lib/gcc/i486-pc-nto-qnx6.5.0/4.4.2/cc1plus error 1

make[3]: *** [JavaScriptCore/CMakeFiles/jsc.dir/AllInOneFile.cpp.o] Error 1

make[2]: *** [JavaScriptCore/CMakeFiles/jsc.dir/all] Error 2

make[1]: *** [WebKitTools/OWBLauncher/CMakeFiles/owb.dir/rule] Error 2

make: *** [owb] Error 2

Any help is greatly appreciated

jon

post61655: Re: RE: Error building web-browsers project in linux host

2010-08-04T23:00:35Z

wow, Thanks, it is compiling as we speak.

I linked crank at /root/opt/crank.3.3 rather than at /

Thanks

post61654: RE: Error building web-browsers project in linux host

2010-08-04T22:20:54Z

Did you unpack /opt/crank/ version 3.3 correctly?

-----Original Message-----

From: Jonathan Wong [mailto:community-noreply@qnx.com]

Sent: Wednesday, August 04, 2010 6:13 PM

To: general-web_browsers

Subject: Error building web-browsers project in linux host

Hi Everyone,

I recently checked out the web-browsers project to try and build the

browser for QNX.

I am running Ubuntu 10.04 as a host and following the directions in the

README.

I am stuck with this Error:

Could NOT find JPEG (missing: JPEG_LIBRARY JPEG_INCLUDE_DIR)

and I am not sure what is the cause of this.

Anyone know what I can do?

Thanks

Jon

_______________________________________________

General

http://community.qnx.com/sf/go/post61653

post61653: Error building web-browsers project in linux host

2010-08-04T22:13:22Z

Hi Everyone,

I recently checked out the web-browsers project to try and build the browser for QNX.

I am running Ubuntu 10.04 as a host and following the directions in the README.

I am stuck with this Error:

Could NOT find JPEG (missing: JPEG_LIBRARY JPEG_INCLUDE_DIR)

and I am not sure what is the cause of this.

Anyone know what I can do?

Thanks

Jon

post58606: RE: RE: Webkit source download fails

2010-07-05T23:12:47Z

Hi Andreas. It seems that the webkit source code was included in the

list of restricted source code. I'm not sure why this decision was made,

but more info on getting source access is here:

http://community.qnx.com/sf/wiki/do/viewPage/projects.community/wiki/Upd

atedQNXSourceAccessPolicyFAQ

Regards,

Max

-----Original Message-----

From: Andreas Lichtenberger [mailto:community-noreply@qnx.com]

Sent: Monday, July 05, 2010 7:19 AM

To: general-web_browsers

Subject: Re: RE: Webkit source download fails

I am still not able to download the source! Still with the same errors

_______________________________________________

General

http://community.qnx.com/sf/go/post58412

post58412: Re: RE: Webkit source download fails

2010-07-05T11:19:21Z

I am still not able to download the source! Still with the same errors

post58411: Re: RE: NPAPI

2010-07-05T11:17:01Z

So i ported basic parts of my plugin to qnx and tried to install it on the system.

because i am still not able to download the webkit source, i tried to make it run in the first step for the "Bob Echo" delivered with the system.

Plugin is not detected. So what can i do wrong here?

post58306: RE: NPAPI

2010-07-01T20:44:41Z

There is a very simple graphical sample plugin in the source code at:

webkit/trunk/WebCore/plugins/Gf/sample-plugin/

Also see the header "npapi.h", and the WebKit-side plugin code one level

up from the sample-plugin directory. In general the NPAPI is not browser

or OS specific except when it comes to graphics & window management,

i.e. the surface structure passed be WebKit for the plugin to render

into, or the management of the plugin's window if it renders into its

own window.

Another example of an NPAPI plugin is the JNEXT plugin at

http://jnext.org, which has been ported to QNX and is in the repository

under 3rdparty/trunk/jnext-1.0.8.3/. This plugin is non-graphical

therefore is more portable across browsers and OS's.

Regards,

Max

-----Original Message-----

From: Andreas Lichtenberger [mailto:community-noreply@qnx.com]

Sent: Wednesday, June 30, 2010 7:09 AM

To: general-web_browsers

Subject: NPAPI

I am totally new to QNX development and i need to port a NPAPI browser

plugin to QNX.

I need some starting help. Any howtos, examples, anything?

_______________________________________________

General

http://community.qnx.com/sf/go/post58169

post58305: RE: Webkit source download fails

2010-07-01T20:34:19Z

I have made you a member of the web-browsers project. I believe you will

be able to check out using SVN now.

Please be aware that the WebKit source in this repository has not been

maintained for several months now because work has shifted to an

internal repository that has more restricted access. There are many

advances in the internal repository which are not reflected in the

general repository.

For more information you can contact QNX customer service.

If you have technical questions you can continue to post here.

Regards,

Max

-----Original Message-----

From: Andreas Lichtenberger [mailto:community-noreply@qnx.com]

Sent: Thursday, July 01, 2010 8:17 AM

To: general-web_browsers

Subject: Webkit source download fails

Trying to checkout svn sources of the webkit gives me authorization

failed. I know that there are some restricted code areas but webkit

should not be part of this.

Why can i watch the source tree in my browser, but failing when trying

to checkout?

path is: /svn/repos/web-browsers/webkit/trunk/

Trying to checkout with: svn checkout --username <username> --password

<pass> http://community.qnx.com/svn/.....

Gives me: Authentication realm: <http://community.....:80> Authorisation

Realm

Username:

Can do this three times.....

Then:

svn: PROPFIND of 'svn/repos/...' : authorization failed

(http://community....)

Of cource the username is email addy from account registration and pass

is correspondending pass...

So please help...

_______________________________________________

General

http://community.qnx.com/sf/go/post58288

post58288: Webkit source download fails

2010-07-01T12:16:57Z

Trying to checkout svn sources of the webkit gives me authorization failed. I know that there are some restricted code areas but webkit should not be part of this.

Why can i watch the source tree in my browser, but failing when trying to checkout?

path is: /svn/repos/web-browsers/webkit/trunk/

Trying to checkout with: svn checkout --username <username> --password <pass> http://community.qnx.com/svn/.....

Gives me: Authentication realm: <http://community.....:80> Authorisation Realm

Username:

Can do this three times.....

Then:

svn: PROPFIND of 'svn/repos/...' : authorization failed (http://community....)

Of cource the username is email addy from account registration and pass is correspondending pass...

So please help...

post58169: NPAPI

2010-06-30T11:09:14Z

I am totally new to QNX development and i need to port a NPAPI browser plugin to QNX.

I need some starting help. Any howtos, examples, anything?

post57963: ICU build

2010-06-28T12:21:16Z

Hi All,

I am trying to compile ICU source on QNX 6.4.1.

I am encountering this error:

error: #error This version of XOPEN_SOURCE is not supported.

Any idea on this.

regards

Satish

post55652: Re: Porting of a web gui from QNX 6.3.2 to QNX 6.4.1 using Slinger Web Server

2010-05-27T11:58:03Z

Hi,

How are you?

I have a question.

I have same problem of you with slinger. have you solved the problem?

Can you answer me please it's for my graduate work and it's very important for me.

Thank you very much.

post55418: session expire with slinger server

2010-05-24T04:07:00Z

Hi,

Could you kindly let me know how to implement session expiration for a web page with slinger web server.

Ex: if a per closes web page by clicking on close button of window then how do I make page or session or login as expired.

Does slinger server has any env variables to keep track of it?

Regards

Sravanthy

post51435: RE: Cursor for wklauncher

2010-04-10T17:24:54Z

Hi Dennis. Wklauncher uses the gf_cursor_* routines. These may not be

supported with certain drivers, I'm not sure. Maybe re-ask this GF

related question in the Graphics project...

Max

-----Original Message-----

From: Dennis Kellly [mailto:community-noreply@qnx.com]

Sent: Friday, April 09, 2010 4:10 PM

To: general-web_browsers

Subject: Cursor for wklauncher

I am using an SDP CD installation on a desktop pc.  It is using vesabios

since no native driver is available.  If I start wklauncher, I get the

message "Could not set cursor".  The page loads  the status line at the

bottom indicates the mouse is moving over links (which work) but he

cursor is invisible.

I tried "hardware cursor" and "software" cursor.  Res is 1280x1024.

What is the requirement for a cursor with webkit?

_______________________________________________

General

http://community.qnx.com/sf/go/post51414

post51414: Cursor for wklauncher

2010-04-09T20:10:06Z

I am using an SDP CD installation on a desktop pc. It is using vesabios since no native driver is available. If I start wklauncher, I get the message "Could not set cursor". The page loads the status line at the bottom indicates the mouse is moving over links (which work) but he cursor is invisible.

I tried "hardware cursor" and "software" cursor. Res is 1280x1024.

What is the requirement for a cursor with webkit?

post51384: QNX Source Access Policy Update

2010-04-09T14:24:49Z

This message is to inform you that QNX Software Systems has updated its

source code access policy.

Although these changes affect a very limited number of QNX community

members, they do change the process of how source-code access is

granted.

Please refer to the FAQ

(http://community.qnx.com/sf/wiki/do/viewPage/projects.community/wiki/Up

datedQNXSourceAccessPolicyFAQ) for details.

Regards

QNX Community Management Group

post51224: RE: RE: SVG

2010-04-06T18:21:11Z

The Skia work is QNX driven, and will be part of the upcoming QNX Screen

project.

-----Original Message-----

From: Tomas Cervinka [mailto:community-noreply@qnx.com]

Sent: Tuesday, April 06, 2010 3:00 AM

To: general-web_browsers

Subject: Re: RE: SVG

Thanks for information Max,

this is great to hear. I'm thinking of a new application design:

-Control appl. C/C++

-Apache+FastCGI

-AJAX+HTML/SVG

so your WebKit port is an important part. Is it a QSS supported project

and will it be sometimes part of an official QNX release or is it just a

community work?

Tom

_______________________________________________

General

http://community.qnx.com/sf/go/post51186

post51186: Re: RE: SVG

2010-04-06T07:00:16Z

Thanks for information Max,

this is great to hear. I'm thinking of a new application design:

-Control appl. C/C++

-Apache+FastCGI

-AJAX+HTML/SVG

so your WebKit port is an important part. Is it a QSS supported project and will it be sometimes part of an official QNX release or is it just a community work?

Tom

post51104: RE: SVG

2010-04-02T15:12:32Z

SVG is not supported in the QNX port of WebKit. This is because GF does

not support enough of the drawing primitives needed, like a full

transformation matrix, path clipping, etc. The html canvas element is

often used with svg so I turned off the support of canvas as well. This

makes it easier for web sites to fall back to non-svg rendering. For

example the big "Telus" logo on www.telus.com.

We are working on a Skia based version of the QNX WebKit port (i.e. Skia

used instead of GF in the WebKit library) and it will soon be possible

to implement SVG support, but this has not been done yet. Canvas is

turned back on in this new version to support HTML5 canvas.

Regards,

Max

-----Original Message-----

From: Tomas Cervinka [mailto:community-noreply@qnx.com]

Sent: Friday, April 02, 2010 8:26 AM

To: general-web_browsers

Subject: SVG

Does someone have any idea about SVG support in WebKit QNX port??

_______________________________________________

General

http://community.qnx.com/sf/go/post51096

post51096: SVG

2010-04-02T12:25:43Z

Does someone have any idea about SVG support in WebKit QNX port??

post50973: Re: Porting of a web gui from QNX 6.3.2 to QNX 6.4.1 using Slinger Web Server

2010-03-31T15:48:36Z

Below there is a html page that call the C CGI Scripts example of the previous post:

<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">

<html>

<head>

    <meta http-equiv="Content-Type" content="text/html; charset=ISO-8859-1">

<META HTTP-EQUIV="pragma" CONTENT="no-cache">

    <meta name="Owner" content="PRISMA ENGINEERING S.r.l.">

    <meta name="Author" content="Riccardo ANNOLFI">

    <title>Archive : steroidi</title>

<script language="JavaScript">



</script>

</head>

<body>

  <a href="#" onClick="MM_openBrWindow('/cgi-bin/cgiTestSystemCall','cgiTestSystemCall','status=yes,scrollbars=no,resizable=no,width=450,height=245');"> clickMe </a>

</body>

</html>

Best regards.

Riccardo Annolfi

post50972: Porting of a web gui from QNX 6.3.2 to QNX 6.4.1 using Slinger Web Server

2010-03-31T15:33:04Z

Hi,

i'm making a porting of a web gui from QNX 6.3.2 to QNX 6.4.1 using Slinger Web Server and C CGI Scripts running on it and i've found a problem.

I'm not using the SSI token in the shtml files, but C programs (C CGI Scripts) that create dinamycally html pages.

Working on QNX 6.4.1 ,when i make a system() call, from a C CGI Scripts, the system launchs the command and executes it correctly, but the return value is -1 and the results of the command is displayed on the web window, while, on QNX 6.3.2 the return value is 0 and the results of the command is not displayed on the web window.

If the same C CGI Scripts is launched from command line, it works always correctly.

If i make change the user that execute the C CGI via Slinger, from Slinger user, that is root -2 (with uid 4294967294 ), to user.users, it fails the same.

While, from shell, if i execute it with Slinger user, setting uid at 4294967294, it works always correctly. So it seems that does not depends on the user.

The same happens if, instead of a system(), i use a spawn() or a spawnl() or a execl() or a execvp(). Also if i use a fork() with an execl(). If i test waitpid(), its return value is always -1.

The WIFEXITED(sysStatus) and WEXITSTATUS( sysStatus ) macros confirm the error, that is always: errno = 10 and strerror(errno)="No child processes".

I've implemented the QNX 6.4.1 system() code, calling it "mysystem()" and adding some logs inside to see what happens. I discovered that, when the QNX 6.4.1 system() tests the waitpid() return value, being it always -1, the system() returns always -1 too.

Analyzing it with "pidin fam sig" command, it seems that when i launch from Slinger a C CGI Scripts, with his own PID, and this C CGI Scripts 'spawns' a process, with his own PID, the parent-child relationship between them is no more present.

And so, the C CGI Scripts wrongly thinks that has no wait for any child processes.

How can i resolve this problem?

Below there is the Slinger launch command script:

/home/user/riccardoa# cat /etc/rc.d/rc.www

#!/bin/sh

#ifdef __USAGE

#

#%C

#

# It starts http server for this system

#

#endif

export HTTPD_ROOT_DIR=/lsu/www/current

export HTTPD_ROOT_DOC=index.html

export HTTPD_SCRIPTALIAS=/lsu/www/current/cgi

slay -Q slinger

slinger -d -c -e -s

# eof

Below there are the Slinger launch command script privileges:

/home/user/riccardoa# ls -la /etc/rc.d/rc.www

-rwxr-xr-x  1 root      root            253 Mar 16  2006 /etc/rc.d/rc.www

Below there is a simple C CGI Scripts example that works on QNX 6.3.2, but doesn't on QNX 6.4.1:

#include <string.h>

#include <stdlib.h>

#include <stdio.h>

#include <errno.h>

#include <sys/wait.h>

int main (int argc, char *argv[])

{

    int sysStatus = 0;

printf("Content-type: text/html;\n\n");

sysStatus = system( "/usr/bin/id " );

      if( sysStatus == -1 ) {

         printf( "\n" );

      } else {

         printf( "\n", WEXITSTATUS( sysStatus ) );

      }

return 0;

}

Below there are the C CGI Scripts example privileges:

-rwsr-sr-x  1 root      root           5255 Mar 31 18:00 cgiTestSystemCall-1.0

Best regards.

Riccardo Annolfi

post50703: Re: RE: Customizing wklauncher

2010-03-29T15:48:19Z

Thanks Max. May have to try the manual approach to setting up the headers (from qnx-car). Can't get the perl environment to work - and that's only to configure step...

post50700: RE: Customizing wklauncher

2010-03-29T15:26:25Z

Hi Dennis. The wklauncher (aka "owb") is integrated into the cmake based

webkit library build, builds alongside it with dependencies into the

build results directory structure, and ends up in the same build results

directory. One of its main purposes is to test the webkit library that

it gets built with. So as-is it does need to be built with all of

webkit.

If you want an example of a browser app that links against webkit but is

not part of the webkit build, see the webkit_kd launcher used for QNX

CAR. A copy of it can be found in the web-browsers source repository

under qnx/trunk/. It has a regular QNX recursive Makefile build

structure, but with dependencies to webkit libs and headers that you

must satisfy manually, for example by using symbolic links from a

staging directory to a webkit build.

So you're right that the entire webkit does not need to be built, but it

makes pulling in headers much easier if it has at least been configured

(which creates subdirectories of links to required headers).

Max

-----Original Message-----

From: Dennis Kellly [mailto:community-noreply@qnx.com]

Sent: Monday, March 29, 2010 10:45 AM

To: general-web_browsers

Subject: Customizing wklauncher

I need to build a custom version of wklauncher.  Since it links to

supplied binary shared libraries, there seems no logical reason why the

entire webkit should need to be built, but docs say it does .   (Kind of

like saying you need to build the o/s to compile 'hello world'...what am

I missing?)

There are two perl packages (one from crank) but the docs don't really

say what the relationship between them is - just that you need them.  I

have been unable satisfy perl 'include' requirements to get configure to

run without error.  Any hints?

Thanks,

Dennis

_______________________________________________

General

http://community.qnx.com/sf/go/post50697

post50697: Customizing wklauncher

2010-03-29T14:44:50Z

I need to build a custom version of wklauncher. Since it links to supplied binary shared libraries, there seems no logical reason why the entire webkit should need to be built, but docs say it does . (Kind of like saying you need to build the o/s to compile 'hello world'...what am I missing?)

There are two perl packages (one from crank) but the docs don't really say what the relationship between them is - just that you need them. I have been unable satisfy perl 'include' requirements to get configure to run without error. Any hints?

Thanks,

Dennis

post50060: browser.swf does not play in qnxcar

2010-03-19T23:13:43Z

Hi

I compiled the browser project from hmi_framework. After compilation, it creates a browser.swf file. I replace the browser.swf file in the qnx car with this one to test. The browser does not work. I see only white screen.

My question is the browser project in the hmi_framework is up to date or it needs certain files/configuration to make it work.

FYI: The browser.swf file can't be played locally or with flash player in the qnx car. my browser.swf file is attached.

I am using qnx car vmware.

Regards

--Ahsan

post49063: libpng build

2010-03-09T06:20:58Z

Hi ,

I am trying to build libpng on QNX 6.4.1 self hosted.

./configure is successful.

however make is throwing an error:

libtool: link: `0.33.0' is not valid version information

make[1]: *** [libpng12.la] Error 1

Any idea , why I am getting this error ?

Thanks,

Satish P

post48321: RE: RE: Webkit and PlugIns

2010-02-25T16:42:55Z

It is possible to call into a plugin using Javascript. You need to

create a mechanism to do this as part of your plugin. This is how the

jnext plugin works. See the web-browsers Foundry27 project home page

news item:

  "Javascript Native Extensions ported to QNX

  Do you want to invoke any local executable or interface to any native

functionality using

  Javascript on your WebPage? Then the Javascript Native Extensions

framework is what you need.

  The work done by http://www.jnext.org has been ported to QNX. The

source code is available

  here:

http://community.qnx.com/svn/repos/web-browsers/3rdparty/trunk/jnext-1.0

.8.3  "

Jnext is just an NPAPI based plugin with Javascript glue at the front

end. You could look into the source code and use some of the same ideas

in your plugin.

Max

-----Original Message-----

From: Heinrich Ziegenhagel [mailto:community-noreply@qnx.com]

Sent: Thursday, February 25, 2010 8:01 AM

To: general-web_browsers

Subject: Re: RE: Webkit and PlugIns

Hi,

thank you for you fast answer.

I had a look on the sample-plugin and it looks to me very similar like

the PlugIn I have made for Firefox (np_entry, npn_gate... are the same).

But I have still one question is it not posible to call PluginFunctions

via JavaScript. I "think" NetscapeAPI has the interface to call via

JavaScript functions from Plugin.

Example:

<object id="simpleplugin" type="application/simple-plugin"

class=hiddenObject></object><br>

<script>

var embedPlug = document.getElementById('simpleplugin');

function show(arg)

{

  document.getElementById("result").innerHTML += "<p>" +  arg + "</p>";

}

if (embedPlug)

{

  show("plug.version = " + embedPlug.version); 

}

Of course needs the Plugin to include the Java interface.

But maybe I am mixing this with extensions.

If I interpret you answer and the code of Webkit it means to me that it

is not posible to call functions via JavaScript form a Plugin

"Scriptable Plugin". Is it realy only posible to talk between Webkit and

Plugin with defined Functions in the NAPI like Mouseover, Mouseclik,

Loadurl.

Thank You!

_______________________________________________

General

http://community.qnx.com/sf/go/post48270

post48270: Re: RE: Webkit and PlugIns

2010-02-25T13:01:16Z

Hi,

thank you for you fast answer.

I had a look on the sample-plugin and it looks to me very similar like the PlugIn I have made for Firefox (np_entry, npn_gate... are the same). But I have still one question is it not posible to call PluginFunctions via JavaScript. I "think" NetscapeAPI has the interface to call via JavaScript functions from Plugin.

Example:

<object id="simpleplugin" type="application/simple-plugin" class=hiddenObject></object><br>

<script>

var embedPlug = document.getElementById('simpleplugin');

function show(arg)

{

  document.getElementById("result").innerHTML += "<p>" +  arg + "</p>";

}

if (embedPlug)

{

  show("plug.version = " + embedPlug.version); 

}

Of course needs the Plugin to include the Java interface.

But maybe I am mixing this with extensions.

If I interpret you answer and the code of Webkit it means to me that it is not posible to call functions via JavaScript form a Plugin "Scriptable Plugin". Is it realy only posible to talk between Webkit and Plugin with defined Functions in the NAPI like Mouseover, Mouseclik, Loadurl.

Thank You!

post48250: cairo build

2010-02-25T05:55:15Z

Hi,

I am trying to build cairo on QNX 6.4.1 self hosted.

I followed the following steps.

1. I built pixman 0.15.18 which is the dependency for cairo.

2. export PKG_CONFIG_PATH=/opt/pixman/lib/pkgconfig:/opt/crank/x86/lib/pkgconfig

3. export PATH=$PATH:/opt/crank/bin (pkg-config executable is there in this path)

4. After running ./configure : it is successful

5. However, when I am running make,

I am getting this linker errors

/usr/qnx641/host/qnx6/x86/usr/bin/ntox86-ld: cannot find -lz

collect2: ld returned 1 exit status

I am wondering why this error is comming..

Your inputs are appreciated.

Thanks,

Satish

post48197: RE: Webkit and PlugIns

2010-02-24T17:22:39Z

The QNX WebKit port supports the Netscape Plugin API (NPAPI). The set of

functions called is defined by the API.

For an example, see:

http://community.qnx.com/integration/viewvc/viewvc.cgi/webkit/trunk/WebC

ore/plugins/Gf/sample-plugin/?root=web-browsers&system=exsy1001

-----Original Message-----

From: Heinrich Ziegenhagel [mailto:community-noreply@qnx.com]

Sent: Wednesday, February 24, 2010 11:53 AM

To: general-web_browsers

Subject: Webkit and PlugIns

Hi everybody,

I am learning/trying to develop PlugIn for Webkit. And I have a problem,

Webkit loads/initialize the Plugin but don't calls the function of the

plugin. So I have tried something else. I build this Plugin for Firefox

Win32 there was needet to create an *.xpt File which has the information

what kind of funktions do the Plugin use and it has to go to the

usr/AplicationData/Mozilla/Plugins directory where also the shared *.dll

of Plugin are. Then the Plugin works and the Browser can handle with it

via JavaScript. Then I tryed it for Safary on Win32 and there I have the

same problem like with the Webkit on QNX.

The Plugin is loaded/initialized but no fuctions are called!

How can I let the Webkit know what kind of Functions does the Plugin

use/have, on QNX?

IfI call a function via JavaScript the return is always undefined.

Can any one help?

Thanks.

_______________________________________________

General

http://community.qnx.com/sf/go/post48194

post48194: Webkit and PlugIns

2010-02-24T16:52:56Z

Hi everybody,

I am learning/trying to develop PlugIn for Webkit. And I have a problem, Webkit loads/initialize the Plugin but don't calls the function of the plugin. So I have tried something else. I build this Plugin for Firefox Win32 there was needet to create an *.xpt File which has the information what kind of funktions do the Plugin use and it has to go to the usr/AplicationData/Mozilla/Plugins directory where also the shared *.dll of Plugin are. Then the Plugin works and the Browser can handle with it via JavaScript. Then I tryed it for Safary on Win32 and there I have the same problem like with the Webkit on QNX.

The Plugin is loaded/initialized but no fuctions are called!

How can I let the Webkit know what kind of Functions does the Plugin use/have, on QNX?

IfI call a function via JavaScript the return is always undefined.

Can any one help?

Thanks.

post47759: RE: RE: owb linker error

2010-02-19T14:48:21Z

If you are running out of memory at build time, you need to add more

memory to your build machine. The armle problem in the readme was a case

I encountered early on and occurred on the target.

-----Original Message-----

From: satish pattar [mailto:community-noreply@qnx.com]

Sent: Friday, February 19, 2010 8:22 AM

To: general-web_browsers

Subject: Re: RE: owb linker error

Hello Max,

owb README says:

Debugging on armle may only working by doing a release build

and changing O2 and O3 to O0 in the following files created by

configure:

flags.make (6 files, multiple occurences)

It doesn't say anything about x86 DEBUG build issue.

For me , release build for SDL build works fine & owb is also launching.

but for debug build Memory exhaust problem.

Is it some problem with my build ? or is it something else ?

Your inputs are appreciated.

Thanks

Satish P

_______________________________________________

General

http://community.qnx.com/sf/go/post47748

post47748: Re: RE: owb linker error

2010-02-19T13:21:43Z

Hello Max,

owb README says:

Debugging on armle may only working by doing a release build

and changing O2 and O3 to O0 in the following files created by configure:

flags.make (6 files, multiple occurences)

It doesn't say anything about x86 DEBUG build issue.

For me , release build for SDL build works fine & owb is also launching.

but for debug build Memory exhaust problem.

Is it some problem with my build ? or is it something else ?

Your inputs are appreciated.

Thanks

Satish P

post47486: Newbie needs hints regarding web server to display large amount of data

2010-02-17T12:02:26Z

Hi

I would like to create a web interface, where I can display a table of data, unknown length. Say e.g. that I would like to create a web interface to show sloginfo. I've been looking at slinger and the data server / qnxvar, but if its lots of data that I would like to display, this method seems like lots of work... :-) Any other way to do this? Also it would be nice, if it could be displayed in a table, where the data could be sorted after date, severity etc.

/Torben

post47114: Re: RE: owb launcher (SDLCAIRO graphics)

2010-02-11T12:43:53Z

Hi Max,

That's true that it is creating shared library instead of an executable.

I replaced this -shared , -fPIC from CMAKE_C_FLAGS & CMAKE_CXX_FLAGS.

by using:

string(REPLACE "-shared" "" CMAKE_C_FLAGS ${CMAKE_C_FLAGS})

Now I guess it is trying to create an executable. And in the final stage of linking it is searching for libph, libasound etc.which earlier was not happening(should be becuase of shared lib being created instead of an executable).

I linked ph & asound lirary.

But some how I am not able to figure out why I am getting this error:

undefined reference to `cairo_ft_scaled_font_unlock_face`

undefined reference to `cairo_ft_font_face_create_for_ft_face`

undefined reference to `cairo_ft_scaled_font_lock_face`

undefined reference to `cairo_ft_font_face_create_for_pattern`

I have cairo built with font backend set to freetype.

Thanks & regards

Satish Pattar

post47100: using of perl modules in perl script for slinger server not working

2010-02-11T10:35:11Z

Hi All,

In my perl script, i am using perl modules like DBI or Sys. When executed from command prompt script is working but when I run from web browser gettng following error "erro parsing CGI script HTTP header data".

Could any one help on this.

Folliwing is the script lines:

#!usr/bin/perl

use DBI;

...................

..................

I have installed DBI and DBD perl modules.

In the script if i remove "use DBI;" then the script executes from web browser.

I have also mention path of modules in the script with follwing line

use lib "/root/localperl/site_perl/5.10.1/_x86_no"

Adding this also giving the same error.

Thanks

Sravanthy

post47049: RE: RE: RE: RE: OWB in VMware

2010-02-10T17:43:14Z

Are you running io-display? Also, make sure owb is run as root.

Max

-----Original Message-----

From: satish pattar [mailto:community-noreply@qnx.com]

Sent: Wednesday, February 10, 2010 4:00 AM

To: general-web_browsers

Subject: Re: RE: RE: RE: OWB in VMware

Hello,

On launching owb, I am getting the following error:

#./owb http://www.google.com

gf_dev_attach() failed: No such file or directory

GF init failed: are you running io-display?

#

Even vsync also throwing the same error.

what am I doing wrong ?

Thanks & Regards

Satish

_______________________________________________

General

http://community.qnx.com/sf/go/post47003

post47048: RE: owb launcher (SDLCAIRO graphics)

2010-02-10T17:41:50Z

Check the linker options being used to build your owb. For some reason

ld is producing a shared object instead of a regular executable.

To see the full commands lines used to compile and link, set the VERBOSE

environment variable. For example:

# VERBOSE=1 make owb

-----Original Message-----

From: satish pattar [mailto:community-noreply@qnx.com]

Sent: Wednesday, February 10, 2010 6:27 AM

To: general-web_browsers

Subject: owb launcher (SDLCAIRO graphics)

Hello,

I have built the OWB for SDLCAIRO graphics on QNX neutrino self hosted .

But when I try to run the application is not launching & immediately

returning to prompt.

what could be the reason ?

#./owb http://www.google.com

/bin/sh: ./owb: Attempting to exec a shared lib

#

Thanks

Satish P

_______________________________________________

General

http://community.qnx.com/sf/go/post47008

post47008: owb launcher (SDLCAIRO graphics)

2010-02-10T11:27:04Z

Hello,

I have built the OWB for SDLCAIRO graphics on QNX neutrino self hosted . But when I try to run the application is not launching & immediately returning to prompt.

what could be the reason ?

#./owb http://www.google.com

/bin/sh: ./owb: Attempting to exec a shared lib

#

Thanks

Satish P

post47003: Re: RE: RE: RE: OWB in VMware

2010-02-10T09:00:00Z

Hello,

On launching owb, I am getting the following error:

#./owb http://www.google.com

gf_dev_attach() failed: No such file or directory

GF init failed: are you running io-display?

#

Even vsync also throwing the same error.

what am I doing wrong ?

Thanks & Regards

Satish

post46806: RE: owb linker error

2010-02-08T16:48:18Z

In case anybody is interested, the problem was not enough memory

installed on the build machine. The README with the build instructions

gives some guidance on this.

Regards,

Max

-----Original Message-----

From: satish pattar [mailto:community-noreply@qnx.com]

Sent: Monday, February 08, 2010 4:29 AM

To: general-web_browsers

Subject: Re: owb linker error

Hi,

I got rid of this error after turning off the DEBUG flag.

Thanks

Satish P

_______________________________________________

General

http://community.qnx.com/sf/go/post46745

post46745: Re: owb linker error

2010-02-08T09:29:28Z

Hi,

I got rid of this error after turning off the DEBUG flag.

Thanks

Satish P

post46474: Re: running perl script file through slinger web server on QNX6.3

2010-02-03T17:19:04Z

Hi,

My perl is in /usr/bin/perl

And at command line the script is executed.

Thanks

Sravanthy

> Anyway, try to run the script on the command line first. And check that you have perl in right place according to your

> script (#!/usr/local/bin/perl)

>

>

>

> _______________________________________________

>

> General

> http://community.qnx.com/sf/go/post46446

>

>

Confidentiality Notice

The information contained in this electronic message and any

attachments to this message are intended for the exclusive use of

the addressee(s) and may contain confidential or privileged

information. If you are not the intended recipient, please notify

the sender at Bharat Electronics or support@bel.co.in immediately

and destroy all copies of this message and any attachments.

post46451: owb linker error

2010-02-03T13:58:45Z

I am trying to build the latest OWB for SDL CAIRO surface instead of GF on QNX . I could build wtf ,Javacore & WebCore.

When I build for target owb target. I am getting the linker error as mentioned below. Do you have any comment on this linker error ?

#make owb

[0%] Built target wtf

[7%] Built target jsc

[96%] Built target webcore

Linking CXX shared library ../../lib/libwebkit-owb.so

/usr/qnx641/host/qnx6/x86/usr/bin/ntox86-ld: failed to set dynamic section sizes: Memory exhausted

cc: /usr/qnx641/host/qnx6/x86/usr/bin/ntox86-ld error 1

make[3]: *** [lib/libwebkit-owb.so.2.0] Error 1

make[2]: *** [WebKit/OrigynWebBrowser/CMakeFiles/webkit-owb.dir/all] Error 2

make[1]: *** [WebKitTools/OWBLauncher/CMakeFiles/owb.dir/rule] Error 2

make: *** [owb] Error 2

#

-satish

post46446: Re: running perl script file through slinger web server on QNX6.3

2010-02-03T09:29:21Z

Anyway, try to run the script on the command line first. And check that you have perl in right place according to your script (#!/usr/local/bin/perl)

post46445: Re: running perl script file through slinger web server on QNX6.3

2010-02-03T09:25:50Z

I know it's a little bit too simple, but has the script execution attribute?

post46444: running perl script file through slinger web server on QNX6.3

2010-02-03T09:17:20Z

Following is my requirement:

I have to develop a web application ( to be on windows) to communicate an application running on QNX6.3.

QNX has slinger web server that supports CGI perl, SSI and DataServer

I am using CGI perl for scripting

For validating input data from html file (GUI) I am using perl script.

Issue: the perl script called from html file is not executing. The html page is prompting to save the .pl file which

is specified in html file.

Below is the proceedure I have followed:

exported following env variables-

export CMD_INT=/usr/bin/perl

export HTTPD_ROOT_DIR=/usr/htmldoc

export HTTPD_ROOT_DOC=Login.html

export HTTPD_SCRIPTALIAS=/usr/cig-bin

slinger -p 8080 &

then opened voyager browser with http://localhost:8080/ -- This opens Login.html.

But when password entered and login button is clicked, a download file dlg is displayed to save the perl script file.

This testing i am doing on local host.

I am attaching the html and .pl file for your reference.

Kindly let me know if you have any solution for this at the earliest.

If possible you could also provide be alternate solution how to go about with web application.

post44982: RE: RE: RE: OWB in VMware

2010-01-12T04:54:24Z

Sorry about the delay in responding. The steps you are taking look

correct. Things to check:

1) You indicate that you are getting a partial display, i.e. the simple

gui buttons show up. This means that your problem might not be the same

as Tomas', because he was not getting any display. Are you using VMware

like he is? If so, then it may be the same problem he had: Newer

versions of VMware need an updated Neutrino VMware graphics driver. I

have attached one to this email you can try.

2) Make sure that only one devi-hid is running. When you boot Neutrino

if you exit photon the devi-hid used by Photon may still be running.

3) I notice that you are getting the "Could not set cursor" message.

This indicates that the gf_cursor_set() call is failing. I'm not sure

why it would be failing, but you can try passing the -C option to owb

which makes it not attempt to draw the mouse pointer.

4) When you run "owb" are all the shared libraries being found and

opened correctly? To get this information, run owb with the DL_DEBUG

environment variable set, for example:

# DL_DEBUG=1 ./owb http://www.google.com

If this does not solve your problem, please send me the output of "pidin

arg" and a copy of your display.conf file.

Regards,

Max

-----Original Message-----

From: satish pattar [mailto:community-noreply@qnx.com]

Sent: Thursday, December 24, 2009 5:32 AM

To: general-web_browsers

Subject: Re: RE: RE: OWB in VMware

Hi,

I am also facing the same issue. is this issue resolved. ? I am trying

out this on QNX 6.4.1 self hosted.

Steps I have followed.

I downloaded the latest version of OWB webkit from SVN sources.

With the steps given in README , I could build the webkit.

Later I followed the pre-inquisitive instructions given in the README

I ran the display driver with display.conf file.

I ran devi-hid -P mouse kbd

After running, I am getting black screen with partial display.

Where am I doing wrong ?

your inputs are appreciated.

Thanks

Satish P.

--

Hello Max Feil,

I got your e-mail ID in QNX forum , I have already posted this issue on

QNX "web browser" discussion forum.

Just mailing you direclty if you could help me resolve this at the

earliest.

The issue:

On launching OWB browser with some valid url, the system is gettng hung

& I am seeing a partial web browser (with some buttons at the bottom)

& a black screen displaying some text which goes like this

#./owb http://www.google.com

Window w 1024, height 768

Could not set cursor

Steps I followed:

1> I compiled OWB from latest SVN sources on QNX Neutrino 6.4.1(Self

hosted)

2> ran graphics driver with display.conf which has the vendor & device

ID for display matching with the output of "pci".

3> Then I ran "devi-hid -P mouse kbd"

Am I missing any steps ?

Your inputs are appriciated.

Thanks & Regards

Sateesh Pattar

_______________________________________________

General

http://community.qnx.com/sf/go/post44400

post44400: Re: RE: RE: OWB in VMware

2009-12-24T10:31:44Z

Hi,

I am also facing the same issue. is this issue resolved. ? I am trying out this on QNX 6.4.1 self hosted.

Steps I have followed.

I downloaded the latest version of OWB webkit from SVN sources.

With the steps given in README , I could build the webkit.

Later I followed the pre-inquisitive instructions given in the README

I ran the display driver with display.conf file.

I ran devi-hid -P mouse kbd

After running, I am getting black screen with partial display.

Where am I doing wrong ?

your inputs are appreciated.

Thanks

Satish P.

post42045: Re: webkit_kd launcher

2009-11-16T21:24:03Z

The webkit_kd source code has been reinstated.

post42016: RE: webkit_kd launcher

2009-11-16T15:19:15Z

I updated the wiki page with a link for internal users. It was decided

that external users should have access only by request.

Thanks,

Max

-----Original Message-----

From: Peter Weber [mailto:community-noreply@qnx.com]

Sent: Monday, November 16, 2009 9:00 AM

To: general-web_browsers

Subject: webkit_kd launcher

Hi there,

where could we get the webkit_kd launcher source code?

The link on the wiki page points to an empty /trunk.

http://community.qnx.com/svn/repos/web-browsers/qnx/trunk/webkit_kd/

cheers,

Peter

_______________________________________________

General

http://community.qnx.com/sf/go/post42000

post42000: webkit_kd launcher

2009-11-16T13:59:39Z

Hi there,

where could we get the webkit_kd launcher source code?

The link on the wiki page points to an empty /trunk.

http://community.qnx.com/svn/repos/web-browsers/qnx/trunk/webkit_kd/

cheers,

Peter

post41769: RE: RE: OWB in VMware

2009-11-11T15:02:22Z

Can you email me directly at mfeil@qnx.com?

What is the contents of your /etc/system/config/display.conf file?

Are you able to run other gf apps like egl-gears?

-----Original Message-----

From: Tomas Cervinka [mailto:community-noreply@qnx.com]

Sent: Wednesday, November 11, 2009 9:52 AM

To: general-web_browsers

Subject: Re: RE: OWB in VMware

Sure, the input "problem" was caused by not correct starting of

devi-hid, but still black output.

My starting script is something like this:

export

LD_LIBRARY_PATH=$LD_LIBRARY_PATH:/opt/crank/x86/lib:/root/workspace/web-

browsers/webkit/trunk/nto-x86-gf/lib

io-display -dvid=0x15ad,did=0x405

/usr/photon/bin/devi-hid -P mouse kbd

/root/workspace/web-browsers/webkit/trunk/nto-x86-gf/bin/owb -d

and the output of owb is as follows:

Window w 1024, height 768

NOTIFY: Start loading http://www.google.com/

NOTIFY: Status:

NOTIFY: Status:

NOTIFY: Title: Google

NOTIFY: Progress : 29

NOTIFY: Progress : 36

NOTIFY: Progress : 45

NOTIFY: Progress : 50

NOTIFY: Progress : 63

Default Callbacks: Input Method State set to 1

NOTIFY: Progress : 67

NOTIFY: Progress : 100

NOTIFY: Finished loading http://www.google.cz/

NOTIFY: Hover: :http://video.google.cz/?hl=cs&tab=wv

NOTIFY: Hover: :http://maps.google.cz/maps?hl=cs&tab=wl

NOTIFY: Hover: NA:NA

NOTIFY: Tooltip: Vyhledat Googlem

Default Callbacks: Text field end edit

Default Callbacks: save view state for item 809b0e0

_______________________________________________

General

http://community.qnx.com/sf/go/post41766

post41766: Re: RE: OWB in VMware

2009-11-11T14:51:55Z

Sure, the input "problem" was caused by not correct starting of devi-hid, but still black output.

My starting script is something like this:

export LD_LIBRARY_PATH=$LD_LIBRARY_PATH:/opt/crank/x86/lib:/root/workspace/web-browsers/webkit/trunk/nto-x86-gf/lib

io-display -dvid=0x15ad,did=0x405

/usr/photon/bin/devi-hid -P mouse kbd

/root/workspace/web-browsers/webkit/trunk/nto-x86-gf/bin/owb -d

and the output of owb is as follows:

Window w 1024, height 768

NOTIFY: Start loading http://www.google.com/

NOTIFY: Status:

NOTIFY: Status:

NOTIFY: Title: Google

NOTIFY: Progress : 29

NOTIFY: Progress : 36

NOTIFY: Progress : 45

NOTIFY: Progress : 50

NOTIFY: Progress : 63

Default Callbacks: Input Method State set to 1

NOTIFY: Progress : 67

NOTIFY: Progress : 100

NOTIFY: Finished loading http://www.google.cz/

NOTIFY: Hover: :http://video.google.cz/?hl=cs&tab=wv

NOTIFY: Hover: :http://maps.google.cz/maps?hl=cs&tab=wl

NOTIFY: Hover: NA:NA

NOTIFY: Tooltip: Vyhledat Googlem

Default Callbacks: Text field end edit

Default Callbacks: save view state for item 809b0e0

post41764: RE: OWB in VMware

2009-11-11T14:40:07Z

Can you send the text from the console where you invoked wklauncher?

Showing:

- How you ran io-display, devi-hid, wklauncher.

- How you set up LD_LIBRARY_PATH

- Any messages from wklauncher

- Anything else relevant

-----Original Message-----

From: Tomas Cervinka [mailto:community-noreply@qnx.com]

Sent: Wednesday, November 11, 2009 6:56 AM

To: general-web_browsers

Subject: OWB in VMware

I compiled OWB from latest SVN sources in 6.4.1 SDP installed in VMware

image. When I run it with valid URL, the page gets loaded, but there is

nothing displayed - black screen only with UI and mouse cursor is dead

(works well under Photon). And No input available after I close it. Any

ideas? Thanks.

_______________________________________________

General

http://community.qnx.com/sf/go/post41752

post41752: OWB in VMware

2009-11-11T11:56:24Z

I compiled OWB from latest SVN sources in 6.4.1 SDP installed in VMware image. When I run it with valid URL, the page gets loaded, but there is nothing displayed - black screen only with UI and mouse cursor is dead (works well under Photon). And No input available after I close it. Any ideas? Thanks.