http://community.qnx.com/sf/discussion/do/listTopics/projects.qfc/discussion.general Posts for QFC Installation and build http://community.qnx.com/sf/go/post117145 Hello, I am a student and I am working on QNX for performing HIL and SIL Simnulations. I ordered new system to install QNX as RTOS. My system is Dell Precision Tower 3620 with following configurations: i7 Quad Core Processor 16GB RAM 1 TB HDD When I tried to install QNX with installation CD from boot menu, it asked me to apply driver update disk? F1 = Apply and F2 = Abort. The process stops here. When I tried to install it on other system (Dell Vostro), I was able to install QNX from installation CD successfully. Can I know what is the problem to install on Dell Precision Tower? And what is the proper solution for it? I am attaching screenshot of the problem I am facing while installing QNX on Precision Tower 3620. Thank You, Waiting for your response ASAP. Hitesh Ukani Fri, 18 Nov 2016 17:19:10 GMT http://community.qnx.com/sf/go/post117145 Hitesh Ukani(deleted) 2016-11-18T17:19:10Z http://community.qnx.com/sf/go/post114597 Is it possible to build a program using qcc from SDP 6.6 for 6.4.1? I have already tried several ways and still have a problem with libcpp.so.5. I can build successfully on my window host computer but when I executed the program on qnx target, it printed: "Could not load library libcpp.so.5". I think I should change the target version using -v in qcc command. I have tried some combinations but they don't work. Could anyone give me any suggestions? Thank you in advance. Wed, 07 Oct 2015 10:29:36 GMT http://community.qnx.com/sf/go/post114597 Piyapat Saranrittichai(deleted) 2015-10-07T10:29:36Z http://community.qnx.com/sf/go/post85555 Is it possible to use QFC on 6.5 ? thanks, Ran Tue, 10 May 2011 16:20:31 GMT http://community.qnx.com/sf/go/post85555 ran wainstein 2011-05-10T16:20:31Z http://community.qnx.com/sf/go/post19312 Have the following 'warning' message for the following projects: 'No active build configurations defined. All existing configurations will be built.' Cli, Guardian, Ramdisk, SatTest, Serv, TPool, Thrs, testAP Under right-click of Cli project, Build Configurations/Set Active, the active configuration is ntox86-gcc-3.3.5-debug, with ntox86-gcc-3.3.5-release and ntox86-gcc-4.2.3-release. Folders ntox86-gcc-3.3.5-debug and notx86-gcc-3.3.5-release are created for Cli project. Here's the output of the build. **** Clean-only build of configuration ntox86-gcc-3.3.5-debug for project Cli **** make clean rm -rf ./Cli.o ./main.o ./Cli.d ./main.d Cli_g **** Build of configuration ntox86-gcc-3.3.5-debug for project Cli **** make all Building file: ../Cli.cpp Invoking: QCC Compiler qcc -o Cli.o ../Cli.cpp -V3.3.5,gcc_ntox86_cpp -w1 -I"C:\QNX_QFC\sigc++\public" -I"C:\QNX_QFC\QFC\public" -I"C:\QNX_QFC\Serv" -c -g -Wc,-Wno-parentheses -Wp,-MMD,Cli.d -Wp,-MT,Cli.o cc: unknown target 'gcc_ntox86_cpp+debug' cc: no targets defined in /3.3.5! make: *** [Cli.o] Error 1 Fri, 02 Jan 2009 16:19:33 GMT http://community.qnx.com/sf/go/post19312 Keith Smith 2009-01-02T16:19:33Z http://community.qnx.com/sf/go/post16947 I'v successfuly install subversion and checked out QFC into my workspace. But I can't build the whole project. I found there is no '.cdtbuild ' file in sigc++ dirctory and QFC dirctory. please help! Thanks Thu, 20 Nov 2008 03:33:29 GMT http://community.qnx.com/sf/go/post16947 shen xifeng 2008-11-20T03:33:29Z http://community.qnx.com/sf/go/post13352 Yes, thanks. I have only developed servers with this library, and as such priority manipulation has not been required (servers always inherit priority). I have committed your patch with a minor name change (nice thing about C++ namespaces, is that there is no need to create mangled names for types). Fri, 12 Sep 2008 16:28:40 GMT http://community.qnx.com/sf/go/post13352 Rennie Allen 2008-09-12T16:28:40Z http://community.qnx.com/sf/go/post13319 Thanks. A timertree is indeed sufficient for now. I have another question. As far as I can see it is not possible to create a Thread and let it run on a specific priority? I've included a patch which should add that to PosixAPI::Thread. Haven't tested it yet, but I will test it soon. It also fixes the docgen.Doxyfile for the QFC project. Fri, 12 Sep 2008 12:33:58 GMT http://community.qnx.com/sf/go/post13319 Bart Veldhuijzen 2008-09-12T12:33:58Z http://community.qnx.com/sf/go/post13260 SETIOV is defined in unistd.h (which is included in the example Serv.h). I have added unistd.h to ipc; thanks for pointing this out. Are you sure you want a timerbank as opposed to a timertree? A timerbank is a priority vector of timertrees (i.e. 255 timertrees, with callbacks from each tree executing at the associated priority). If you are just trying out the interface, a timertree may be sufficient. Thu, 11 Sep 2008 16:58:02 GMT http://community.qnx.com/sf/go/post13260 Rennie Allen 2008-09-11T16:58:02Z http://community.qnx.com/sf/go/post13236 Thanks, Serv does compile now. When I try to instantiate the TimerBank myself, I get the following error: /home/veldhuijzen/workspace/QFC/public/qfc/ipc:697: error: 'SETIOV' was not declared in this scope I guess I'm missing something here. I just want a timerbank and add some timed callbacks to it. Can you give some hints on how to proceed? Thu, 11 Sep 2008 09:54:32 GMT http://community.qnx.com/sf/go/post13236 Bart Veldhuijzen 2008-09-11T09:54:32Z http://community.qnx.com/sf/go/post13220 Norton, Sorry for the delayed response, I have been traveling a lot through July and August. Doxygen does build for nto (as Mario mentions), and the plug-ins should work. If the "find & install" is not working for you, then you can just download eclox and unzip in the plugins directory. I haven't tried it, but it is java, and should just work... Rennie Wed, 10 Sep 2008 21:39:30 GMT http://community.qnx.com/sf/go/post13220 Rennie Allen 2008-09-10T21:39:30Z http://community.qnx.com/sf/go/post13214 Actually, I tried switching the compiler on Serv to 4.2.3, and I see exactly the same problem. There is a bug in the Cancel() method of TimerBank which I have fixed and committed. If you update QFC from the repository it should work now. Wed, 10 Sep 2008 20:49:27 GMT http://community.qnx.com/sf/go/post13214 Rennie Allen 2008-09-10T20:49:27Z http://community.qnx.com/sf/go/post13211 Hmmm, It works fine for me (IDE 4.5 gcc 4.2.3 & gcc 3.3.5). Do you have gcc 3.3.5 available on your system (as this is the compiler defined in the project for Serv by default)? Could you post the entire output from the console window when you try to build. Wed, 10 Sep 2008 20:20:43 GMT http://community.qnx.com/sf/go/post13211 Rennie Allen 2008-09-10T20:20:43Z http://community.qnx.com/sf/go/post13199 > I'm just trying out QFC. I'm an educational user, and I was forced to choose > either Neutrino or Windows for my development environment and went with > Neutrino. This may be an IDE question, but is it possible to install the > Doxygen plugins under Neutrino? At the moment the "Find and Install..." option > does not even give me a dialog, so that approach doesn't appear to work for > anything. I did my svn checkout from the command line for lack of a subversion > plugin. I'm wondering if I'll have to do builds under Neutrino and generate > documentation under a generic Eclipse install on Windows. You can build doxygen for Neutrino (I'm using 1.5.1). However it's not a plug-in. It will have to be added to the makefile or manually invoked. The IDE under Neutrino is *really* slow. Until QNX find a way to speed it up I personnaly feel that for any serious project it's unusable. Wed, 10 Sep 2008 19:28:33 GMT http://community.qnx.com/sf/go/post13199 Mario Charest 2008-09-10T19:28:33Z http://community.qnx.com/sf/go/post13137 Hi, I can't get my projects to compile properly when I try to include part of the QFC. For example, just including <qfc/timerbank> generates compiler errors: /home/veldhuijzen/ide-4.5-workspace/QFC/public/qfc/timerbank: In member function 'void QNXAPI::TimerBank<T, V, R>::Cancel(QNXAPI::TimerTree::TimerNode*, sigc::slot<bool, sigc::nil, sigc::nil, sigc::nil, sigc::nil, sigc::nil, sigc::nil, sigc::nil>)': /home/veldhuijzen/ide-4.5-workspace/QFC/public/qfc/timerbank:127: error: 'priority' was not declared in this scope /home/veldhuijzen/ide-4.5-workspace/QFC/public/qfc/timerbank:131: error: request for member 'Cancel' in 'iter->second', which is of non-class type 'QNXAPI::TimerTree*' This also happens when I try to compile the Serv example. I am using QDE 4.5, and QNX 6.4.0 with gcc 4.2.4. Any hints on how to solve these problems? Further there are some warnings about deprecated conversions from string constant to 'char*'. Wed, 10 Sep 2008 09:51:56 GMT http://community.qnx.com/sf/go/post13137 Bart Veldhuijzen 2008-09-10T09:51:56Z http://community.qnx.com/sf/go/post9781 I'm just trying out QFC. I'm an educational user, and I was forced to choose either Neutrino or Windows for my development environment and went with Neutrino. This may be an IDE question, but is it possible to install the Doxygen plugins under Neutrino? At the moment the "Find and Install..." option does not even give me a dialog, so that approach doesn't appear to work for anything. I did my svn checkout from the command line for lack of a subversion plugin. I'm wondering if I'll have to do builds under Neutrino and generate documentation under a generic Eclipse install on Windows. Fri, 27 Jun 2008 14:37:28 GMT http://community.qnx.com/sf/go/post9781 Norton Allen 2008-06-27T14:37:28Z http://community.qnx.com/sf/go/post9633 Hmmm, I got the Hot Eclox as well, but it worked for me. I am running the latest Momentics (ver 4.5 available here on F27) but AFAIK, it is still based on eclipse 3.2. Anyway, glad it is working for you. Have you installed dot as well? Tue, 24 Jun 2008 21:52:41 GMT http://community.qnx.com/sf/go/post9633 Rennie Allen 2008-06-24T21:52:41Z http://community.qnx.com/sf/go/post9632 I found the problem. I had gotten the Hot Eclox plug-in. This plug-in is only for 3.3 and higher. Momentics is 3.2. Disabled Hot Eclox and now I can properly click on .doxyfiles. Tue, 24 Jun 2008 21:16:00 GMT http://community.qnx.com/sf/go/post9632 Keith Smith 2008-06-24T21:16:00Z http://community.qnx.com/sf/go/post9608 BTW: I am preparing a major upgrade to QFC, that includes: 1. A dynamic plug-in class (i.e. a factory container that allows you to simply invoke a class constructor; under the covers this class will load the appropriate DLL, using a user supplied method to turn class name into a file name). 2. An adaptive partitioning class, that provides a basic framework for programmatic control/monitoring of temporal partitions. 3. A SAT class that takes care of a lot of the trickiness of dynamic tracing. Look for an announcement on the project page around the middle of July... Tue, 24 Jun 2008 16:49:21 GMT http://community.qnx.com/sf/go/post9608 Rennie Allen 2008-06-24T16:49:21Z http://community.qnx.com/sf/go/post9603 Keith, I just tried installing Eclox from the link in your post, and it worked fine for me. After installation, I double-clicked on docgen.Doxyfile in the project "Ramdisk", and it opened the correct Eclox editor. Did you restart eclipse after installing? Tue, 24 Jun 2008 16:17:10 GMT http://community.qnx.com/sf/go/post9603 Rennie Allen 2008-06-24T16:17:10Z http://community.qnx.com/sf/go/post9558 After obtaining the QFC files from the repository following the directions at: http://community.qnx.com/sf/projects/qfc and obtaining my plug-in of Eclox from http://download.gna.org/eclox/update I get the following message when I click on a Doxyfile. "Unable to create this part due to an internal error. Reason for the failure: The editor class could not be instantiated. This usually indicates that the editor's class name was mistyped in plugin.xml." What do I do next to correct this problem? Keith Tue, 24 Jun 2008 12:32:29 GMT http://community.qnx.com/sf/go/post9558 Keith Smith 2008-06-24T12:32:29Z http://community.qnx.com/sf/go/post5037 Rennie, I overwrote the existing copies of those libraries in /lib on the target (just to make sure), and got the same behavior. I do not recall putting copies of those libraries anywhere else on the target. Gordon -----Original Message----- From: Rennie Allen [mailto:rallen@qnx.com] Sent: Thursday, February 14, 2008 10:13 AM To: install-qfc Subject: Re: RE: RE: Build failure Gordon, Did you copy libsigc++ and libqfc to /lib? Are there any other copies of these libraries potentially on the path? _______________________________________________ QFC Installation and build http://community.qnx.com/sf/go/post5033 - CONFIDENTIAL- This email and any files transmitted with it are confidential, and may also be legally privileged. If you are not the intended recipient, you may not review, use, copy, or distribute this message. If you receive this email in error, please notify the sender immediately by reply email and then delete this email. Thu, 14 Feb 2008 18:39:00 GMT http://community.qnx.com/sf/go/post5037 Gordon Molek 2008-02-14T18:39:00Z http://community.qnx.com/sf/go/post5033 Gordon, Did you copy libsigc++ and libqfc to /lib? Are there any other copies of these libraries potentially on the path? Thu, 14 Feb 2008 16:13:19 GMT http://community.qnx.com/sf/go/post5033 Rennie Allen 2008-02-14T16:13:19Z http://community.qnx.com/sf/go/post4845 Rennie, I downloaded Ramdisk_g to /sbin and ran it with the same results. Here's the result of my "set" command. ABLANG=en_US ABLPATH=/usr/photon/translations DISPLAY=127.1:0 FONTSLEUTH=/dev/fontsleuthctrl HOME=/root HOSTNAME=localhost IFS=' ' KSH_VERSION='@(#)PD KSH v5.2.14 99/07/13.2' LD_LIBRARY_PATH=/proc/boot:/lib:/usr/lib:/lib/dll:/opt/lib:/Zebra/lib:/u sr/photon/lib:/usr/photon/dll:/usr/local/lib:/opt/X11R6/lib:/usr/X11R6/l ib:/Zebra/lib LOGNAME=root MAILCHECK=600 MAKEFLAGS=-I/usr/qnx632/target/qnx6/usr/include OLDPWD=/Parser OPTIND=1 PATH=/sbin:/usr/sbin:/bin:/usr/bin:/usr/photon/bin:/usr/photon/appbuilde r:/opt/X11R6/bin:/usr/X11R6/bin:/usr/local/bin:/opt/bin:/opt/sbin:/usr/q nx632/host/qnx6/x86/usr/bin:/usr/qnx632/host/qnx6/x86/usr/sbin:/usr/qnx6 32/host/qnx6/x86/sbin:/usr/qnx632/host/qnx6/x86/bin:/usr/qnx632/host/qnx 6/x86/usr/photon/appbuilder PHFONT=/dev/phfont PHINSTANCE=1 PHOTON=/dev/photon PHOTON2_PATH=/usr/photon PHOTON_PATH=/usr/photon PHSTART=1 PHTK_PATH=/usr/photon PHWM=pwm PPID=561191 PROCESSOR=x86 PS1='# ' PS2='> ' PS3='#? ' PS4='+ ' PWD=/ QNX_CONFIGURATION=/etc/qnx QNX_HELP_HOME_PAGE=/usr/qnx632/target/qnx6/usr/help/product/momentics/bo okset.html QNX_HELP_PATH=/usr/qnx632/target/qnx6/usr/help/product QNX_HOST=/usr/qnx632/host/qnx6/x86 QNX_TARGET=/usr/qnx632/target/qnx6 RANDOM=15580 SECONDS=15488 SHELL=/bin/sh SYSNAME=nto TERM=qansi-m TMOUT=0 TMPDIR=/tmp USER_NAME=/dev/photon _=set -----Original Message----- From: Rennie Allen [mailto:rallen@qnx.com] Sent: Wednesday, February 06, 2008 11:59 AM To: install-qfc Subject: Re: RE: Build failure > Rennie, > Thanks for the response. I did a fresh check-out, fixed the libsigc++ > include file reference problem, downloaded libsigc-2.0_g.so and > libqfc_g.so to /lib on the target and ran Ramdisk_g from within > Momentics, setting its argument to the mount point "/ramdisk". It > seems to run and I can do an "ls -l /ramdisk" which returns an empty > directory, but when I attempt to copy a file into the /ramdisk > directory I get the error message "Can't open destination file. (/ramdisk/foo): > Resource temporarily unavailable" Could you try running Ramdisk by copying it to the target and launching from the command line? The IDE may have a different path, and might be picking up an old library. Also, from the shell could you execute: # set and post the results? Thanks, > Thanks, > > Gordon Molek > > -----Original Message----- > From: Rennie Allen [mailto:rallen@qnx.com] > Sent: Monday, February 04, 2008 1:04 PM > To: install-qfc > Subject: Re: Build failure > > I Gordon, > > Sorry, I thought I had responded. The fact that you have list > corruption implies a build error. > > Could you clean the library, re-build and download to target, and then > rebuild Ramdisk and try again? > > I have tried it here (from the repository) and it works fine for me. > > Thanks, > > Rennie > > > _______________________________________________ > QFC Installation and build > http://community.qnx.com/sf/go/post4781 > > - CONFIDENTIAL- > This email and any files transmitted with it are confidential, and may > also be legally privileged. If you are not the intended recipient, > you may not review, use, copy, or distribute this message. If you > receive this email in error, please notify the sender immediately by > reply email and then delete this email. _______________________________________________ QFC Installation and build http://community.qnx.com/sf/go/post4842 - CONFIDENTIAL- This email and any files transmitted with it are confidential, and may also be legally privileged. If you are not the intended recipient, you may not review, use, copy, or distribute this message. If you receive this email in error, please notify the sender immediately by reply email and then delete this email. Wed, 06 Feb 2008 19:31:43 GMT http://community.qnx.com/sf/go/post4845 Gordon Molek 2008-02-06T19:31:43Z http://community.qnx.com/sf/go/post4844 When I do a run-as->qconn c/c++ the debugger can not find the libraries and symbols. If I copy the executable, and run it on the targer (Vmware) it works fine. Might I need to copy the header files to the vmware target as well in order to get debugging working? The library is build with debugging symbols on btw. Wed, 06 Feb 2008 18:43:42 GMT http://community.qnx.com/sf/go/post4844 Jeffry Molanus 2008-02-06T18:43:42Z http://community.qnx.com/sf/go/post4843 Jeffry, what are the symptoms? (debug works fine for me). What version of the IDE/tools are you using? For C++ I definitely recommend getting the TAU build of the IDE, and the gcc 4.2 preview. The C++ support in gcc 4.2 is much better than earlier compilers... Wed, 06 Feb 2008 18:02:02 GMT http://community.qnx.com/sf/go/post4843 Rennie Allen 2008-02-06T18:02:02Z http://community.qnx.com/sf/go/post4842 > Rennie, > Thanks for the response. I did a fresh check-out, fixed the libsigc++ > include file reference problem, downloaded libsigc-2.0_g.so and > libqfc_g.so to /lib on the target and ran Ramdisk_g from within > Momentics, setting its argument to the mount point "/ramdisk". It seems > to run and I can do an "ls -l /ramdisk" which returns an empty > directory, but when I attempt to copy a file into the /ramdisk directory > I get the error message "Can't open destination file. (/ramdisk/foo): > Resource temporarily unavailable" Could you try running Ramdisk by copying it to the target and launching from the command line? The IDE may have a different path, and might be picking up an old library. Also, from the shell could you execute: # set and post the results? Thanks, > Thanks, > > Gordon Molek > > -----Original Message----- > From: Rennie Allen [mailto:rallen@qnx.com] > Sent: Monday, February 04, 2008 1:04 PM > To: install-qfc > Subject: Re: Build failure > > I Gordon, > > Sorry, I thought I had responded. The fact that you have list > corruption implies a build error. > > Could you clean the library, re-build and download to target, and then > rebuild Ramdisk and try again? > > I have tried it here (from the repository) and it works fine for me. > > Thanks, > > Rennie > > > _______________________________________________ > QFC Installation and build > http://community.qnx.com/sf/go/post4781 > > - CONFIDENTIAL- > This email and any files transmitted with it are confidential, and may also be > legally privileged. If you are not the intended recipient, you may not > review, use, copy, or distribute this message. If you receive this email in > error, please notify the sender immediately by reply email and then delete > this email. Wed, 06 Feb 2008 17:58:29 GMT http://community.qnx.com/sf/go/post4842 Rennie Allen 2008-02-06T17:58:29Z http://community.qnx.com/sf/go/post4841 Doing a remote debug with qconn etc, still doesnt work... any fix for that? Wed, 06 Feb 2008 17:56:39 GMT http://community.qnx.com/sf/go/post4841 Jeffry Molanus 2008-02-06T17:56:39Z http://community.qnx.com/sf/go/post4839 Thanks for the quick reply. I'm looking forward to use QFC for codegeneration of CSP based control models. Jeffry Wed, 06 Feb 2008 17:20:28 GMT http://community.qnx.com/sf/go/post4839 Jeffry Molanus 2008-02-06T17:20:28Z http://community.qnx.com/sf/go/post4838 > Hi, > > Once I have build the libqfc, how do I 'deploy' it to the target? I've got a > vmware machine running, but it cant find the libqfc_g.so. Hi Jeffry, To "deploy" qfc, onto VMWare, you simply need to use the IDE's "Target File System Navigator" to drag&drop both libqfc[_g].so and libsigc-2.0.so into either the "/lib" or "/usr/lib" (whatever your personal preference is) directories. That should do it... Wed, 06 Feb 2008 17:00:19 GMT http://community.qnx.com/sf/go/post4838 Rennie Allen 2008-02-06T17:00:19Z http://community.qnx.com/sf/go/post4837 Rennie, Thanks for the response. I did a fresh check-out, fixed the libsigc++ include file reference problem, downloaded libsigc-2.0_g.so and libqfc_g.so to /lib on the target and ran Ramdisk_g from within Momentics, setting its argument to the mount point "/ramdisk". It seems to run and I can do an "ls -l /ramdisk" which returns an empty directory, but when I attempt to copy a file into the /ramdisk directory I get the error message "Can't open destination file. (/ramdisk/foo): Resource temporarily unavailable" Thanks, Gordon Molek -----Original Message----- From: Rennie Allen [mailto:rallen@qnx.com] Sent: Monday, February 04, 2008 1:04 PM To: install-qfc Subject: Re: Build failure I Gordon, Sorry, I thought I had responded. The fact that you have list corruption implies a build error. Could you clean the library, re-build and download to target, and then rebuild Ramdisk and try again? I have tried it here (from the repository) and it works fine for me. Thanks, Rennie _______________________________________________ QFC Installation and build http://community.qnx.com/sf/go/post4781 - CONFIDENTIAL- This email and any files transmitted with it are confidential, and may also be legally privileged. If you are not the intended recipient, you may not review, use, copy, or distribute this message. If you receive this email in error, please notify the sender immediately by reply email and then delete this email. Wed, 06 Feb 2008 16:58:23 GMT http://community.qnx.com/sf/go/post4837 Gordon Molek 2008-02-06T16:58:23Z http://community.qnx.com/sf/go/post4836 Hi, Once I have build the libqfc, how do I 'deploy' it to the target? I've got a vmware machine running, but it cant find the libqfc_g.so. Wed, 06 Feb 2008 16:55:38 GMT http://community.qnx.com/sf/go/post4836 Jeffry Molanus 2008-02-06T16:55:38Z http://community.qnx.com/sf/go/post4781 I Gordon, Sorry, I thought I had responded. The fact that you have list corruption implies a build error. Could you clean the library, re-build and download to target, and then rebuild Ramdisk and try again? I have tried it here (from the repository) and it works fine for me. Thanks, Rennie Mon, 04 Feb 2008 19:04:08 GMT http://community.qnx.com/sf/go/post4781 Rennie Allen 2008-02-04T19:04:08Z http://community.qnx.com/sf/go/post4104 Ok, I figured it out (I think). Here you go. #0 0xb0320668 in _list_release () from /usr/qnx632/target/qnx6/x86/lib/libc.so.2 #1 0xb0320f41 in __prelocked_free () from /usr/qnx632/target/qnx6/x86/lib/libc.so.2 #2 0xb0320ff0 in __free () from /usr/qnx632/target/qnx6/x86/lib/libc.so.2 #3 0xb031ea4e in free () from /usr/qnx632/target/qnx6/x86/lib/libc.so.2 #4 0xb82fd351 in operator delete(void*) () from /usr/qnx632/target/qnx6/x86/lib/libcpp.so.4 #5 0xb82911e9 in ~Node (this=0x80476cc) at node.cpp:519 #6 0xb8293651 in ~Ocb (this=0x80596a0) at ocb.cpp:122 #7 0xb82661f8 in QNXAPI::Resmgr::DispatchCloseOcb(_resmgr_context*, void*, ocb* ) (this=0x80477c4, ctp=0x8059738, reserved=0x0, ocb=0x80596f8) at resmgr.cpp:801 #8 0xb8263180 in QNXAPI::CloseRedir(_resmgr_context*, void*, ocb*) ( ctp=0x8059738, msg=0x0, ocb=0x80596f8) at resmgr.cpp:155 #9 0xb033785c in _resmgr_close_handler () from /usr/qnx632/target/qnx6/x86/lib/libc.so.2 #10 0xb0337aa8 in _resmgr_connect_handler () from /usr/qnx632/target/qnx6/x86/lib/libc.so.2 #11 0xb0338db5 in _resmgr_handler () from /usr/qnx632/target/qnx6/x86/lib/libc.so.2 #12 0xb032a432 in resmgr_handler () from /usr/qnx632/target/qnx6/x86/lib/libc.so.2 #13 0xb826854c in QNXAPI::Resmgr::ResmgrIoSelector::BlockContext(_resmgr_context *) (this=0x8047a10, context=0x8059738) at resmgr.cpp:1251 #14 0xb82829d7 in sigc::bound_mem_functor1<void, QNXAPI::Resmgr::ResmgrIoSelecto r, _resmgr_context*>::operator()(_resmgr_context* const&) const ( this=0x804d29c, _A_a1=@0x80475bc) at functors/mem_fun.h:1851 #15 0xb828295f in operator()<resmgr_context_t* const&> (this=0x804d298, _A_arg1=@0x80475bc) at adaptor_trait.h:84 #16 0xb8282931 in sigc::internal::slot_call1<sigc::bound_mem_functor1<void, QNXA PI::Resmgr::ResmgrIoSelector, _resmgr_context*>, void, _resmgr_context*>::call_i t(sigc::internal::slot_rep*, _resmgr_context* const&) (rep=0x804d280, a_1=@0x80475bc) at functors/slot.h:136 #17 0xb8282df5 in sigc::internal::signal_emit1<void, _resmgr_context*, sigc::nil >::emit(sigc::internal::signal_impl*, _resmgr_context* const&) ( impl=0x804b398, _A_a1=@0x80475bc) at signal.h:686 #18 0xb826ba3a in sigc::signal1<void, _resmgr_context*, sigc::nil>::emit(_resmgr _context* const&) const (this=0x8047a2c, _A_a1=@0x80475bc) at signal.h:1812 #19 0xb826b5c5 in QNXAPI::IoSelector<_resmgr_context>::Block() (this=0x8047a10) at ioselector:447 #20 0xb8268827 in QNXAPI::Resmgr::Run(sigc::slot<bool, int, sigc::nil, sigc::nil , sigc::nil, sigc::nil, sigc::nil, sigc::nil>) (this=0x80477c4, loopControl= {<slot1<bool,int>> = {<slot_base> = {<functor_base> = {<No data fields >}, rep_ = 0x804d4b0, blocked_ = false}, <No data fields>}, <No data fields>}) at resmgr.cpp:1288 #21 0xb82685e4 in QNXAPI::Resmgr::Run() (this=0x80477c4) at resmgr.cpp:1267 #22 0x0804911d in main (argc=2, argv=0x8047a6c) at main.cpp:38 Mon, 07 Jan 2008 19:40:12 GMT http://community.qnx.com/sf/go/post4104 Gordon Molek 2008-01-07T19:40:12Z http://community.qnx.com/sf/go/post4102 Rennie, I would be happy to provide a backtrace if you can provide me with instructions on how to do so (I am new to QNX). Thanks regarding the "Monitor" button. I wasn't looking for it at that level of the forums. Gordon Mon, 07 Jan 2008 19:23:31 GMT http://community.qnx.com/sf/go/post4102 Gordon Molek 2008-01-07T19:23:31Z http://community.qnx.com/sf/go/post4092 Gordon, Are saying you started Ramdisk like so: # Ramdisk /ramdisk ? If so then this should work. Can you get a back-trace from gdb? You can certainly get notification of posts, by clicking on the "monitor" button for the forum. Thanks, Rennie Mon, 07 Jan 2008 17:16:13 GMT http://community.qnx.com/sf/go/post4092 Rennie Allen 2008-01-07T17:16:13Z http://community.qnx.com/sf/go/post4079 > Hi Gordon, > > What is your command line invocation for Ramdisk? > > It requires a single argument (which is the mountpoint of the ramdisk). Since > it is intended as example code, the error handling of detecting a NULL argv[0 > ] is omitted... > > Thanks, > > Rennie Rennie, In the "Arguments" tab of the "Open Launch Config" pane reached via "Run As->C/C++ QNX Conn" menu I simply but "/ramdisk". Did you mean to say "argv[1]" as isn't argv[0] the programe's name, supplied by the fork/exec? Also, is there any way to set up my account to receive e-mail notification when a post in made to the forum? Thanks, Gordon Mon, 07 Jan 2008 12:57:30 GMT http://community.qnx.com/sf/go/post4079 Gordon Molek 2008-01-07T12:57:30Z http://community.qnx.com/sf/go/post4025 Hi Gordon, What is your command line invocation for Ramdisk? It requires a single argument (which is the mountpoint of the ramdisk). Since it is intended as example code, the error handling of detecting a NULL argv[0] is omitted... Thanks, Rennie Thu, 03 Jan 2008 02:45:55 GMT http://community.qnx.com/sf/go/post4025 Rennie Allen 2008-01-03T02:45:55Z http://community.qnx.com/sf/go/post3991 Rennie, Thanks, now we can build. I've attempted to run the RAM disk example. I've copied the libsigc-2.0_g.so and libqfc_g.so libraries to the target and placed them in /lib. The RAM disk application runs and is receive blocked until I attempt to do anything signficant to it, e.g., ls -l /mount-point, cd /mount-point, etc., at which point it terminates. Running in the debugger doesn't help much as I don't know how to set it up yet to see all the necessary source (I only see the main() source for the ram disk application. Thanks, Gordon Molek Thu, 27 Dec 2007 13:23:25 GMT http://community.qnx.com/sf/go/post3991 Gordon Molek 2007-12-27T13:23:25Z http://community.qnx.com/sf/go/post3917 > Hello, > I'm attempting to build QFC for the first time and when I attempt to build > sigc++ I get errors in signal.h > > 33: typedef size_t size_type; - ISO C++ forbids declaration > 34: typedef ptrdiff_t difference_type - ISO C++ forbids declaration > > and similarly in signal_base.h > > 45: typedef size_t size_type; - ISO C++ fobids declaration > > I am running Momemtics Version: 4.0.1 Build id: I20070321 > > Thanks in advance, > > Gordon Molek > Zebra Technologies Corporation Hi Gordon, This is an error on my part (sorry). Momentics base directory used to be QNX630, but it is now QNX632. Here is how to fix this. 1. right-click on the "sigc++" project and then select "properties". 2. on the properties dialog select "C/C++ build" 3. on the "configuration" drop-down, select the build target (unfortunately, the following steps need to be performed for each build target) 4. once you have the desired build target selected, then under "QCC Compiler", select the "General" item 5. you should now see a text field titled "Other Options"; in this field change all references to QNX630 to QNX632 That should do it. I'll update this in the next few days. Thanks for pointing this out! Wed, 19 Dec 2007 15:49:35 GMT http://community.qnx.com/sf/go/post3917 Rennie Allen 2007-12-19T15:49:35Z http://community.qnx.com/sf/go/post3901 Hello, I'm attempting to build QFC for the first time and when I attempt to build sigc++ I get errors in signal.h 33: typedef size_t size_type; - ISO C++ forbids declaration 34: typedef ptrdiff_t difference_type - ISO C++ forbids declaration and similarly in signal_base.h 45: typedef size_t size_type; - ISO C++ fobids declaration I am running Momemtics Version: 4.0.1 Build id: I20070321 Thanks in advance, Gordon Molek Zebra Technologies Corporation Wed, 19 Dec 2007 14:10:59 GMT http://community.qnx.com/sf/go/post3901 Gordon Molek 2007-12-19T14:10:59Z