Feed for discussion QNX4 Community Support (EOL) in project Community.
http://community.qnx.com/sf/discussion/do/listTopics/projects.community/discussion.qnx4_community_support
Posts for QNX4 Community Support (EOL)post122385: Virtual image created for VmWare with GUI not booting
http://community.qnx.com/sf/go/post122385
We are using QNX sdp 7.1 and momentics ide to create a virtual target for vmware with an addition argument --graphics=yes to load the gfx libraries. This image doesnt boot completely and is stuck in a black screen. I have attached images. VMware Workstation 17 player is used.Mutyala Jagadeesh Babu2023-10-10T09:49:29Zpost121957: Re: Question about ls and the ln column
http://community.qnx.com/sf/go/post121957
Oh, and the fs is a qnx6 if that matters.Adrian Hawryluk2022-10-12T20:05:53Zpost121956: Question about ls and the ln column
http://community.qnx.com/sf/go/post121956
I was exploring the qnx environment when I noticed that ls's ln field for directories was >1. I thought that was strange and I attempted to find where the other link was. I used find's -inode and a combination of find, xargs, ls, sort and awk for good measure. Turns out there wasn't any.
So my question is, what is the ln field representing for a directory?
Thx.Adrian Hawryluk2022-10-12T20:05:12Zpost121743: Re: qnx4.25 linking error: unreference function statfs()
http://community.qnx.com/sf/go/post121743
This should be solved by adding the unix3r library.
For example, file test.c
#include <sys/statfs.h>
#include <stdio.h>
int main(void){
struct statfs buffer;
int ret;
ret = statfs("/", &buffer, 0, 0);
return 0;
}
can be compiled with the next command:
# cc test.c -lunix3r -o testMartin Walter2022-03-02T13:39:39Zpost121742: Re: qnx4.25 linking error: unreference function statfs()
http://community.qnx.com/sf/go/post121742
what library you have linked your binary against?
Show the compiler line please.Peter Weber2022-03-01T09:55:55Zpost121736: qnx4.25 linking error: unreference function statfs()
http://community.qnx.com/sf/go/post121736
Hi everyone,
I have got a problem with statfs() function. When compiling, it issued an error: undefined symbol statfs_
I have included header file:
#include <sys/statfs.h>
How can I resolve this ?Cong Pham(deleted)2022-02-23T09:57:02Zpost121627: unable to acess /dev/hd0
http://community.qnx.com/sf/go/post121627
I am trying to install QNX 6.3.0 on PC
PC is equipped with SATA hard disk (1 tb )with 7th gen mother board and I3 6th gen processor.
It is able to load the software version and application while booting in routine mode it shows this error
unable to acess "/dev/hdo"(2)
mount : can't mount /(type qnx4)
mount : possible reason : no such device or address
unable to start "mount" (2)
unable to start "ksh"(2)
Quires
1. Software version 6.3 is compactable with 7th gen mother board and I3 6th gen processor, if so how to resolve above error
2. If it not compatible which processor and mother board can be used
Kindly quide
Thanks in advance
Anu Mohan MAnu mohan m(deleted)2021-10-16T07:51:26Zpost121606: Unable to install AWS CLI or SDK on QNS OS 6.5.0
http://community.qnx.com/sf/go/post121606
Hi Team,
I am unable to install AWS CLI or SDK on QNS OS 6.5.0.
The curl command is not working in Terminal. And unable to download from Internet.
Please guide.
ThanksSaurabh D(deleted)2021-10-01T07:24:00Zpost121109: Re: What printer does QNX4.25 support ?
http://community.qnx.com/sf/go/post121109
Hi Cong,
> Does anyone sugguest me how to print Cyrillic font via a serial-port printer ?
I guess you're printing raw plain text directly to serial port or via lpd. In this case the printer should have Cyrillic font support in your printer.
Respectfully,
Oleg
> Thank for reply
>
> I had used HP laser printer connected via USB 2.0 cable.
> io-usb &
> devu-usbprn &
>
> Everything was printed fine. But now I have new problem with serial port Epson
> CQ300 printer. It can print English characters only, but can't print Cyrillic
> ones.
> P/s: The document has been viewed fine because of installing fully Cyrillic
> font support.
>
> Does anyone sugguest me how to print Cyrillic font via a serial-port printer ?
> We have some serial-port printers installed, We are not allowed to install
> new USB one :'(Oleg Bolshakov2020-11-19T12:45:32Zpost121107: Re: What printer does QNX4.25 support ?
http://community.qnx.com/sf/go/post121107
Thank for reply
I had used HP laser printer connected via USB 2.0 cable.
io-usb &
devu-usbprn &
Everything was printed fine. But now I have new problem with serial port Epson CQ300 printer. It can print English characters only, but can't print Cyrillic ones.
P/s: The document has been viewed fine because of installing fully Cyrillic font support.
Does anyone sugguest me how to print Cyrillic font via a serial-port printer ? We have some serial-port printers installed, We are not allowed to install new USB one :'(Cong Pham(deleted)2020-11-19T07:33:01Zpost121101: Re: What printer does QNX4.25 support ?
http://community.qnx.com/sf/go/post121101
As far as I know laser-jet and usb 2.0 printer doesn't support QNX 4.25. I know that monochrome printer supports. I had to do the same thing as you. I was thinking of doing this at work. But I didn't succeed (at work I have a printer from the company Canon). I came home and tried to do the same on my printer. And I did it. I have a monochrome laser printer. From the company Brother. You can click here
https://www.mrdepot.ca/collections/brother-toner-cartridges and learn more about this printer. So I think that only a monochrome printer can help you print this type of information.Una Springer(deleted)2020-11-13T13:52:19Zpost121100: Re: What printer does QNX4.25 support ?
http://community.qnx.com/sf/go/post121100
As far as I know laser-jet and usb 2.0 printer doesn't support QNX 4.25. I know that monochrome printer supports. I had to do the same thing as you. I was thinking of doing this at work. But I didn't succeed (at work I have a printer from the company Canon). I came home and tried to do the same on my printer. And I did it. I have a monochrome laser printer. From the company Brother. You can [url=https://www.mrdepot.ca/collections/brother-toner-cartridges]click here[/url] and learn more about this printer. So I think that only a monochrome printer can help you print this type of information.Una Springer(deleted)2020-11-13T13:45:48Zpost121099: Re: What printer does QNX4.25 support ?
http://community.qnx.com/sf/go/post121099
I know that a Canon printer can do anythingVirginia Berry(deleted)2020-11-13T13:31:14Zpost120830: Re: Not able to find libc function while
http://community.qnx.com/sf/go/post120830
Hello!
This is discussion board for QNX 4 RTOS. Please post your question in discussion board for QNX 7 product.
Respectfully,
Oleg
> I have cross compiled gRPC (v1.27.3) for QNX 7 (ARM) platform. I am using the
> protobuf which was already available for our system (QNX ARM v3.11.4).
>
> After compiling it generated the binaries. I copied these binaries in our code
> to compile the application for QNX.
> We are using cmake to compile QNX runtime code.
>
> While compiling QNX I am getting this issue:
> ../../lib/libQAic.so: undefined reference to `inet_pton(int, char const*, void
> *)'
> ../../lib/libQAic.so: undefined reference to `gai_strerror(int)'
> ../../lib/libQAic.so: undefined reference to `clock_gettime(int, timespec*)'
> ../../lib/libQAic.so: undefined reference to `fcntl(int, int, ...)'
> ../../lib/libQAic.so: undefined reference to `unsetenv(char const*)'
> ../../lib/libQAic.so: undefined reference to `setenv(char const*, char const*,
> int)'
> ../../lib/libQAic.so: undefined reference to `nanosleep(timespec const*,
> timespec*)'
> ../../lib/libQAic.so: undefined reference to `stat(char const*, stat*)'
> ../../lib/libQAic.so: undefined reference to `pthread_cond_timedwait(_sync*,
> _sync*, timespec const*)'
> ../../lib/libQAic.so: undefined reference to `read(int, void*, unsigned long)'
>
> ../../lib/libQAic.so: undefined reference to `inet_ntop(int, void const*, char
> *, unsigned int)'
> ../../lib/libQAic.so: undefined reference to `pipe(int*)'
> ../../lib/libQAic.so: undefined reference to `write(int, void const*, unsigned
> long)'
> ../../lib/libQAic.so: undefined reference to `unlink(char const*)'
> ../../lib/libQAic.so: undefined reference to `close(int)'
> ../../lib/libQAic.so: undefined reference to `sysconf(int)'
> ../../lib/libQAic.so: undefined reference to `getaddrinfo(char const*, char
> const*, addrinfo const*, addrinfo**)'
> ../../lib/libQAic.so: undefined reference to `freeaddrinfo(addrinfo*)'
> collect2: error: ld returned 1 exit status
> test/kmd/CMakeFiles/qaic_json_test.dir/build.make:117: recipe for target 'test
> /kmd/qaic_json_test' failed
> make[2]: *** [test/kmd/qaic_json_test] Error 1
> CMakeFiles/Makefile2:1012: recipe for target 'test/kmd/CMakeFiles/
> qaic_json_test.dir/all' failed
> make[1]: *** [test/kmd/CMakeFiles/qaic_json_test.dir/all] Error 2
> make[1]: *** Waiting for unfinished jobs....
>
> These all functions are already in libc. But they are not able to find it. The
> path is already included in environment variable, where libc is available.
> But still did not able to find it.
>
> Can anybody help me on this?
>Oleg Bolshakov2020-07-09T12:01:03Zpost120829: Not able to find libc function while
http://community.qnx.com/sf/go/post120829
I have cross compiled gRPC (v1.27.3) for QNX 7 (ARM) platform. I am using the protobuf which was already available for our system (QNX ARM v3.11.4).
After compiling it generated the binaries. I copied these binaries in our code to compile the application for QNX.
We are using cmake to compile QNX runtime code.
While compiling QNX I am getting this issue:
../../lib/libQAic.so: undefined reference to `inet_pton(int, char const*, void*)'
../../lib/libQAic.so: undefined reference to `gai_strerror(int)'
../../lib/libQAic.so: undefined reference to `clock_gettime(int, timespec*)'
../../lib/libQAic.so: undefined reference to `fcntl(int, int, ...)'
../../lib/libQAic.so: undefined reference to `unsetenv(char const*)'
../../lib/libQAic.so: undefined reference to `setenv(char const*, char const*, int)'
../../lib/libQAic.so: undefined reference to `nanosleep(timespec const*, timespec*)'
../../lib/libQAic.so: undefined reference to `stat(char const*, stat*)'
../../lib/libQAic.so: undefined reference to `pthread_cond_timedwait(_sync*, _sync*, timespec const*)'
../../lib/libQAic.so: undefined reference to `read(int, void*, unsigned long)'
../../lib/libQAic.so: undefined reference to `inet_ntop(int, void const*, char*, unsigned int)'
../../lib/libQAic.so: undefined reference to `pipe(int*)'
../../lib/libQAic.so: undefined reference to `write(int, void const*, unsigned long)'
../../lib/libQAic.so: undefined reference to `unlink(char const*)'
../../lib/libQAic.so: undefined reference to `close(int)'
../../lib/libQAic.so: undefined reference to `sysconf(int)'
../../lib/libQAic.so: undefined reference to `getaddrinfo(char const*, char const*, addrinfo const*, addrinfo**)'
../../lib/libQAic.so: undefined reference to `freeaddrinfo(addrinfo*)'
collect2: error: ld returned 1 exit status
test/kmd/CMakeFiles/qaic_json_test.dir/build.make:117: recipe for target 'test/kmd/qaic_json_test' failed
make[2]: *** [test/kmd/qaic_json_test] Error 1
CMakeFiles/Makefile2:1012: recipe for target 'test/kmd/CMakeFiles/qaic_json_test.dir/all' failed
make[1]: *** [test/kmd/CMakeFiles/qaic_json_test.dir/all] Error 2
make[1]: *** Waiting for unfinished jobs....
These all functions are already in libc. But they are not able to find it. The path is already included in environment variable, where libc is available. But still did not able to find it.
Can anybody help me on this?Darshan B(deleted)2020-07-09T11:31:40Zpost120079: Virtiualized QNX 4 & PhinX Video Issue
http://community.qnx.com/sf/go/post120079
Dear all,
please anyone had this issue before..?
Thanks, best regardsAlejandro Gonzalez2019-11-06T18:27:36Zpost120051: Re: Test suite to validate QNX
http://community.qnx.com/sf/go/post120051
As I've mentioned in my previous message, I don't know such solutions. I've meant that you can try to adapt available UNIX or Linux tests (like LTP).
> Hi Oleg,
>
> Thanks for your quick response and appreciated.
>
> As per your reply previous email message i.e "You can try adapt some open
> source project for your needs" , Please can you suggest couple of open source
> projects which can test QNX ?Oleg Bolshakov2019-10-16T12:24:51Zpost120050: Re: Test suite to validate QNX
http://community.qnx.com/sf/go/post120050
Hi Oleg,
Thanks for your quick response and appreciated.
As per your reply previous email message i.e "You can try adapt some open source project for your needs" , Please can you suggest couple of open source projects which can test QNX ?Koteswararao Nayudu(deleted)2019-10-16T12:10:33Zpost120049: Re: Test suite to validate QNX
http://community.qnx.com/sf/go/post120049
Hello Koteswararao,
Unfortunately, I didn't hear about ready to use publicly available test suite for QNX kernel. You can try adapt some open source project for your needs. Also note that some subsystems are not kernel parts in QNX (such filesystem or network).
Respectfully,
Oleg
> Hi,
>
> I am looking for the Test suite to validate QNX kernel like we have "LTP"
> (https://github.com/linux-test-project/ltp) for Linux kernel.
>
> Please can some one provide your suggestion to get the right test suite to
> validate QNX?
>
> Regards,
> KotiOleg Bolshakov2019-10-16T12:05:47Zpost120047: Test suite to validate QNX
http://community.qnx.com/sf/go/post120047
Hi,
I am looking for the Test suite to validate QNX kernel like we have "LTP" (https://github.com/linux-test-project/ltp) for Linux kernel.
Please can some one provide your suggestion to get the right test suite to validate QNX?
Regards,
KotiKoteswararao Nayudu(deleted)2019-10-16T09:59:00Zpost119697: HMI pointer glitch issue in qnx on imx6 sabresmart board
http://community.qnx.com/sf/go/post119697
I have been developing a embedded project in which a HMI is running on QNX OS on imx6dl sabre-smart board .HMI consist of a pointer pivoted at the middle traversing from right side to left side,just like a magnetic compass.I am using sdp6.6 for the building the IFS.HMI is using GPU for rendering.
The issue faced is pointer continuously flickers when moving from right to left or left to right. I have checked the graphics.conf file. It seems to be correctly configured.I have tried some solution to related to Multi frame-buffer similar to "export FB_MULTI_BUFFER" in case of Linux, but it did not work.
Can anyone provide me any solution or suggestion related to the issue?Sanjay Suthar(deleted)2019-05-07T08:08:51Zpost119075: Re: cp command cause root directory is gone (/ point is unmounted)
http://community.qnx.com/sf/go/post119075
Hi,
Thanks for replying.
the filesystem is QNX 4.Chris Liang(deleted)2018-09-05T21:15:21Zpost119074: Re: cp command cause root directory is gone (/ point is unmounted)
http://community.qnx.com/sf/go/post119074
Hi Chris,
This is QNX 4 discussion board, but your question about QNX 6 (next version). Please repeat your question in right forum.
Respectfully,
Oleg
5 сент. 2018 г., в 19:05, Chris Liang <community-noreply@qnx.com> написал:
> Hi,
>
> I encounter a problem that using cp command to copy a large file (~1GB size) from USB to SD card or vise versa. during copying, error out and root directory is gone (/ mount point is umounted).
>
> The following is verbose from cp:
> cp: LSTAT(/dos/d/,buf)
> cp: LSTAT(/log/file.121,buf)
> cp: copy_guy(/log/file.121,/dos/d///file.121)
> cp: OPEN(/log/file.121,0,0)
> cp: OPEN(/dos/d///file.121,2401,100640)
> cp: LSTAT(/dos/d///file.121,buf)
> cp: Copying /log/file.121 to /dos/d/file.121
> cp: write (/dos/d///file.121): Input/output error
> cp: ERRS++ (1) write()
> 88.74% (755840/851673 kbytes, 2323 kb/s)
> cp: read (/log/file.121): Bad file descriptor
> cp: ERRS++ (2) read()
> cp: past_data_copy errs_in =0, errs = 2
> cp: exit_copy_guy (rc=0)
> cp: CLOSE(fildes)
> cp: close (/log/file.121): Bad file descriptor
> cp: ERRS++ (3) _close()
> cp: CLOSE(fildes)
> cp: close (/dos/d///file.121): Bad file descriptor
> cp: ERRS++ (4) _close()
>
> QNX version: 6.4.1
> both SD card and usb key is running on USB bus. I can see during copy devb-umass and io-usb processes are taking CPU usages
>
> what could be the root cause of this?
>
> Thanks in advance.
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post119073
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2018-09-05T20:21:47Zpost119073: cp command cause root directory is gone (/ point is unmounted)
http://community.qnx.com/sf/go/post119073
Hi,
I encounter a problem that using cp command to copy a large file (~1GB size) from USB to SD card or vise versa. during copying, error out and root directory is gone (/ mount point is umounted).
The following is verbose from cp:
cp: LSTAT(/dos/d/,buf)
cp: LSTAT(/log/file.121,buf)
cp: copy_guy(/log/file.121,/dos/d///file.121)
cp: OPEN(/log/file.121,0,0)
cp: OPEN(/dos/d///file.121,2401,100640)
cp: LSTAT(/dos/d///file.121,buf)
cp: Copying /log/file.121 to /dos/d/file.121
cp: write (/dos/d///file.121): Input/output error
cp: ERRS++ (1) write()
88.74% (755840/851673 kbytes, 2323 kb/s)
cp: read (/log/file.121): Bad file descriptor
cp: ERRS++ (2) read()
cp: past_data_copy errs_in =0, errs = 2
cp: exit_copy_guy (rc=0)
cp: CLOSE(fildes)
cp: close (/log/file.121): Bad file descriptor
cp: ERRS++ (3) _close()
cp: CLOSE(fildes)
cp: close (/dos/d///file.121): Bad file descriptor
cp: ERRS++ (4) _close()
QNX version: 6.4.1
both SD card and usb key is running on USB bus. I can see during copy devb-umass and io-usb processes are taking CPU usages
what could be the root cause of this?
Thanks in advance.Chris Liang(deleted)2018-09-05T16:05:03Zpost119045: Re: What printer does QNX4.25 support ?
http://community.qnx.com/sf/go/post119045
Hi Cong,
You can try to use printers which supports raw text printing and/or PostScript.
Respectfully,
Oleg
9 авг. 2018 г., в 5:31:20, Cong Pham <community-noreply@qnx.com> написал:
> Hi,
>
> My project runs on QNX 4.25. It needs to print out some results in text format.
> Does QNX 4.25 support laser-jet and usb 2.0 printer ?
> My computer has COM, LPT and USB 2.0 ports.
>
> So what printer should I choose? Do you have any suggestions?
>
> ^_^
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post119044
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2018-08-09T10:24:03Zpost119044: What printer does QNX4.25 support ?
http://community.qnx.com/sf/go/post119044
Hi,
My project runs on QNX 4.25. It needs to print out some results in text format.
Does QNX 4.25 support laser-jet and usb 2.0 printer ?
My computer has COM, LPT and USB 2.0 ports.
So what printer should I choose? Do you have any suggestions?
^_^Cong Pham(deleted)2018-08-09T02:31:19Zpost118947: Re: PhAB: need help on exclusive toggle pushing button
http://community.qnx.com/sf/go/post118947
Hi,
Thank Mr Oleg Bolshakov and Mr Alexander Koppel for suggesting me.
I have used PtGroup and it worked fine.Cong Pham(deleted)2018-07-12T05:25:32Zpost118946: Re: PhAB: need help on exclusive toggle pushing button
http://community.qnx.com/sf/go/post118946
Alternatively, you can try placing toggle buttons in a group (PtGroup) with Pt_GROUP_EXCLUSIVE setAlexander Koppel2018-07-11T18:14:33Zpost118945: Re: PhAB: need help on exclusive toggle pushing button
http://community.qnx.com/sf/go/post118945
Hi Cong,
You can use something like the following callback function for all three buttons:
---
int
ButtonSet( PtWidget_t *widget, ApInfo_t *apinfo, PtCallbackInfo_t *cbinfo )
{
PtArg_t arg[1];
/* eliminate 'unreferenced' warnings */
widget = widget, apinfo = apinfo, cbinfo = cbinfo;
if( widget == ABW_PtButton1 ){
PtSetArg( &arg[0], Pt_ARG_FLAGS, Pt_TRUE, Pt_SET );
PtSetResources( ABW_PtButton1, 1, &arg[0] );
PtSetArg( &arg[0], Pt_ARG_FLAGS, Pt_FALSE, Pt_SET );
PtSetResources( ABW_PtButton2, 1, &arg[0] );
PtSetArg( &arg[0], Pt_ARG_FLAGS, Pt_FALSE, Pt_SET );
PtSetResources( ABW_PtButton3, 1, &arg[0] );
} else if ( widget == ABW_PtButton2 ){
PtSetArg( &arg[0], Pt_ARG_FLAGS, Pt_FALSE, Pt_SET );
PtSetResources( ABW_PtButton1, 1, &arg[0] );
PtSetArg( &arg[0], Pt_ARG_FLAGS, Pt_TRUE, Pt_SET );
PtSetResources( ABW_PtButton2, 1, &arg[0] );
PtSetArg( &arg[0], Pt_ARG_FLAGS, Pt_FALSE, Pt_SET );
PtSetResources( ABW_PtButton3, 1, &arg[0] );
} else if ( widget == ABW_PtButton3 ){
PtSetArg( &arg[0], Pt_ARG_FLAGS, Pt_FALSE, Pt_SET );
PtSetResources( ABW_PtButton1, 1, &arg[0] );
PtSetArg( &arg[0], Pt_ARG_FLAGS, Pt_FALSE, Pt_SET );
PtSetResources( ABW_PtButton2, 1, &arg[0] );
PtSetArg( &arg[0], Pt_ARG_FLAGS, Pt_TRUE, Pt_SET );
PtSetResources( ABW_PtButton3, 1, &arg[0] );
}
return( Pt_CONTINUE );
}
---
Pt_TOGGLE should be set for all three buttons.
Respectfully,
Oleg
11 июля 2018 г., в 12:59, Cong Pham <community-noreply@qnx.com> написал:
> Hi,
>
> I have a Photon application with three exclusive chosen options.
> My window need three push buttons to select each option.
> When user push a button, it must be "set" and all other are "unset". If one of them is set before, it must be unset.
>
> How can I do ? I have set Pt_TOGGLE bit but it just "set" itseft and do not "unset" all other ones.
>
>
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post118937
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
> <toggle_button.png>Oleg Bolshakov2018-07-11T18:07:22Zpost118937: PhAB: need help on exclusive toggle pushing button
http://community.qnx.com/sf/go/post118937
Hi,
I have a Photon application with three exclusive chosen options.
My window need three push buttons to select each option.
When user push a button, it must be "set" and all other are "unset". If one of them is set before, it must be unset.
How can I do ? I have set Pt_TOGGLE bit but it just "set" itseft and do not "unset" all other ones.Cong Pham(deleted)2018-07-11T09:59:45Zpost118869: Re: Watchdog software support in QNX
http://community.qnx.com/sf/go/post118869
Hi Ananda,
QNX 4 doesn't share any generic watchdog API. You can use API that provided by your watchdog driver or you can develop driver for your watchdog controller with your own API.
Respectfully,
Oleg
6 июня 2018 г., в 10:12:08, Ananda Kavrady <community-noreply@qnx.com> написал:
> Hi
>
> I am currently working on Linux and QNX operating system variants.
>
> In linux I am using systemd for watchdog support as below API provides.
>
> sd_watchdog_enabled(0, &_watchdogTimeoutInverval);
>
> Sd_Notify() is used to send the heartbeats.
>
> How can get watchdog support in QNX? . Is there any alternative approach
>
>
> ~Regards
> Ananda kOleg Bolshakov2018-06-06T09:49:23Zpost118868: Watchdog software support in QNX
http://community.qnx.com/sf/go/post118868
Hi
I am currently working on Linux and QNX operating system variants.
In linux I am using systemd for watchdog support as below API provides.
sd_watchdog_enabled(0, &_watchdogTimeoutInverval);
Sd_Notify() is used to send the heartbeats.
How can get watchdog support in QNX? . Is there any alternative approach
~Regards
Ananda kAnanda Kavrady(deleted)2018-06-06T07:30:21Zpost118858: Re: QNX6.6 blank screen issue with WFD Driver on Freescale i.MX6Q Sabre Board for Smart Devices
http://community.qnx.com/sf/go/post118858
Hi Ankit,
If you require immediate support, please file a support case. If you cannot access the support portal here:
https://www.qnx.com/account/tslogin.html
Please contact your sales rep.
Cheers,
KevinKevin Kunka2018-05-30T14:10:22Zpost118857: QNX6.6 blank screen issue with WFD Driver on Freescale i.MX6Q Sabre Board for Smart Devices
http://community.qnx.com/sf/go/post118857
Hello,
For one of our embedded system we have a issue with blank screen while using WFD Driver.
Please find attached document for detail.
Can we have quick support/discussion/resolution/workaround for this ?
We need urgent support for this.
-Ankit.t yh(deleted)2018-05-30T09:08:13Zpost118767: Re: RE: Can´t install QNX4...
http://community.qnx.com/sf/go/post118767
I had the same problem with a laptop. I found that if I disable SATA Native support in the BIOS it found it and loaded the OS without any other problems.
Hope this helpsHarry Qualls(deleted)2018-04-12T19:04:01Zpost118674: Re: QNX4 Product Suite June 2008
http://community.qnx.com/sf/go/post118674
No it doesn't need to be patched twiceresa roid(deleted)2018-03-15T20:12:29Zpost118666: RE: Can´t install QNX4...
http://community.qnx.com/sf/go/post118666
Thanks for your answer Oleg. I Will try as you said.
Thanks....
-----Mensaje original-----
De: Олег Большаков <community-noreply@qnx.com>
Enviado el: lunes, 12 de marzo de 2018 01:56 a. m.
Para: qnx4-community@community.qnx.com
Asunto: Re: Can´t install QNX4...
Hello Victor,
Currently QNX 4 Install CD update is not planning for this year. Though you can remove a HDD, install QNX 4 to the HDD on another PC and install the HDD again to the server.
Respectfully,
Oleg
8 марта 2018 г., в 22:44:41, Victor Gamboa <community-noreply@qnx.com> написал:
> One server with QNX4 is failing, so I need to install QNX4 in a new one to reeplace the bad one. I have tried to install QNX 4 using the QNX4 Product Suite 2015, but the auto-detecting hardware don't recognize the EIDE Disk Controller neither the ACHI Disk Controller, so I can´t install the OS. Does anyone have update or install QNX4 this year ? I really appreciate any help. Thanks. Víctor Gamboa.
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post118658
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
_______________________________________________
QNX4 Community Support
http://community.qnx.com/sf/go/post118662
To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comVictor Gamboa2018-03-14T01:12:45Zpost118662: Re: Can´t install QNX4...
http://community.qnx.com/sf/go/post118662
Hello Victor,
Currently QNX 4 Install CD update is not planning for this year. Though you can remove a HDD, install QNX 4 to the HDD on another PC and install the HDD again to the server.
Respectfully,
Oleg
8 марта 2018 г., в 22:44:41, Victor Gamboa <community-noreply@qnx.com> написал:
> One server with QNX4 is failing, so I need to install QNX4 in a new one to reeplace the bad one. I have tried to install QNX 4 using the QNX4 Product Suite 2015, but the auto-detecting hardware don't recognize the EIDE Disk Controller neither the ACHI Disk Controller, so I can´t install the OS. Does anyone have update or install QNX4 this year ? I really appreciate any help. Thanks. Víctor Gamboa.
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post118658
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2018-03-12T08:16:51Zpost118658: Can´t install QNX4...
http://community.qnx.com/sf/go/post118658
One server with QNX4 is failing, so I need to install QNX4 in a new one to reeplace the bad one. I have tried to install QNX 4 using the QNX4 Product Suite 2015, but the auto-detecting hardware don't recognize the EIDE Disk Controller neither the ACHI Disk Controller, so I can´t install the OS. Does anyone have update or install QNX4 this year ? I really appreciate any help. Thanks. Víctor Gamboa.Victor Gamboa2018-03-08T19:44:41Zpost118654: Re: Problems installing QNX4 in a new computer....
http://community.qnx.com/sf/go/post118654
This may be a little late but I had a similar problem a few years ago with new Dell Computers. I ended up changing the initial boot loader to the old original used by the install CD's. The command to change it is;
dinit -h -b -O /dev/hd0.0t77.
The -h is for fixed disk not removeable device
The -b is for the bootloader
The -O is for the old bootloader.
Hope this helps you in the future.
BradHarry Qualls(deleted)2018-03-05T16:40:01Zpost118636: Re: AMD T16R Graphic Driver Problem
http://community.qnx.com/sf/go/post118636
Hi Oleg,
Thank you for your professional guidance, everything is running well. I really appreciate for your help!
Best Regards
Sincerely
JackJack Zhang2018-02-28T17:07:33Zpost118635: Re: AMD T16R Graphic Driver Problem
http://community.qnx.com/sf/go/post118635
You do not need to use USB if keyboard works in text mode. It seems that you use the USB legacy mode on. Do not add Input to input.<NODE> file, change it to:
kbd -R fd -d/dev/kbd
Respectfully,
Oleg
28 февр. 2018 г., в 16:03:11, Jack Zhang <community-noreply@qnx.com> написал:
> Hi Oleg,
>
> The Input.node file is attached. And when I run 'io-usb -d ohci pindex=1', nothing is done, and there is no usbkbd0 file under /dev.
>
>
> Sincerely
>
> Jack
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post118633
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
> <Input.5>Oleg Bolshakov2018-02-28T13:10:10Zpost118634: Re: AMD T16R Graphic Driver Problem
http://community.qnx.com/sf/go/post118634
I guess the problem may be in:
> I connect one usb keyboard to this motherboard only!
If you don't have the mouse you have to change default input.<NODE> file. It seems that you have forgotten to attach yours. But if this is your issue you have to remove mouse from config. Change:
kbd fd -d/dev/kbd ps2 -r kb -2
to:
kbd fd -d/dev/kbd
Respectfully,
Oleg
28 февр. 2018 г., в 13:55:01, Jack Zhang <community-noreply@qnx.com> написал:
> Hi Oleg,
>
> First of all, thank you for your help. You are right, in fact it is the input driver problem. The system stuck at loading the input driver, due to wrong input driver. Then I told the RD to change the bios to emulate USB keyboard.
>
> Do you have any advice about how to use usb keyboard in Photon?
>
> I note that it is ok to use usb keyboard in shell, but now it is not work in photon, is there any steps that I have forgotten?
>
> I connect one usb keyboard to this motherboard only!
>
> Sincerely
>
> Jack
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post118632
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2018-02-28T13:05:33Zpost118633: Re: AMD T16R Graphic Driver Problem
http://community.qnx.com/sf/go/post118633
Hi Oleg,
The Input.node file is attached. And when I run 'io-usb -d ohci pindex=1', nothing is done, and there is no usbkbd0 file under /dev.
Sincerely
JackJack Zhang2018-02-28T13:03:11Zpost118632: Re: AMD T16R Graphic Driver Problem
http://community.qnx.com/sf/go/post118632
Hi Oleg,
First of all, thank you for your help. You are right, in fact it is the input driver problem. The system stuck at loading the input driver, due to wrong input driver. Then I told the RD to change the bios to emulate USB keyboard.
Do you have any advice about how to use usb keyboard in Photon?
I note that it is ok to use usb keyboard in shell, but now it is not work in photon, is there any steps that I have forgotten?
I connect one usb keyboard to this motherboard only!
Sincerely
JackJack Zhang2018-02-28T10:55:01Zpost118631: Re: AMD T16R Graphic Driver Problem
http://community.qnx.com/sf/go/post118631
Hi Jack,
I see that you don't have graphics driver problem, but input drivers problem. Graphics seems to work fine.
Can you attach your input.<NODE> file? Which input devices do you use (keyboard, mouse)?
Respectfully,
Oleg
27 февр. 2018 г., в 18:19:38, Jack Zhang <community-noreply@qnx.com> написал:
> Hi Oleg,
>
> There is no remote access to this device, I can descript it. I reinstall the OS again, and I choose to probe the video, but it can't be applied with the selected resolution config, then I press the F3 to exit. You know at this time, the crt.5 had been created, then I copy the 1028x768x8 line to the first line. Last, I change the OS boot into text mode(picture 01), input the ph, then it boots into the Photon same as the picture 02. But you can see it, it is abnormal, it is freezed, and I can't use the USB keyboard.
>
> If i don't change it to text mode, it will stuck at Waiting for input driver..., same as the picture 03.
>
>
> Sincerely
>
> Jack
>
>
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post118629
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
> <03.jpg><01.jpg><02.jpg><sysinit.5>Oleg Bolshakov2018-02-28T08:48:06Zpost118629: Re: AMD T16R Graphic Driver Problem
http://community.qnx.com/sf/go/post118629
Hi Oleg,
There is no remote access to this device, I can descript it. I reinstall the OS again, and I choose to probe the video, but it can't be applied with the selected resolution config, then I press the F3 to exit. You know at this time, the crt.5 had been created, then I copy the 1028x768x8 line to the first line. Last, I change the OS boot into text mode(picture 01), input the ph, then it boots into the Photon same as the picture 02. But you can see it, it is abnormal, it is freezed, and I can't use the USB keyboard.
If i don't change it to text mode, it will stuck at Waiting for input driver..., same as the picture 03.
Sincerely
JackJack Zhang2018-02-27T15:19:38Zpost118628: Re: AMD T16R Graphic Driver Problem
http://community.qnx.com/sf/go/post118628
Can you describe in detail what you see after launching ph command?
Do you have remote access (telnet or ditto) to this system? Try to start ph remotely and attach here the output if any.
Respectfully,
Oleg
27 февр. 2018 г., в 15:30:39, Jack Zhang <community-noreply@qnx.com> написал:
> Hi Oleg,
>
> I really appreciate your help, I have attached the show_pci output file, please help me to check it.
>
> Besides, I have tried every different display resolution line in the crt.5, it seems still not work. And I reboot the motherboard after executing of crttrap before launching ph.
>
> Sincerely
>
> Jack
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post118627
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
> <show_pci>Oleg Bolshakov2018-02-27T13:35:09Zpost118627: Re: AMD T16R Graphic Driver Problem
http://community.qnx.com/sf/go/post118627
Hi Oleg,
I really appreciate your help, I have attached the show_pci output file, please help me to check it.
Besides, I have tried every different display resolution line in the crt.5, it seems still not work. And I reboot the motherboard after executing of crttrap before launching ph.
Sincerely
JackJack Zhang2018-02-27T12:30:39Zpost118626: Re: AMD T16R Graphic Driver Problem
http://community.qnx.com/sf/go/post118626
Hi Jack,
Can you attach here the show_pci -vvv from PCM-3356? Didn't you forget to copy appropriate Hydra.ms/Pg.flat lines to the first line in your crt.<NODE> file? Did you reboot after executing of crttrap before launching ph? Try to use lines with Pg.flatdc32 and standard graphics modes (like 1280x1024x32 and so on). Also you can try to add additional keys -r or -e to Hydra.ms options.
Respectfully,
Oleg
26 февр. 2018 г., в 20:17:03, Jack Zhang <community-noreply@qnx.com> написал:
> I have already used crttrap trap in the text mode to detect the graphic driver and I have attached the crt file. I have tried the Hydra.ms/Pg.flat drivers but none of them is working.
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post118624
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
> <crt.5>Oleg Bolshakov2018-02-27T10:29:27Zpost118624: Re: AMD T16R Graphic Driver Problem
http://community.qnx.com/sf/go/post118624
I have already used crttrap trap in the text mode to detect the graphic driver and I have attached the crt file. I have tried the Hydra.ms/Pg.flat drivers but none of them is working.Jack Zhang2018-02-26T17:17:03Zpost118623: AMD T16R Graphic Driver Problem
http://community.qnx.com/sf/go/post118623
Hi Oleg,
I'm trying to install the latest experimental Install CD to the Advantech motherboard PCM-3356(cpu:AMD T16R). But I can't make it. It can not boot into Photon, due to there is no corresponding graphic driver. Will you please help me with this, I really appreciate any help from you, Thank you!
JackJack Zhang2018-02-26T16:44:41Zpost118370: Re: is there pcie server driver which suite for i.mx6q sabrlite?》
http://community.qnx.com/sf/go/post118370
Hello Philip,
This is QNX 4 discussion board. QNX 4 doesn't support ARM CPUs. Please ask your question in QNX 6 discussion board.
Respectfully,
Oleg
12 янв. 2018 г., в 16:39:56, philip wang(deleted) <community-noreply@qnx.com> написал:
> I have download bsp about i.mx6q, but there is no pcie server driver code.
> is there pcie server driver which suite for i.mx6q sabrlite?
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post118369
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2018-01-12T13:43:52Zpost118369: is there pcie server driver which suite for i.mx6q sabrlite?》
http://community.qnx.com/sf/go/post118369
I have download bsp about i.mx6q, but there is no pcie server driver code.
is there pcie server driver which suite for i.mx6q sabrlite?philip wang(deleted)2018-01-12T13:39:56Zpost118098: Re: QNX4 support for Intel i210 and i211 ethernet?
http://community.qnx.com/sf/go/post118098
Oleg:
An Update. I found that the 2015 Experimental driver didn't work. I had the same problem as described in post114602.
However the 27-4-2016 net.e1000 driver works just fine.
Thanks for the update,
AndyAndy Rhind2017-10-11T04:51:35Zpost118015: Re: QNX4 support for Intel i210 and i211 ethernet?
http://community.qnx.com/sf/go/post118015
Oleg:
Thank you for the reply. I'll try the board out and let you know the results.
AndyAndy Rhind2017-09-05T23:48:50Zpost118011: Re: QNX4 support for Intel i210 and i211 ethernet?
http://community.qnx.com/sf/go/post118011
Hi Andy,
Intel i210 and i211 are both supported by Net.e1000 from the following web-page:
http://community.qnx.com/sf/wiki/do/viewPage/projects.qnx4/wiki/LatestSoftwareUpdates
But it's better to test hardware before purchasing if possible.
Respectfully,
Oleg
4 сент. 2017 г., в 16:05:13, Andy Rhind <community-noreply@qnx.com> написал:
> Hi:
>
> Can you let me know the status of support for the Intel i210 and i211 Ethernet chipsets?
>
> Thanks,
> Andty
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post118010
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2017-09-04T14:12:31Zpost118010: QNX4 support for Intel i210 and i211 ethernet?
http://community.qnx.com/sf/go/post118010
Hi:
Can you let me know the status of support for the Intel i210 and i211 Ethernet chipsets?
Thanks,
AndtyAndy Rhind2017-09-04T13:05:13Zpost117925: Request QNX to focus Baladesh, we also have voice just need practical work support!!!
http://community.qnx.com/sf/go/post117925
Now its been greatly discussed in all global intellectual and creative forums whether Higher Education at all necessary!! Wide coverage of mobile phone networks, fast internet facility and mass connectivity of social networks put all the traditional concepts indulge. Being innovative with creative idea(s) and knowing smart uses of cellphone device matters most to have your access in governance. It has been already recognised by the UN that every individual has the credibility now to be accountable with his or her contribution for global impact.
Our recent game changing experience in 3rd world countries speaks all about the karma of Social Networking and end user Mobile Phone connectivity. Even recent US election also an example of fact. It doesn't matter any more to be smart or skilled for any individual through higher degree or software/hardware/programme knowledge, rather living in the reign of G net your adaptability with Information Society matters most. Your basic knowledge of IT is enough to transform the information society digitally. Mobile phone banking facilities now as strong as debit/credit card, with a social media pages or groups you now can meet most of your demand of a server/domain and with a social network id free using of IMs you can manage your meet ups!! This is all about ICT!!!
In many ways ICT can be intercepted based on the requirements of a certain community or locales. All the global stack holders and all UN countries have endorsed the global implementation strategy of ICTS. The basic fundamental of ICTS are generalised with commons :-
1) A2i 2) Freedom of Expression 3) Equality 4) Self Determine Rights of Individually 5) Go Green
Hence in line with said values ICTS frameworks adopted by WTO, ITU, WB, IMF and other global/regional Trade, Finance & Commerce authorities for their members to prioritise their investment in human resources with allout acts :- 1) Digitalisation of Information Society 2) Local Youth Partnership 3) Support Service Provider promotion 4) Innovative Entrepreneur Funding 5) e Banking 6) e Commerce 7) Food Safety 8) Security 9) Communication & Infrastructure Development 10) Health Sector Funding 11) Good Governance Project funding 12) Education & Capacity Building 13) Urbanisation and many more!!
Apart from above global SOP, based on the demographic the NGO's, Govt, Development Partners, Corporates and other local organisations related to the governance were bound with UN declaration to invest, monitor and maintain their course for Fight Against Hunger & Poverty. The mendetory works for ICTS to be integrated locally as under :-
1) Facilities of digital class and online schooling to ensure education for all.
2) e-Learning and vocational training for skilled human resources
3) SME funding to the local digital service providers.
4) Promotional media & door to door activities to grow health awareness and safety to the mother & child.
5) Governance and community development related Innovative Entrepreneur funding to encourage leadership and partnership access to the local governance.
6) Promote social awareness and grow consensus of citizens to strengthen the social moral values.
7) Community support services by Help Desk to facilitate the society with all necessary resources as needed.
8) Encourage free lab or community hall to facilitate youngs to share their creative ideas and seniors to meet the society.
9) Promote legal aid service by the locals to protect women and children rights.
10) Promote citizen charter to enable local youths to be paid in engage with vigilant activities to protect consumers rights.
Therefore, here lies great opportunity for BlackBerry/QNX to experience ICTS Offshore credibility empowered by social networking only. In the context of Bangladesh having nearly 11 billion mobile phone users and having highest rate of social media users in South East Asia, I invite forum members to feel free to contact me for more support on Offshore integration of ICT. Sure it would be an unique opportunity for the developers!! Zavedctg@live.comzaved solaiman(deleted)2017-07-31T05:07:50Zpost117757: Re: Killing tasks...
http://community.qnx.com/sf/go/post117757
Hi Victor,
Great! It’s nice to know about this.
Respectfully,
Oleg
23 мая 2017 г., в 1:04, Victor Gamboa <community-noreply@qnx.com> написал:
> Thanks Oleg. I did the script and it works.
> Best Regards,
> Victor.
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post117755
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2017-05-23T04:56:30Zpost117755: Re: Killing tasks...
http://community.qnx.com/sf/go/post117755
Thanks Oleg. I did the script and it works.
Best Regards,
Victor.Victor Gamboa2017-05-22T22:04:33Zpost117747: Re: Killing tasks...
http://community.qnx.com/sf/go/post117747
Hi Victor,
You can find awk overview and some samples in QNX 4 Help:
Contents / QNX 4.25 / Utilities Reference / A / awk
Also there are a lot of examples in the Internet. You can start from here:
https://en.wikipedia.org/wiki/AWK
Respectfully,
Oleg
19 мая 2017 г., в 2:21:24, Victor Gamboa <community-noreply@qnx.com> написал:
> Do you have any awk script example to guide me ?
> Thanks in advance for your help.
>
> Víctor.
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post117746
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2017-05-19T07:47:44Zpost117746: Re: Killing tasks...
http://community.qnx.com/sf/go/post117746
Do you have any awk script example to guide me ?
Thanks in advance for your help.
Víctor.Victor Gamboa2017-05-18T23:21:24Zpost117744: Re: Killing tasks...
http://community.qnx.com/sf/go/post117744
Thanks Oleg, I will try with awk.Victor Gamboa2017-05-18T15:00:03Zpost117743: Re: Killing tasks...
http://community.qnx.com/sf/go/post117743
Hi Victor,
There is no special utility that kills tasks which inactive for some time. Try to use awk to parse who utility output.
Respectfully,
Oleg
17 мая 2017 г., в 22:25:33, Victor Gamboa <community-noreply@qnx.com> написал:
> Is there any way to automate the killing of tasks wich has more then 30 minutos idle, for example, on QNX 4 ?
> I think that I can make an script that execute with cron, but I don´t know if there are any commands to do this.
> I really appreciate any help.
> Victor.
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post117739
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2017-05-18T12:00:53Zpost117739: Killing tasks...
http://community.qnx.com/sf/go/post117739
Is there any way to automate the killing of tasks wich has more then 30 minutos idle, for example, on QNX 4 ?
I think that I can make an script that execute with cron, but I don´t know if there are any commands to do this.
I really appreciate any help.
Victor.Victor Gamboa2017-05-17T19:25:33Zpost117711: Re: QNX 6.5.0 support for both LE and BE on ARM926EJ-S
http://community.qnx.com/sf/go/post117711
Hi Heston,
This is QNX 4 discussion board, the previous version of QNX Neutrino. Please ask your question in QNX 6 board.
Respectfully,
Oleg
4 мая 2017 г., в 20:14, Heston Holtmann <community-noreply@qnx.com> написал:
> We are using QNX 6.5.0 on a TI OMAP-L138 ARM926EJ-S based processor (SoC)
> We are running the system in Little-Endian (LE) Mode... simply because that was the default build of QNX supporting that chip that was provided in the Momentics build system.
> ..
> But I am wondering.. in hind-sight.. was there also a Big Endian (BE) native build of QNX 6.5.0 for the ARM926EJ-S
> Did we have a choice all along to stick with Big Endian to minimizing porting complexity from our QNX Application and protocol code that came from PowerPC (Big Endian).
>
> Heston
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post117710
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2017-05-04T18:03:50Zpost117710: QNX 6.5.0 support for both LE and BE on ARM926EJ-S
http://community.qnx.com/sf/go/post117710
We are using QNX 6.5.0 on a TI OMAP-L138 ARM926EJ-S based processor (SoC)
We are running the system in Little-Endian (LE) Mode... simply because that was the default build of QNX supporting that chip that was provided in the Momentics build system.
..
But I am wondering.. in hind-sight.. was there also a Big Endian (BE) native build of QNX 6.5.0 for the ARM926EJ-S
Did we have a choice all along to stick with Big Endian to minimizing porting complexity from our QNX Application and protocol code that came from PowerPC (Big Endian).
HestonHeston Holtmann(deleted)2017-05-04T17:14:18Zpost117671: Re: Problems installing QNX4 in a new computer....
http://community.qnx.com/sf/go/post117671
Thanks anyway Oleg. I solved the situation installing an old motherbard, but I hope that QNX4 works on the new chipset soon. Thanks...Victor Gamboa2017-04-24T16:25:15Zpost117670: Re: Problems installing QNX4 in a new computer....
http://community.qnx.com/sf/go/post117670
Hi Victor,
Unfortunately, I don't have H110 motherboard to check this.
Respectfully,
Oleg
21 апр. 2017 г., в 17:55:53, Victor Gamboa <community-noreply@qnx.com> написал:
> The hardware scan on the installation found an AHCI adapter, but none device.
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post117666
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2017-04-24T14:35:08Zpost117666: Re: Problems installing QNX4 in a new computer....
http://community.qnx.com/sf/go/post117666
The hardware scan on the installation found an AHCI adapter, but none device.Victor Gamboa2017-04-21T14:55:53Zpost117665: Re: Problems installing QNX4 in a new computer....
http://community.qnx.com/sf/go/post117665
Hi Oleg, thank you for your answer.
I tried with the experimental cd that you mentioned but unfortunatly it didn't recognize any AHCI device, it did'nt recognize any hard drive. Is there any other possible solution ? I really appreciate your help.
Victor.Victor Gamboa2017-04-21T14:50:13Zpost117662: Re: Problems installing QNX4 in a new computer....
http://community.qnx.com/sf/go/post117662
Hi Victor,
Did you try to install QNX 4 from the latest experimental Install CD? This CD can install on AHCI systems:
http://community.qnx.com/sf/wiki/do/viewPage/projects.qnx4/wiki/LatestSoftwareUpdates
Read here how to enable AHCI support:
http://community.qnx.com/sf/wiki/do/viewPage/projects.qnx4/wiki/ProductSuite2015ExperimentalReleaseNotes
Respectfully,
Oleg
21 апр. 2017 г., в 1:24, Victor Gamboa <community-noreply@qnx.com> написал:
> Hi Sirs:
> I need to change the QNX4 server, so I tried with 3 different motherboars Asus, Gigabyte H110-DS2 and ECS B150M4-C43 wich use the intel H110 express chipset but QNX didn´t work. The Asus Bios doesn´t have any opcion to set the SATA to Legacy or AHCI, the other 2 has only AHCI. I tried insalling QNX on another machine, updating the Proc32, and changing the sys/boot to:
> /bin/Fsys.ahci
> $ /bin/Fsys.ahci fsys -Ndsk0 -n0=hd0. -n5=cd0.
> but the QNX didn´t boot. The boot process begins and said that doesn´t have any AHCI devices.
> I really appreciate any help I need to change the QNX4 server because the actual one is having problems. I thank you in advance for any help.
> Victor.
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post117660
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2017-04-21T06:50:16Zpost117660: Problems installing QNX4 in a new computer....
http://community.qnx.com/sf/go/post117660
Hi Sirs:
I need to change the QNX4 server, so I tried with 3 different motherboars Asus, Gigabyte H110-DS2 and ECS B150M4-C43 wich use the intel H110 express chipset but QNX didn´t work. The Asus Bios doesn´t have any opcion to set the SATA to Legacy or AHCI, the other 2 has only AHCI. I tried insalling QNX on another machine, updating the Proc32, and changing the sys/boot to:
/bin/Fsys.ahci
$ /bin/Fsys.ahci fsys -Ndsk0 -n0=hd0. -n5=cd0.
but the QNX didn´t boot. The boot process begins and said that doesn´t have any AHCI devices.
I really appreciate any help I need to change the QNX4 server because the actual one is having problems. I thank you in advance for any help.
Victor.Victor Gamboa2017-04-20T22:24:33Zpost117559: Re: QNX4 in USB
http://community.qnx.com/sf/go/post117559
Hi Cong,
There are no special Fsys drivers for MicroSD controller in QNX 4.
Respectfully,
Oleg
25 марта 2017 г., в 4:44:15, Cong Pham <community-noreply@qnx.com> написал:
> Oh no, I want to mount and boot my MicroSD card, it is plugged on board directly, not via SDcard reader.
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post117554
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2017-03-27T13:25:59Zpost117554: Re: QNX4 in USB
http://community.qnx.com/sf/go/post117554
Oh no, I want to mount and boot my MicroSD card, it is plugged on board directly, not via SDcard reader.Cong Pham(deleted)2017-03-25T01:44:15Zpost117553: Re: QNX4 in USB
http://community.qnx.com/sf/go/post117553
Hello Cong,
You can use Fsys.umass for MicroSD connected via USB-reader.
Respectfully,
Oleg
24 марта 2017 г., в 6:57, Cong Pham <community-noreply@qnx.com> написал:
> And,
>
> If I want to use MicroSD card, what Fsys driver can I use to mount?
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post117552
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2017-03-24T05:12:43Zpost117552: Re: QNX4 in USB
http://community.qnx.com/sf/go/post117552
And,
If I want to use MicroSD card, what Fsys driver can I use to mount?Cong Pham(deleted)2017-03-24T03:57:51Zpost117551: Re: QNX4 in USB
http://community.qnx.com/sf/go/post117551
Hi Mr Oleg,
I replaced io-usb by io-usb-ehci , as you said.
It boot ok, but slowly :)Cong Pham(deleted)2017-03-23T09:30:03Zpost117550: Re: QNX4 in USB
http://community.qnx.com/sf/go/post117550
Hi Cong,
I guess the image may be too large. Try to tune your build file first. Exclude Slib16. It is not needed at boot time, you can launch it later if required. Also replace io-usb to io-usb-ehci. Can you boot up with that new image?
Respectfully,
Oleg
23 марта 2017 г., в 7:32, Cong Pham <community-noreply@qnx.com> написал:
> Hi Everybody,
>
> I have to install QNX4 to a usb disk.
> 1. Format disk:
>
> # fdisk /dev/hd0 >>> make type t77, bootable
>
> # dinit /dev/hd0t77
>
> 2. Change .boot file:
> I created a boot script that:
>
> /boot/sys/boot
> $ /boot/sys/boot -v
>
> /boot/sys/Proc32
> $ /boot/sys/Proc32 -l 11
>
> /boot/sys/Slib32
> $ /boot/sys/Slib32
>
> /boot/sys/Slib16
> $ /boot/sys/Slib16
>
> /bin/io-usb
> $ /bin/io-usb &
>
> /bin/Fsys
> $ /bin/Fsys
>
> /bin/Fsys.umass
> $ /bin/Fsys.umass fsys -n0=hd0
>
> /bin/mount
> $ /bin/mount -p /dev/hd0 /dev/hd0t77 /
>
> /bin/sinit
> $ /bin/sinit TERM=qnxm
>
> Then I run buildqnx to make .boot file and copy it to root directory.
>
> But it hangs on "Start QNX.."
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post117549
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
> <IMG_1327[1].JPG>Oleg Bolshakov2017-03-23T06:02:19Zpost117549: QNX4 in USB
http://community.qnx.com/sf/go/post117549
Hi Everybody,
I have to install QNX4 to a usb disk.
1. Format disk:
# fdisk /dev/hd0 >>> make type t77, bootable
# dinit /dev/hd0t77
2. Change .boot file:
I created a boot script that:
/boot/sys/boot
$ /boot/sys/boot -v
/boot/sys/Proc32
$ /boot/sys/Proc32 -l 11
/boot/sys/Slib32
$ /boot/sys/Slib32
/boot/sys/Slib16
$ /boot/sys/Slib16
/bin/io-usb
$ /bin/io-usb &
/bin/Fsys
$ /bin/Fsys
/bin/Fsys.umass
$ /bin/Fsys.umass fsys -n0=hd0
/bin/mount
$ /bin/mount -p /dev/hd0 /dev/hd0t77 /
/bin/sinit
$ /bin/sinit TERM=qnxm
Then I run buildqnx to make .boot file and copy it to root directory.
But it hangs on "Start QNX.."Cong Pham(deleted)2017-03-23T04:32:22Zpost117535: Re: Killing processes
http://community.qnx.com/sf/go/post117535
Hi Victor,
I guess you can use awk or sed to check idle time.
Respectfully,
Oleg
14 марта 2017 г., в 5:39:12, Victor Gamboa <community-noreply@qnx.com> написал:
> When I used who, I got a list of user who are logged in like this:
> Userid Device Login Idle Command
> americas2 //1/dev/ttyp1 Mar 13 19:56 1:31:51 vpg4
> playa //1/dev/ttyp2 Mar 13 19:45 1:40:15 vpg4
> CALLE60 //1/dev/ttyp3 Mar 13 19:56 1:33:41 vpg4
>
> and I can kill the process with long idle time like this:
>
> slay -t /dev/ttyp1 vpg4
>
> How can I kiil all processes with 1 hour idle time for example ?
>
> I thank you in advance for any help on this.
>
> Victor
>
>
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post117533
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2017-03-14T13:54:39Zpost117534: Re: Killing processes
http://community.qnx.com/sf/go/post117534
If I could configure the telnet sessions to keep alive, I solve the situation, so another aproach could be telnet configuration to maintain alive the sessions. Any ideas ?
Thanks for the help.
Victor.Victor Gamboa2017-03-14T04:23:42Zpost117533: Killing processes
http://community.qnx.com/sf/go/post117533
When I used who, I got a list of user who are logged in like this:
Userid Device Login Idle Command
americas2 //1/dev/ttyp1 Mar 13 19:56 1:31:51 vpg4
playa //1/dev/ttyp2 Mar 13 19:45 1:40:15 vpg4
CALLE60 //1/dev/ttyp3 Mar 13 19:56 1:33:41 vpg4
and I can kill the process with long idle time like this:
slay -t /dev/ttyp1 vpg4
How can I kiil all processes with 1 hour idle time for example ?
I thank you in advance for any help on this.
VictorVictor Gamboa2017-03-14T02:39:12Zpost117262: Re: neutrino 6.6
http://community.qnx.com/sf/go/post117262
Hello!
This is discussion board for QNX 4 RTOS the predecessor of QNX 6. Please ask your question in suitable discussion board.
Respectfully,
Oleg
8 дек. 2016 г., в 5:45:00, ant17 ant17 <community-noreply@qnx.com> написал:
> hi i have just booted qnx neutrino 6.6 from a sd card in my beaglebone black after loading the drivers it stops at prompt is it supposed to boot into a gui
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post117261
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2016-12-08T11:07:06Zpost117261: neutrino 6.6
http://community.qnx.com/sf/go/post117261
hi i have just booted qnx neutrino 6.6 from a sd card in my beaglebone black after loading the drivers it stops at prompt is it supposed to boot into a guiant17 ant17(deleted)2016-12-08T02:45:00Zpost117065: Re: system load problem caused by socket
http://community.qnx.com/sf/go/post117065
Hi Oleg,
thanks for your reply. I took the state of all machine. If problem occurs again i will write a mail here. Hope it does not occur again, We have no idea what happen, because systems were runing over years without problems und run now since 4 weeks without problems too.
Greatings HansHans Lehmann(deleted)2016-11-03T13:38:24Zpost117036: Re: system load problem caused by socket
http://community.qnx.com/sf/go/post117036
Hi Hans,
I’ve never heard about this problem before. Please note that some processes may set they priority to serve clients requests. Also note that supported version of TCP/IP stack is Tcpip 5.10. You can find it here:
http://community.qnx.com/sf/wiki/do/viewPage/projects.qnx4/wiki/LatestSoftwareUpdates
> Do you have any ideas what could cause such a strange problem?
I don’t have ideas without output at least of sin in, sin ir, sin ar, sin ti, sin ver, show_pci -vvv. All outputs are needed before, after and during the problem occurs.
> Could several broadcast messages from other systems causes this kind of problems?
I’m not sure. Can you exclude impact of broadcast messages from other systems at testing time?
> Do you have an idea why not all systems are concerned?
I guess they are different or they have different environment. Do you have identical hardware on all systems?
> Do you have some tools beside netinfo, netsniff, netmap or netstat to analyze this kind of problem?
traceinfo, sin, monitor, netinfo
Respectfully,
Oleg
31 окт. 2016 г., в 16:14, Hans Lehmann(deleted) <community-noreply@qnx.com> написал:
> Hello,
>
> We had a strange problem with the system load which was caused be a socket at a customer. The Socket runs on priority 23 and there is no other process running at this priority.
> The socket is used for phindows sessions, network printing and remote service via Phindows.
>
> The time went wrong for some seconds within a minute produced by the system load (10-15%) of the socket.
>
> At this moment we try to analyze the problem there was no print job and only our phindows session established over the socket which was checked by netstat and the system load was checked by sac. We checked the system load directly on the node and from another node (sac –n). Furthermore we killed the phindows session to check whether phindows is the reason or not.
>
> We figured out that the socket causes this problem, because first we restarted several processes without any results and secondly there is no other process running on priority 23 as mentioned above. After restart of each process we checked the system time and saw that the time was wrong within a minute and the system load was to high.
> After restarting the socket the problem gone and the time is since that date ok and the system works proper without any system load or problems.
>
> We used Socket Version 4.25H on all machines at the customer but only on some machines this problem occurred.
>
>
> Do you have any ideas what could cause such a strange problem?
> Could several broadcast messages from other systems causes this kind of problems?
> Do you have an idea why not all systems are concerned?
> Do you have some tools beside netinfo, netsniff, netmap or netstat to analyze this kind of problem?
>
> Kendly reagrds
>
> Hans Lehmann
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post117033
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2016-10-31T18:43:20Zpost117033: system load problem caused by socket
http://community.qnx.com/sf/go/post117033
Hello,
We had a strange problem with the system load which was caused be a socket at a customer. The Socket runs on priority 23 and there is no other process running at this priority.
The socket is used for phindows sessions, network printing and remote service via Phindows.
The time went wrong for some seconds within a minute produced by the system load (10-15%) of the socket.
At this moment we try to analyze the problem there was no print job and only our phindows session established over the socket which was checked by netstat and the system load was checked by sac. We checked the system load directly on the node and from another node (sac –n). Furthermore we killed the phindows session to check whether phindows is the reason or not.
We figured out that the socket causes this problem, because first we restarted several processes without any results and secondly there is no other process running on priority 23 as mentioned above. After restart of each process we checked the system time and saw that the time was wrong within a minute and the system load was to high.
After restarting the socket the problem gone and the time is since that date ok and the system works proper without any system load or problems.
We used Socket Version 4.25H on all machines at the customer but only on some machines this problem occurred.
Do you have any ideas what could cause such a strange problem?
Could several broadcast messages from other systems causes this kind of problems?
Do you have an idea why not all systems are concerned?
Do you have some tools beside netinfo, netsniff, netmap or netstat to analyze this kind of problem?
Kendly reagrds
Hans LehmannHans Lehmann(deleted)2016-10-31T13:14:33Zpost116949: Re: SSDs and support for the ATA_TRIM command
http://community.qnx.com/sf/go/post116949
Hi Andy,
Currently we don't have plans to support TRIM in QNX 4. As a workaround you can use disk that isn't required the TRIM command.
Respectfully,
Oleg
5 окт. 2016 г., в 1:27:16, Andy Rhind <community-noreply@qnx.com> написал:
> Hi:
>
> I understand that there isn't support for the ATA_TRIM command for SSDs in QNX4. See http://www.qnx.com/support/knowledgebase.html?id=50114000000N4mM
>
> The Knowledge base talks about "The result will potentially be extremely slow filesystem performance. "
>
> Is there a workaround? or are there plans to support TRIM in the future?
>
> Thanks,
> Andy
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post116941
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2016-10-06T11:17:58Zpost116941: SSDs and support for the ATA_TRIM command
http://community.qnx.com/sf/go/post116941
Hi:
I understand that there isn't support for the ATA_TRIM command for SSDs in QNX4. See http://www.qnx.com/support/knowledgebase.html?id=50114000000N4mM
The Knowledge base talks about "The result will potentially be extremely slow filesystem performance. "
Is there a workaround? or are there plans to support TRIM in the future?
Thanks,
AndyAndy Rhind2016-10-04T22:27:16Zpost116937: Re: mb_map full
http://community.qnx.com/sf/go/post116937
Hi Oleg, thank you for your help. I search on internet and I found that there is a virus which is attacking telnet port 23 sending a lots of logins to crash the service. So, I changed the telnet port on Qnx, and I hope that that fix the problem. >Thanks again...
Victor.Victor Gamboa2016-10-03T17:34:52Zpost116933: Re: mb_map full
http://community.qnx.com/sf/go/post116933
Hi Victor,
Sorry for delay with my answer.
> 1432 1432 27 10o REPLY 21 20K login -h bd07c44d.virtua.com.br -p
> 854 854 16 10o REPLY 21 20K login -h static.vnpt.vn -p
> 2435 2435 32 10o REPLY 19 20K login -h 95.9.191.5.static.ttnet.com.tr -p
> 2521 2521 34 10o REPLY 19 20K login -h 55-140-164-181.fibertel.com.ar -p
This should be a login command that is launched from telnetd to establish remote connection. Is it possible that your QNX system has many telnet connections at one time?
Respectfully,
Oleg
30 сент. 2016 г., в 18:13:26, Victor Gamboa <community-noreply@qnx.com> написал:
> Hi Oleg, yes the machine es accessed via local network an via internet whith telnet. I use tcpip on qnx side and telnet client on client side.
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post116931
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2016-10-03T08:35:11Zpost116931: Re: mb_map full
http://community.qnx.com/sf/go/post116931
Hi Oleg, yes the machine es accessed via local network an via internet whith telnet. I use tcpip on qnx side and telnet client on client side.Victor Gamboa2016-09-30T15:13:26Zpost116930: Re: mb_map full
http://community.qnx.com/sf/go/post116930
Victor, do your system connect to network? What services did you run?
Respectfully,
Oleg
29 сент. 2016 г., в 18:26:04, Victor Gamboa <community-noreply@qnx.com> написал:
> Oleg I am viewing weird entries on Ps -A like this:
> 1432 1432 27 10o REPLY 21 20K login -h bd07c44d.virtua.com.br -p
> 854 854 16 10o REPLY 21 20K login -h static.vnpt.vn -p
> 2435 2435 32 10o REPLY 19 20K login -h 95.9.191.5.static.ttnet.com.tr -p
> 2521 2521 34 10o REPLY 19 20K login -h 55-140-164-181.fibertel.com.ar -p
> I guess this is related with the problem, like non autorized entries to qnx4 or a qnx4 virus ? Is it possible ? How can I block theese entries ?
> I really appreciate the help.
> Victor
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post116913
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2016-09-30T15:05:46Zpost116929: Re: mb_map full
http://community.qnx.com/sf/go/post116929
Hi Victor,
Try to increase the value twice.
Respectfully,
Oleg
29 сент. 2016 г., в 17:50:54, Victor Gamboa <community-noreply@qnx.com> написал:
> Hi Oleg, yes I am using tcpip 5.10. What is a good value to the -m option ?
> Thank you for the help.
> Victor
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post116908
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2016-09-30T15:02:23Zpost116913: Re: mb_map full
http://community.qnx.com/sf/go/post116913
Oleg I am viewing weird entries on Ps -A like this:
1432 1432 27 10o REPLY 21 20K login -h bd07c44d.virtua.com.br -p
854 854 16 10o REPLY 21 20K login -h static.vnpt.vn -p
2435 2435 32 10o REPLY 19 20K login -h 95.9.191.5.static.ttnet.com.tr -p
2521 2521 34 10o REPLY 19 20K login -h 55-140-164-181.fibertel.com.ar -p
I guess this is related with the problem, like non autorized entries to qnx4 or a qnx4 virus ? Is it possible ? How can I block theese entries ?
I really appreciate the help.
VictorVictor Gamboa2016-09-29T15:26:04Zpost116908: Re: mb_map full
http://community.qnx.com/sf/go/post116908
Hi Oleg, yes I am using tcpip 5.10. What is a good value to the -m option ?
Thank you for the help.
VictorVictor Gamboa2016-09-29T14:50:54Zpost116905: Re: mb_map full
http://community.qnx.com/sf/go/post116905
Hi Victor,
What TCP stack do you use? I'm assuming Tcpip 5.10. Try to increase the number of memory pools in first argument of -m option of Tcpip. Default value for this option is 64,65535.
Respectfully,
Oleg
29 сент. 2016 г., в 3:49:57, Victor Gamboa <community-noreply@qnx.com> написал:
> Hi, I really appreciate any help on this, I receveid the message on the subject and no one on the network can access QNX . I have to reset the server to get acces again. This is happening many times during the day and with some of my costumers who have qnx4. This begins to happen a few days ago. Thank you for any help.
> Victor
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post116904
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2016-09-29T08:08:31Zpost116904: mb_map full
http://community.qnx.com/sf/go/post116904
Hi, I really appreciate any help on this, I receveid the message on the subject and no one on the network can access QNX . I have to reset the server to get acces again. This is happening many times during the day and with some of my costumers who have qnx4. This begins to happen a few days ago. Thank you for any help.
VictorVictor Gamboa2016-09-29T00:49:57Zpost116811: Re: Disk Errors are cached?
http://community.qnx.com/sf/go/post116811
Hi Andy,
> 1) I see that dcheck has a 'disable drive error correction' options. Is this a suitable candidate ?
It seems that this has sense for Fsys.ata only (old driver) to disable ECC check.
> 2) Is there an ioctl() that will do the cache invalidation?
Did you try sync utility to flush caches? Did it help?
> 3) Is all this caused by Fsys.Fsys.atapi caching I/O Errors when they shouldn't be cached.? If so can that behavior be stopped?
Disk cache is driven by Fsys, not the disk driver. I can't know how to disable caching in this particular case.
> We have the source and the error happens in one place. If we could invalidate the cache , retry and move on (or not if its a real error) . This would help production and allow us time to get the best replacement.
I understand this. Unfortunately, I can't debug the issue without the ability to reproduce it. And even more the debugging may take quite a few time.
Respectfully,
Oleg
19 сент. 2016 г., в 9:44:55, Andy Rhind <community-noreply@qnx.com> написал:
> Oleg:
>
> Yes II agree the original problem is hard to reproduce and 5 days is forever, if testing. 5 days is a very short time in production. I believe the problem is the Commell with the motherboard. Finding a QNX4 compatible replacement will take time and cost, then it needs to be tested for the current problem. We have a possible replacement for the ARaid, but testing is ongoing.
>
> Sure the original, temporary I/O Error happens and is a bad thing and needs to be stopped. I posted here to try to understand the stickyness of the error, to understand its reason and find a way to get around it in the short term.
>
> We have the source and the error happens in one place. If we could invalidate the cache , retry and move on (or not if its a real error) . This would help production and allow us time to get the best replacement.
>
> 1) I see that dcheck has a 'disable drive error correction' options. Is this a suitable candidate ?
>
> 2) Is there an ioctl() that will do the cache invalidation?
>
> 3) Is all this caused by Fsys.Fsys.atapi caching I/O Errors when they shouldn't be cached.? If so can that behavior be stopped?
>
>
> Thanks,
> Andy
>
>
>
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post116810
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2016-09-19T08:54:05Zpost116810: Re: Disk Errors are cached?
http://community.qnx.com/sf/go/post116810
Oleg:
Yes II agree the original problem is hard to reproduce and 5 days is forever, if testing. 5 days is a very short time in production. I believe the problem is the Commell with the motherboard. Finding a QNX4 compatible replacement will take time and cost, then it needs to be tested for the current problem. We have a possible replacement for the ARaid, but testing is ongoing.
Sure the original, temporary I/O Error happens and is a bad thing and needs to be stopped. I posted here to try to understand the stickyness of the error, to understand its reason and find a way to get around it in the short term.
We have the source and the error happens in one place. If we could invalidate the cache , retry and move on (or not if its a real error) . This would help production and allow us time to get the best replacement.
1) I see that dcheck has a 'disable drive error correction' options. Is this a suitable candidate ?
2) Is there an ioctl() that will do the cache invalidation?
3) Is all this caused by Fsys.Fsys.atapi caching I/O Errors when they shouldn't be cached.? If so can that behavior be stopped?
Thanks,
AndyAndy Rhind2016-09-19T06:44:55Zpost116801: Re: Disk Errors are cached?
http://community.qnx.com/sf/go/post116801
Hi Andy,
It seems that this issue can't be explored without hardware. It's too difficult to reproduce it (up to 5 days). Can you replace hardware as a workaround?
Respectfully,
Oleg
15 сент. 2016 г., в 7:08:57, Andy Rhind <community-noreply@qnx.com> написал:
> Oleg:
>
> I wish I could easily reproduce it . It seems to happen when their Raima database does a purge. I've tried to create scripts that simulate the original fault but cant do it. The customer has a process that floods the db and causes it to purge often. This causes the real I/O error somewhere between 1 and 5 days.
>
> Interestingly this is only happening since we changed the motherboard to a Commell AS-C74. The original motherboard is now EOL. We also use an Accordance ARaid. There two together are necessary to produce the error.
>
> We don't have an easy way to create the original error.
>
> Andy
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post116790
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2016-09-16T12:48:06Zpost116790: Re: Disk Errors are cached?
http://community.qnx.com/sf/go/post116790
Oleg:
I wish I could easily reproduce it . It seems to happen when their Raima database does a purge. I've tried to create scripts that simulate the original fault but cant do it. The customer has a process that floods the db and causes it to purge often. This causes the real I/O error somewhere between 1 and 5 days.
Interestingly this is only happening since we changed the motherboard to a Commell AS-C74. The original motherboard is now EOL. We also use an Accordance ARaid. There two together are necessary to produce the error.
We don't have an easy way to create the original error.
AndyAndy Rhind2016-09-15T04:08:57Zpost116778: Re: Disk Errors are cached?
http://community.qnx.com/sf/go/post116778
Hi Andy,
Did you get this issue on the one particular disk / controller? Or did it occur on different hardware? How can I reproduce the issue?
Respectfully,
Oleg
14 сент. 2016 г., в 6:16:31, Andy Rhind <community-noreply@qnx.com> написал:
> Oleg:
>
> Thanks for this. Attached are two screen pictures taken from traceinfo.. The 7th of Aug is when the clients application spotted the error. Since most of their system was still running, eventually (5 minutes) the bad block disappeared.
>
> The 11th of September was caught using only a test program. This one is 30 minutes after the initial error. the trace lines are caused by my using spatch to examine the block.
>
> So far I've looked for ways to flush or clear the cache, including sync and ioctl() calls
>
> Thanks,
> ]Andy
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post116777
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
> <20160912_104032.jpg><20160807_182436.jpg>Oleg Bolshakov2016-09-14T07:43:20Zpost116777: Re: Disk Errors are cached?
http://community.qnx.com/sf/go/post116777
Oleg:
Thanks for this. Attached are two screen pictures taken from traceinfo.. The 7th of Aug is when the clients application spotted the error. Since most of their system was still running, eventually (5 minutes) the bad block disappeared.
The 11th of September was caught using only a test program. This one is 30 minutes after the initial error. the trace lines are caused by my using spatch to examine the block.
So far I've looked for ways to flush or clear the cache, including sync and ioctl() calls
Thanks,
]AndyAndy Rhind2016-09-14T03:16:31Zpost116772: Re: Disk Errors are cached?
http://community.qnx.com/sf/go/post116772
Hi Andy,
This may be an issue in Fsys. I'll look deeply at this. Can you post here all Fsys traceinfo messages?
Respectfully,
Oleg
12 сент. 2016 г., в 5:24:54, Andy Rhind <community-noreply@qnx.com> написал:
> HI:
>
> I have a QNX4 system running Fsys 4.24Z and Fsys.atapi 4.25G .
> Fsys is started with "Fsys -H disk80 -r 512 -c64M"
>
> There is a problem with the motherboard and disk that causes them to rarely throw an error 5 .
> Traceinfo says -->
> "Sept 11 11:45:02 2 00003001 Bad Block 00C1ECE9 on /dev/hd0 flagged in cache"
>
> I stop the test program and there is no other disk activity.
> spatch /dev/hd0 c1ece9 reports a bad block
> dcheck -f 12709097 -b2 /dev/hd0 also reports the bad block.
> They consistently return the error for the the next 30 minutes.
>
> Then when I do a dcheck that scans more than 64MB (see Fsys's startup params) of disk the error goes away. Also a full dcheck reports all blocks as OK.
>
> When I check the disks SMART stats. There are 1) no relocated sectors, 2) no reallocation events ,3) no Current Pending sectors and 4) no Un-correctable sectors. The disk looks perfect.
>
> It seems I have two problems.
> 1) The one that caused a false reporting of an I/O error (5) on write. This is probably a single occurrence.
> 2) The I/O error seems to have been cached and when retried the cached failure is returned. Which makes recovery/retry code fail.
>
> Yes the I/O error is not a good thing and is begin looked into, but that research is made much harder by the caching of the error.
>
> Does my analysis sound correct? and if so is there a way to stop Fsys/Fsys.atapi caching the disk error.?
>
> Thanks,
> Andy
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post116768
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2016-09-13T11:22:17Zpost116768: Disk Errors are cached?
http://community.qnx.com/sf/go/post116768
HI:
I have a QNX4 system running Fsys 4.24Z and Fsys.atapi 4.25G .
Fsys is started with "Fsys -H disk80 -r 512 -c64M"
There is a problem with the motherboard and disk that causes them to rarely throw an error 5 .
Traceinfo says -->
"Sept 11 11:45:02 2 00003001 Bad Block 00C1ECE9 on /dev/hd0 flagged in cache"
I stop the test program and there is no other disk activity.
spatch /dev/hd0 c1ece9 reports a bad block
dcheck -f 12709097 -b2 /dev/hd0 also reports the bad block.
They consistently return the error for the the next 30 minutes.
Then when I do a dcheck that scans more than 64MB (see Fsys's startup params) of disk the error goes away. Also a full dcheck reports all blocks as OK.
When I check the disks SMART stats. There are 1) no relocated sectors, 2) no reallocation events ,3) no Current Pending sectors and 4) no Un-correctable sectors. The disk looks perfect.
It seems I have two problems.
1) The one that caused a false reporting of an I/O error (5) on write. This is probably a single occurrence.
2) The I/O error seems to have been cached and when retried the cached failure is returned. Which makes recovery/retry code fail.
Yes the I/O error is not a good thing and is begin looked into, but that research is made much harder by the caching of the error.
Does my analysis sound correct? and if so is there a way to stop Fsys/Fsys.atapi caching the disk error.?
Thanks,
AndyAndy Rhind2016-09-12T02:24:53Zpost116381: RE: Regular Expressions issue with meta character "." usage for UTF-8 Chinese Characters
http://community.qnx.com/sf/go/post116381
Hello Oleg,
I just realized you were responding to the question I posted on the Discussion board.
I had in fact already created a case (00151453) in the Technical Support Portal using our Silver Support Plan. The case has all the right fields populated.
I hope that should work for now.
Thanks,
Raj
-----Original Message-----
From: Олег Большаков [mailto:community-noreply@qnx.com]
Sent: Friday, June 03, 2016 6:30 PM
To: qnx4-community@community.qnx.com
Cc: Mudiam, Veni (GE Transportation); Paritosh, Prakarsh (GE Transportation); Chauhan, Shivali (GE Transportation); Mudiam, Veni (GE Transportation); Paritosh, Prakarsh (GE Transportation); Chauhan, Shivali (GE Transportation)
Subject: EXT: Re: Regular Expressions issue with meta character "." usage for UTF-8 Chinese Characters
This is discussion board for QNX 4. You have to post your question about QNX 6.3.2 in appropriate discussion board.
Respectfully,
Oleg
3 июня 2016 г., в 15:42:14, Bhumagani, Rajani Kanth (GE Transportation) <community-noreply@qnx.com> написал:
> Hello Oleg,
>
> Can you please clarify what the other regular expressions are available for QNX 6.3.2 platform..
>
> Are these in some existing libraries that we can download from the foundry. If yes can you please let us know which ones they are or share the link.
>
> Thanks,
> Raj
>
> -----Original Message-----
> From: Олег Большаков [mailto:community-noreply@qnx.com]
> Sent: Friday, June 03, 2016 6:02 PM
> To: qnx4-community@community.qnx.com
> Cc: Mudiam, Veni (GE Transportation); Paritosh, Prakarsh (GE Transportation); Chauhan, Shivali (GE Transportation); Mudiam, Veni (GE Transportation); Paritosh, Prakarsh (GE Transportation); Chauhan, Shivali (GE Transportation)
> Subject: EXT: Re: Regular Expressions issue with meta character "." usage for UTF-8 Chinese Characters
>
> Hi Raj,
>
>
>
> Both regcomp() and regexec() work with 8bit characters. So one . (dot) matches only one 8bit character or 1 byte. The 车 has 3 byte UTF-8 code 0xE8 0xBD 0xA6. So you have to match 车 as three dots (…) or use another regular expression.
>
>
>
> Respectfully,
>
> Oleg
>
>
>
> 1 июня 2016 г., в 18:20:00, Raj Bhumagani <community-noreply@qnx.com> написал:
>
>
>
>> Hello,
>
>>
>
>> I am using regcomp and regexec for matching Chinese UTF-8 strings with Chinese UTF-8 regular expressions.
>
>>
>
>> When I use the following regular expression there is a match
>
>> String to match : "火车a"
>
>> Regular Expression : ^(火车.)$
>
>>
>
>> The "." in the regular expression correctly matches the "a" in the string
>
>>
>
>> However when I use the following regular expression there is NO match. (it should have matched)
>
>>
>
>> String to match : "火车车"
>
>> Regular Expression : ^(火车.)$
>
>>
>
>> The "." in the regular expression should have matched the 3rd chinese character "车" in the string... but it is NOT.
>
>>
>
>> However I observed that the following returns a match:
>
>> String to match : "火车车"
>
>> Regular Expression : ^(火车...)$
>
>>
>
>> Essentially I had to put 3 "." i.e. "..." instead of a single "." for the regular expression to match.
>
>>
>
>> However a single "." should essentially match any character be it Chinese or ASCII..
>
>>
>
>> Can someone please tell me what needs to be done so that I can use a single "." character to match.
>
>>
>
>> thanks,
>
>> Raj
>
>>
>
>>
>
>>
>
>>
>
>>
>
>> _______________________________________________
>
>>
>
>> QNX4 Community Support
>
>> https://urldefense.proofpoint.com/v2/url?u=http-3A__community.qnx.com_sf_go_post116376&d=CwIGaQ&c=IV_clAzoPDE253xZdHuilRgztyh_RiV3wUrLrDQYWSI&r=Qkq3thnwMzV5zVsxn1O85oHu8Ax_ML0WYHSrWEFY7uE&m=Py3dmmDDlagc-AleG_s_dkZyRptg1CnN6pGRYYXHNLQ&s=GMqWisSCWU34xK7-hsTmAge_Afj0N3R7-Fra3qKeiR0&e=
>
>> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
>
>
>
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> https://urldefense.proofpoint.com/v2/url?u=http-3A__community.qnx.com_sf_go_post116378&d=CwIGaQ&c=IV_clAzoPDE253xZdHuilRgztyh_RiV3wUrLrDQYWSI&r=Qkq3thnwMzV5zVsxn1O85oHu8Ax_ML0WYHSrWEFY7uE&m=Py3dmmDDlagc-AleG_s_dkZyRptg1CnN6pGRYYXHNLQ&s=CbptcN5d9BouJTUg8Vx0heUG0vzx53gwrBcn1OoCiD0&e=
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> https://urldefense.proofpoint.com/v2/url?u=http-3A__community.qnx.com_sf_go_post116379&d=CwIGaQ&c=IV_clAzoPDE253xZdHuilRgztyh_RiV3wUrLrDQYWSI&r=Qkq3thnwMzV5zVsxn1O85oHu8Ax_ML0WYHSrWEFY7uE&m=QcCFI6yMBXJoQrGHNM9y5eRlihiuDoacWC_-KioK4PU&s=Gp0qlFJZuG_p1pcrFTOxdtpJ3TlfCQOrgJmTnqpZsG8&e=
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
_______________________________________________
QNX4 Community Support
https://urldefense.proofpoint.com/v2/url?u=http-3A__community.qnx.com_sf_go_post116380&d=CwIGaQ&c=IV_clAzoPDE253xZdHuilRgztyh_RiV3wUrLrDQYWSI&r=Qkq3thnwMzV5zVsxn1O85oHu8Ax_ML0WYHSrWEFY7uE&m=QcCFI6yMBXJoQrGHNM9y5eRlihiuDoacWC_-KioK4PU&s=Texl74wk4hc6koGrpQyFuOGFJcK1Laq4AU08i5H6DN4&e=
To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comRaj Bhumagani(deleted)2016-06-03T13:10:57Zpost116380: Re: Regular Expressions issue with meta character "." usage for UTF-8 Chinese Characters
http://community.qnx.com/sf/go/post116380
This is discussion board for QNX 4. You have to post your question about QNX 6.3.2 in appropriate discussion board.
Respectfully,
Oleg
3 июня 2016 г., в 15:42:14, Bhumagani, Rajani Kanth (GE Transportation) <community-noreply@qnx.com> написал:
> Hello Oleg,
>
> Can you please clarify what the other regular expressions are available for QNX 6.3.2 platform..
>
> Are these in some existing libraries that we can download from the foundry. If yes can you please let us know which ones they are or share the link.
>
> Thanks,
> Raj
>
> -----Original Message-----
> From: Олег Большаков [mailto:community-noreply@qnx.com]
> Sent: Friday, June 03, 2016 6:02 PM
> To: qnx4-community@community.qnx.com
> Cc: Mudiam, Veni (GE Transportation); Paritosh, Prakarsh (GE Transportation); Chauhan, Shivali (GE Transportation); Mudiam, Veni (GE Transportation); Paritosh, Prakarsh (GE Transportation); Chauhan, Shivali (GE Transportation)
> Subject: EXT: Re: Regular Expressions issue with meta character "." usage for UTF-8 Chinese Characters
>
> Hi Raj,
>
>
>
> Both regcomp() and regexec() work with 8bit characters. So one . (dot) matches only one 8bit character or 1 byte. The 车 has 3 byte UTF-8 code 0xE8 0xBD 0xA6. So you have to match 车 as three dots (…) or use another regular expression.
>
>
>
> Respectfully,
>
> Oleg
>
>
>
> 1 июня 2016 г., в 18:20:00, Raj Bhumagani <community-noreply@qnx.com> написал:
>
>
>
>> Hello,
>
>>
>
>> I am using regcomp and regexec for matching Chinese UTF-8 strings with Chinese UTF-8 regular expressions.
>
>>
>
>> When I use the following regular expression there is a match
>
>> String to match : "火车a"
>
>> Regular Expression : ^(火车.)$
>
>>
>
>> The "." in the regular expression correctly matches the "a" in the string
>
>>
>
>> However when I use the following regular expression there is NO match. (it should have matched)
>
>>
>
>> String to match : "火车车"
>
>> Regular Expression : ^(火车.)$
>
>>
>
>> The "." in the regular expression should have matched the 3rd chinese character "车" in the string... but it is NOT.
>
>>
>
>> However I observed that the following returns a match:
>
>> String to match : "火车车"
>
>> Regular Expression : ^(火车...)$
>
>>
>
>> Essentially I had to put 3 "." i.e. "..." instead of a single "." for the regular expression to match.
>
>>
>
>> However a single "." should essentially match any character be it Chinese or ASCII..
>
>>
>
>> Can someone please tell me what needs to be done so that I can use a single "." character to match.
>
>>
>
>> thanks,
>
>> Raj
>
>>
>
>>
>
>>
>
>>
>
>>
>
>> _______________________________________________
>
>>
>
>> QNX4 Community Support
>
>> https://urldefense.proofpoint.com/v2/url?u=http-3A__community.qnx.com_sf_go_post116376&d=CwIGaQ&c=IV_clAzoPDE253xZdHuilRgztyh_RiV3wUrLrDQYWSI&r=Qkq3thnwMzV5zVsxn1O85oHu8Ax_ML0WYHSrWEFY7uE&m=Py3dmmDDlagc-AleG_s_dkZyRptg1CnN6pGRYYXHNLQ&s=GMqWisSCWU34xK7-hsTmAge_Afj0N3R7-Fra3qKeiR0&e=
>
>> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
>
>
>
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> https://urldefense.proofpoint.com/v2/url?u=http-3A__community.qnx.com_sf_go_post116378&d=CwIGaQ&c=IV_clAzoPDE253xZdHuilRgztyh_RiV3wUrLrDQYWSI&r=Qkq3thnwMzV5zVsxn1O85oHu8Ax_ML0WYHSrWEFY7uE&m=Py3dmmDDlagc-AleG_s_dkZyRptg1CnN6pGRYYXHNLQ&s=CbptcN5d9BouJTUg8Vx0heUG0vzx53gwrBcn1OoCiD0&e=
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post116379
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2016-06-03T13:01:08Zpost116379: RE: Regular Expressions issue with meta character "." usage for UTF-8 Chinese Characters
http://community.qnx.com/sf/go/post116379
Hello Oleg,
Can you please clarify what the other regular expressions are available for QNX 6.3.2 platform..
Are these in some existing libraries that we can download from the foundry. If yes can you please let us know which ones they are or share the link.
Thanks,
Raj
-----Original Message-----
From: Олег Большаков [mailto:community-noreply@qnx.com]
Sent: Friday, June 03, 2016 6:02 PM
To: qnx4-community@community.qnx.com
Cc: Mudiam, Veni (GE Transportation); Paritosh, Prakarsh (GE Transportation); Chauhan, Shivali (GE Transportation); Mudiam, Veni (GE Transportation); Paritosh, Prakarsh (GE Transportation); Chauhan, Shivali (GE Transportation)
Subject: EXT: Re: Regular Expressions issue with meta character "." usage for UTF-8 Chinese Characters
Hi Raj,
Both regcomp() and regexec() work with 8bit characters. So one . (dot) matches only one 8bit character or 1 byte. The 车 has 3 byte UTF-8 code 0xE8 0xBD 0xA6. So you have to match 车 as three dots (…) or use another regular expression.
Respectfully,
Oleg
1 июня 2016 г., в 18:20:00, Raj Bhumagani <community-noreply@qnx.com> написал:
> Hello,
>
> I am using regcomp and regexec for matching Chinese UTF-8 strings with Chinese UTF-8 regular expressions.
>
> When I use the following regular expression there is a match
> String to match : "火车a"
> Regular Expression : ^(火车.)$
>
> The "." in the regular expression correctly matches the "a" in the string
>
> However when I use the following regular expression there is NO match. (it should have matched)
>
> String to match : "火车车"
> Regular Expression : ^(火车.)$
>
> The "." in the regular expression should have matched the 3rd chinese character "车" in the string... but it is NOT.
>
> However I observed that the following returns a match:
> String to match : "火车车"
> Regular Expression : ^(火车...)$
>
> Essentially I had to put 3 "." i.e. "..." instead of a single "." for the regular expression to match.
>
> However a single "." should essentially match any character be it Chinese or ASCII..
>
> Can someone please tell me what needs to be done so that I can use a single "." character to match.
>
> thanks,
> Raj
>
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> https://urldefense.proofpoint.com/v2/url?u=http-3A__community.qnx.com_sf_go_post116376&d=CwIGaQ&c=IV_clAzoPDE253xZdHuilRgztyh_RiV3wUrLrDQYWSI&r=Qkq3thnwMzV5zVsxn1O85oHu8Ax_ML0WYHSrWEFY7uE&m=Py3dmmDDlagc-AleG_s_dkZyRptg1CnN6pGRYYXHNLQ&s=GMqWisSCWU34xK7-hsTmAge_Afj0N3R7-Fra3qKeiR0&e=
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
_______________________________________________
QNX4 Community Support
https://urldefense.proofpoint.com/v2/url?u=http-3A__community.qnx.com_sf_go_post116378&d=CwIGaQ&c=IV_clAzoPDE253xZdHuilRgztyh_RiV3wUrLrDQYWSI&r=Qkq3thnwMzV5zVsxn1O85oHu8Ax_ML0WYHSrWEFY7uE&m=Py3dmmDDlagc-AleG_s_dkZyRptg1CnN6pGRYYXHNLQ&s=CbptcN5d9BouJTUg8Vx0heUG0vzx53gwrBcn1OoCiD0&e=
To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comRaj Bhumagani(deleted)2016-06-03T12:42:54Zpost116378: Re: Regular Expressions issue with meta character "." usage for UTF-8 Chinese Characters
http://community.qnx.com/sf/go/post116378
Hi Raj,
Both regcomp() and regexec() work with 8bit characters. So one . (dot) matches only one 8bit character or 1 byte. The 车 has 3 byte UTF-8 code 0xE8 0xBD 0xA6. So you have to match 车 as three dots (…) or use another regular expression.
Respectfully,
Oleg
1 июня 2016 г., в 18:20:00, Raj Bhumagani <community-noreply@qnx.com> написал:
> Hello,
>
> I am using regcomp and regexec for matching Chinese UTF-8 strings with Chinese UTF-8 regular expressions.
>
> When I use the following regular expression there is a match
> String to match : "火车a"
> Regular Expression : ^(火车.)$
>
> The "." in the regular expression correctly matches the "a" in the string
>
> However when I use the following regular expression there is NO match. (it should have matched)
>
> String to match : "火车车"
> Regular Expression : ^(火车.)$
>
> The "." in the regular expression should have matched the 3rd chinese character "车" in the string... but it is NOT.
>
> However I observed that the following returns a match:
> String to match : "火车车"
> Regular Expression : ^(火车...)$
>
> Essentially I had to put 3 "." i.e. "..." instead of a single "." for the regular expression to match.
>
> However a single "." should essentially match any character be it Chinese or ASCII..
>
> Can someone please tell me what needs to be done so that I can use a single "." character to match.
>
> thanks,
> Raj
>
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post116376
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2016-06-03T12:33:28Zpost116376: Regular Expressions issue with meta character "." usage for UTF-8 Chinese Characters
http://community.qnx.com/sf/go/post116376
Hello,
I am using regcomp and regexec for matching Chinese UTF-8 strings with Chinese UTF-8 regular expressions.
When I use the following regular expression there is a match
String to match : "火车a"
Regular Expression : ^(火车.)$
The "." in the regular expression correctly matches the "a" in the string
However when I use the following regular expression there is NO match. (it should have matched)
String to match : "火车车"
Regular Expression : ^(火车.)$
The "." in the regular expression should have matched the 3rd chinese character "车" in the string... but it is NOT.
However I observed that the following returns a match:
String to match : "火车车"
Regular Expression : ^(火车...)$
Essentially I had to put 3 "." i.e. "..." instead of a single "." for the regular expression to match.
However a single "." should essentially match any character be it Chinese or ASCII..
Can someone please tell me what needs to be done so that I can use a single "." character to match.
thanks,
RajRaj Bhumagani(deleted)2016-06-01T15:20:00Zpost116017: Re: None
http://community.qnx.com/sf/go/post116017
Hi Dodi,
You can determine the MAC using ifconfig -a or netinfo -l commands.
Respectfully,
Oleg
24 марта 2016 г., в 9:04, edwin rinjani <community-noreply@qnx.com> написал:
> hallo oleg,
> I have to say thank you very very much to you because you have gave me
> that driver, the driver is working properly and know i can find out what
> is the mac address of the network card.
> once again i say thank you very much, because i have been a week to looking
> for the right driver .
>
> Respectfully,
> dodi s
>
> 2016-03-23 22:34 GMT+07:00 Олег Большаков <community-noreply@qnx.com>:
>
>> Hi Dodi,
>>
>> You have to use Net.e1000 driver instead of Net.i82540. The Net.e1000 is a
>> new driver that should support all hardware from Net.i82540. Attaching the
>> latest Net.e1000 build.
>>
>> Respectfully,
>> Oleg
>>
>> 22 марта 2016 г., в 13:09, edwin rinjani <community-noreply@qnx.com>
>> написал:
>>
>>> hello,
>>> sorry the driver i have found not Net.ether82540 but *Net.i82540, *
>>> i hope som body can help me where can i download that driver…
>>> thanks
>>>
>>> regards,
>>> dodi s
>>>
>>> 2016-03-22 17:03 GMT+07:00 edwin rinjani <edwinrinjani@gmail.com>:
>>>
>>>> hello,
>>>> i saw the qnx hardware support at :
>>>>
>>>>
>>>>
>> http://www.qnx.com/developers/hardware_support/qnx4/qnx4hardware.html?category=Network
>>>>
>>>> i need the driver for Intel RC 82540EM network adapter, at the following
>>>> address i have found that the driver is Net.ether82540, but where can i
>>>> download that driver, i hope some body can help me please...
>>>>
>>>> regards,
>>>> dodi s
>>>>
>>>> 2016-03-18 20:44 GMT+07:00 Олег Большаков <community-noreply@qnx.com>:
>>>>
>>>>> Hello,
>>>>>
>>>>> Please specify the controller's name and PCI IDs (use show_pci -vv in
>>>>> QNX4 console).
>>>>>
>>>>> Respectfully,
>>>>> Oleg
>>>>>
>>>>> 18 марта 2016 г., в 9:32:57, edwin rinjani <community-noreply@qnx.com>
>>>>> написал:
>>>>>
>>>>>> dear sir,
>>>>>> I am an user of qnx 4.25 and we need driver for network card, we have
>>>>> read the qnx 4 support network driver and i saw the status has
>> released,
>>>>> but i still confused where can i download the driver that has been
>> released.
>>>>>> can anybody give me a clue please.
>>>>>> thank you
>>>>>>
>>>>>> regards,
>>>>>> dodi s
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>>
>>>>> QNX4 Community Support
>>>>> http://community.qnx.com/sf/go/post115979
>>>>> To cancel your subscription to this discussion, please e-mail
>>>>> qnx4-community-unsubscribe@community.qnx.com
>>>>>
>>>>
>>>>
>>>
>>>
>>>
>>>
>>> _______________________________________________
>>>
>>> QNX4 Community Support
>>> http://community.qnx.com/sf/go/post115992
>>> To cancel your subscription to this discussion, please e-mail
>> qnx4-community-unsubscribe@community.qnx.com
>>> hello,
>>> sorry the driver i have found not Net.ether82540 but Net.i82540,
>>> i hope som body can help me where can i download that driver…
>>> thanks
>>>
>>> regards,
>>> dodi s
>>>
>>> 2016-03-22 17:03 GMT+07:00 edwin rinjani <edwinrinjani@gmail.com>:
>>> hello,
>>> i saw the qnx hardware support at :
>>>
>>>
>> http://www.qnx.com/developers/hardware_support/qnx4/qnx4hardware.html?category=Network
>>>
>>> i need the driver for Intel RC 82540EM network adapter, at the following
>> address i have found that the driver is Net.ether82540, but where can i
>> download that driver, i hope some body can help me please...
>>>
>>> regards,
>>> dodi s
>>>
>>> 2016-03-18 20:44 GMT+07:00 Олег Большаков <community-noreply@qnx.com>:
>>> Hello,
>>>
>>> Please specify the controller's name and PCI IDs (use show_pci -vv in
>> QNX4 console).
>>>
>>> Respectfully,
>>> Oleg
>>>
>>> 18 марта 2016 г., в 9:32:57, edwin rinjani <community-noreply@qnx.com>
>> написал:
>>>
>>>> dear sir,
>>>> I am an user of qnx 4.25 and we need driver for network card, we have
>> read the qnx 4 support network driver and i saw the status has released,
>> but i still confused where can i download the driver that has been released.
>>>> can anybody give me a clue please.
>>>> thank you
>>>>
>>>> regards,
>>>> dodi s
>>>
>>>
>>>
>>>
>>>
>>> _______________________________________________
>>>
>>> QNX4 Community Support
>>> http://community.qnx.com/sf/go/post115979
>>> To cancel your subscription to this discussion, please e-mail
>> qnx4-community-unsubscribe@community.qnx.com
>>>
>>>
>>
>>
>>
>>
>> _______________________________________________
>>
>> QNX4 Community Support
>> http://community.qnx.com/sf/go/post116012
>> To cancel your subscription to this discussion, please e-mail
>> qnx4-community-unsubscribe@community.qnx.com
>>
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post116016
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
> hallo oleg,
> I have to say thank you very very much to you because you have gave me that driver, the driver is working properly and know i can find out what is the mac address of the network card.
> once again i say thank you very much, because i have been a week to looking for the right driver .
>
> Respectfully,
> dodi s
>
> 2016-03-23 22:34 GMT+07:00 Олег Большаков <community-noreply@qnx.com>:
> Hi Dodi,
>
> You have to use Net.e1000 driver instead of Net.i82540. The Net.e1000 is a new driver that should support all hardware from Net.i82540. Attaching the latest Net.e1000 build.
>
> Respectfully,
> Oleg
>
> 22 марта 2016 г., в 13:09, edwin rinjani <community-noreply@qnx.com> написал:
>
> > hello,
> > sorry the driver i have found not Net.ether82540 but *Net.i82540, *
> > i hope som body can help me where can i download that driver…
> > thanks
> >
> > regards,
> > dodi s
> >
> > 2016-03-22 17:03 GMT+07:00 edwin rinjani <edwinrinjani@gmail.com>:
> >
> >> hello,
> >> i saw the qnx hardware support at :
> >>
> >>
> >> http://www.qnx.com/developers/hardware_support/qnx4/qnx4hardware.html?category=Network
> >>
> >> i need the driver for Intel RC 82540EM network adapter, at the following
> >> address i have found that the driver is Net.ether82540, but where can i
> >> download that driver, i hope some body can help me please...
> >>
> >> regards,
> >> dodi s
> >>
> >> 2016-03-18 20:44 GMT+07:00 Олег Большаков <community-noreply@qnx.com>:
> >>
> >>> Hello,
> >>>
> >>> Please specify the controller's name and PCI IDs (use show_pci -vv in
> >>> QNX4 console).
> >>>
> >>> Respectfully,
> >>> Oleg
> >>>
> >>> 18 марта 2016 г., в 9:32:57, edwin rinjani <community-noreply@qnx.com>
> >>> написал:
> >>>
> >>>> dear sir,
> >>>> I am an user of qnx 4.25 and we need driver for network card, we have
> >>> read the qnx 4 support network driver and i saw the status has released,
> >>> but i still confused where can i download the driver that has been released.
> >>>> can anybody give me a clue please.
> >>>> thank you
> >>>>
> >>>> regards,
> >>>> dodi s
> >>>
> >>>
> >>>
> >>>
> >>>
> >>> _______________________________________________
> >>>
> >>> QNX4 Community Support
> >>> http://community.qnx.com/sf/go/post115979
> >>> To cancel your subscription to this discussion, please e-mail
> >>> qnx4-community-unsubscribe@community.qnx.com
> >>>
> >>
> >>
> >
> >
> >
> >
> > _______________________________________________
> >
> > QNX4 Community Support
> > http://community.qnx.com/sf/go/post115992
> > To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
> > hello,
> > sorry the driver i have found not Net.ether82540 but Net.i82540,
> > i hope som body can help me where can i download that driver…
> > thanks
> >
> > regards,
> > dodi s
> >
> > 2016-03-22 17:03 GMT+07:00 edwin rinjani <edwinrinjani@gmail.com>:
> > hello,
> > i saw the qnx hardware support at :
> >
> > http://www.qnx.com/developers/hardware_support/qnx4/qnx4hardware.html?category=Network
> >
> > i need the driver for Intel RC 82540EM network adapter, at the following address i have found that the driver is Net.ether82540, but where can i download that driver, i hope some body can help me please...
> >
> > regards,
> > dodi s
> >
> > 2016-03-18 20:44 GMT+07:00 Олег Большаков <community-noreply@qnx.com>:
> > Hello,
> >
> > Please specify the controller's name and PCI IDs (use show_pci -vv in QNX4 console).
> >
> > Respectfully,
> > Oleg
> >
> > 18 марта 2016 г., в 9:32:57, edwin rinjani <community-noreply@qnx.com> написал:
> >
> > > dear sir,
> > > I am an user of qnx 4.25 and we need driver for network card, we have read the qnx 4 support network driver and i saw the status has released, but i still confused where can i download the driver that has been released.
> > > can anybody give me a clue please.
> > > thank you
> > >
> > > regards,
> > > dodi s
> >
> >
> >
> >
> >
> > _______________________________________________
> >
> > QNX4 Community Support
> > http://community.qnx.com/sf/go/post115979
> > To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
> >
> >
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post116012
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2016-03-24T08:44:05Zpost116016: Re: None
http://community.qnx.com/sf/go/post116016
hallo oleg,
I have to say thank you very very much to you because you have gave me
that driver, the driver is working properly and know i can find out what
is the mac address of the network card.
once again i say thank you very much, because i have been a week to looking
for the right driver .
Respectfully,
dodi s
2016-03-23 22:34 GMT+07:00 Олег Большаков <community-noreply@qnx.com>:
> Hi Dodi,
>
> You have to use Net.e1000 driver instead of Net.i82540. The Net.e1000 is a
> new driver that should support all hardware from Net.i82540. Attaching the
> latest Net.e1000 build.
>
> Respectfully,
> Oleg
>
> 22 марта 2016 г., в 13:09, edwin rinjani <community-noreply@qnx.com>
> написал:
>
> > hello,
> > sorry the driver i have found not Net.ether82540 but *Net.i82540, *
> > i hope som body can help me where can i download that driver…
> > thanks
> >
> > regards,
> > dodi s
> >
> > 2016-03-22 17:03 GMT+07:00 edwin rinjani <edwinrinjani@gmail.com>:
> >
> >> hello,
> >> i saw the qnx hardware support at :
> >>
> >>
> >>
> http://www.qnx.com/developers/hardware_support/qnx4/qnx4hardware.html?category=Network
> >>
> >> i need the driver for Intel RC 82540EM network adapter, at the following
> >> address i have found that the driver is Net.ether82540, but where can i
> >> download that driver, i hope some body can help me please...
> >>
> >> regards,
> >> dodi s
> >>
> >> 2016-03-18 20:44 GMT+07:00 Олег Большаков <community-noreply@qnx.com>:
> >>
> >>> Hello,
> >>>
> >>> Please specify the controller's name and PCI IDs (use show_pci -vv in
> >>> QNX4 console).
> >>>
> >>> Respectfully,
> >>> Oleg
> >>>
> >>> 18 марта 2016 г., в 9:32:57, edwin rinjani <community-noreply@qnx.com>
> >>> написал:
> >>>
> >>>> dear sir,
> >>>> I am an user of qnx 4.25 and we need driver for network card, we have
> >>> read the qnx 4 support network driver and i saw the status has
> released,
> >>> but i still confused where can i download the driver that has been
> released.
> >>>> can anybody give me a clue please.
> >>>> thank you
> >>>>
> >>>> regards,
> >>>> dodi s
> >>>
> >>>
> >>>
> >>>
> >>>
> >>> _______________________________________________
> >>>
> >>> QNX4 Community Support
> >>> http://community.qnx.com/sf/go/post115979
> >>> To cancel your subscription to this discussion, please e-mail
> >>> qnx4-community-unsubscribe@community.qnx.com
> >>>
> >>
> >>
> >
> >
> >
> >
> > _______________________________________________
> >
> > QNX4 Community Support
> > http://community.qnx.com/sf/go/post115992
> > To cancel your subscription to this discussion, please e-mail
> qnx4-community-unsubscribe@community.qnx.com
> > hello,
> > sorry the driver i have found not Net.ether82540 but Net.i82540,
> > i hope som body can help me where can i download that driver…
> > thanks
> >
> > regards,
> > dodi s
> >
> > 2016-03-22 17:03 GMT+07:00 edwin rinjani <edwinrinjani@gmail.com>:
> > hello,
> > i saw the qnx hardware support at :
> >
> >
> http://www.qnx.com/developers/hardware_support/qnx4/qnx4hardware.html?category=Network
> >
> > i need the driver for Intel RC 82540EM network adapter, at the following
> address i have found that the driver is Net.ether82540, but where can i
> download that driver, i hope some body can help me please...
> >
> > regards,
> > dodi s
> >
> > 2016-03-18 20:44 GMT+07:00 Олег Большаков <community-noreply@qnx.com>:
> > Hello,
> >
> > Please specify the controller's name and PCI IDs (use show_pci -vv in
> QNX4 console).
> >
> > Respectfully,
> > Oleg
> >
> > 18 марта 2016 г., в 9:32:57, edwin rinjani <community-noreply@qnx.com>
> написал:
> >
> > > dear sir,
> > > I am an user of qnx 4.25 and we need driver for network card, we have
> read the qnx 4 support network driver and i saw the status has released,
> but i still confused where can i download the driver that has been released.
> > > can anybody give me a clue please.
> > > thank you
> > >
> > > regards,
> > > dodi s
> >
> >
> >
> >
> >
> > _______________________________________________
> >
> > QNX4 Community Support
> > http://community.qnx.com/sf/go/post115979
> > To cancel your subscription to this discussion, please e-mail
> qnx4-community-unsubscribe@community.qnx.com
> >
> >
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post116012
> To cancel your subscription to this discussion, please e-mail
> qnx4-community-unsubscribe@community.qnx.com
>dodi sunardi2016-03-24T06:04:45Zpost116012: Re: None
http://community.qnx.com/sf/go/post116012
Hi Dodi,
You have to use Net.e1000 driver instead of Net.i82540. The Net.e1000 is a new driver that should support all hardware from Net.i82540. Attaching the latest Net.e1000 build.
Respectfully,
Oleg
22 марта 2016 г., в 13:09, edwin rinjani <community-noreply@qnx.com> написал:
> hello,
> sorry the driver i have found not Net.ether82540 but *Net.i82540, *
> i hope som body can help me where can i download that driver…
> thanks
>
> regards,
> dodi s
>
> 2016-03-22 17:03 GMT+07:00 edwin rinjani <edwinrinjani@gmail.com>:
>
>> hello,
>> i saw the qnx hardware support at :
>>
>>
>> http://www.qnx.com/developers/hardware_support/qnx4/qnx4hardware.html?category=Network
>>
>> i need the driver for Intel RC 82540EM network adapter, at the following
>> address i have found that the driver is Net.ether82540, but where can i
>> download that driver, i hope some body can help me please...
>>
>> regards,
>> dodi s
>>
>> 2016-03-18 20:44 GMT+07:00 Олег Большаков <community-noreply@qnx.com>:
>>
>>> Hello,
>>>
>>> Please specify the controller's name and PCI IDs (use show_pci -vv in
>>> QNX4 console).
>>>
>>> Respectfully,
>>> Oleg
>>>
>>> 18 марта 2016 г., в 9:32:57, edwin rinjani <community-noreply@qnx.com>
>>> написал:
>>>
>>>> dear sir,
>>>> I am an user of qnx 4.25 and we need driver for network card, we have
>>> read the qnx 4 support network driver and i saw the status has released,
>>> but i still confused where can i download the driver that has been released.
>>>> can anybody give me a clue please.
>>>> thank you
>>>>
>>>> regards,
>>>> dodi s
>>>
>>>
>>>
>>>
>>>
>>> _______________________________________________
>>>
>>> QNX4 Community Support
>>> http://community.qnx.com/sf/go/post115979
>>> To cancel your subscription to this discussion, please e-mail
>>> qnx4-community-unsubscribe@community.qnx.com
>>>
>>
>>
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post115992
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
> hello,
> sorry the driver i have found not Net.ether82540 but Net.i82540,
> i hope som body can help me where can i download that driver…
> thanks
>
> regards,
> dodi s
>
> 2016-03-22 17:03 GMT+07:00 edwin rinjani <edwinrinjani@gmail.com>:
> hello,
> i saw the qnx hardware support at :
>
> http://www.qnx.com/developers/hardware_support/qnx4/qnx4hardware.html?category=Network
>
> i need the driver for Intel RC 82540EM network adapter, at the following address i have found that the driver is Net.ether82540, but where can i download that driver, i hope some body can help me please...
>
> regards,
> dodi s
>
> 2016-03-18 20:44 GMT+07:00 Олег Большаков <community-noreply@qnx.com>:
> Hello,
>
> Please specify the controller's name and PCI IDs (use show_pci -vv in QNX4 console).
>
> Respectfully,
> Oleg
>
> 18 марта 2016 г., в 9:32:57, edwin rinjani <community-noreply@qnx.com> написал:
>
> > dear sir,
> > I am an user of qnx 4.25 and we need driver for network card, we have read the qnx 4 support network driver and i saw the status has released, but i still confused where can i download the driver that has been released.
> > can anybody give me a clue please.
> > thank you
> >
> > regards,
> > dodi s
>
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post115979
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
>
>Oleg Bolshakov2016-03-23T15:34:22Zpost116010: RE: RE: RE: RE: RE: Net.i82540....
http://community.qnx.com/sf/go/post116010
Hi Dodis,
I do not know which version of install CD you are using, but if you read back through this thread you'll see that Net.i82540 has been replaced by Net.e1000.. If you are using the 2011 CD or later then you should have the Net.e1000 driver already installed on your system. If not, you can get the latest Net.e1000 (or any other newer drivers that are available) from this page: http://community.qnx.com/sf/wiki/do/viewPage/projects.qnx4/wiki/LatestSoftwareUpdates which might be a good idea to get even if you do have the 2011 CD installed. Note: If you don't have 2011 CD installed and you just get the latest driver, you will not have updated versions of some network utilities ... the versions you have will not recognize this driver. I don't know the exact list , but remember reading about a utility that needed updating in this thread.
Also if you don't see the info you want when running a driver with "-v" add more v's... i.e. "-vvvv"... the more v's you add the more info you get (up to a point).
-Martin.
-----Original Message-----
From: dodi sunardi [mailto:community-noreply@qnx.com]
Sent: Wednesday, March 23, 2016 12:07 AM
To: qnx4-community <qnx4-community@community.qnx.com>
Subject: Re: RE: RE: RE: RE: Net.i82540....
hallo,
i have a network card with intel chipset 82540, than i found the driver Net.i82540, but that driver look like not working properly, because usually if i use command Net.i82540 -v & , its should be come out the list of hardware like mac address number and other, but in this case it is not coming out and i need the mac address to setting the network.
is any body have a problem solving for my problem.
thanks
dodi s
_______________________________________________
QNX4 Community Support
http://community.qnx.com/sf/go/post116007
To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comMartin Walter2016-03-23T14:54:49Zpost116007: Re: RE: RE: RE: RE: Net.i82540....
http://community.qnx.com/sf/go/post116007
hallo,
i have a network card with intel chipset 82540, than i found the driver Net.i82540, but that driver look like not working
properly, because usually if i use command Net.i82540 -v & , its should be come out the list of hardware like mac address number and other, but in this case it is not coming out and i need the mac address to setting the network.
is any body have a problem solving for my problem.
thanks
dodi sdodi sunardi2016-03-23T04:06:42Zpost115992: Re: None
http://community.qnx.com/sf/go/post115992
hello,
sorry the driver i have found not Net.ether82540 but *Net.i82540, *
i hope som body can help me where can i download that driver…
thanks
regards,
dodi s
2016-03-22 17:03 GMT+07:00 edwin rinjani <edwinrinjani@gmail.com>:
> hello,
> i saw the qnx hardware support at :
>
>
> http://www.qnx.com/developers/hardware_support/qnx4/qnx4hardware.html?category=Network
>
> i need the driver for Intel RC 82540EM network adapter, at the following
> address i have found that the driver is Net.ether82540, but where can i
> download that driver, i hope some body can help me please...
>
> regards,
> dodi s
>
> 2016-03-18 20:44 GMT+07:00 Олег Большаков <community-noreply@qnx.com>:
>
>> Hello,
>>
>> Please specify the controller's name and PCI IDs (use show_pci -vv in
>> QNX4 console).
>>
>> Respectfully,
>> Oleg
>>
>> 18 марта 2016 г., в 9:32:57, edwin rinjani <community-noreply@qnx.com>
>> написал:
>>
>> > dear sir,
>> > I am an user of qnx 4.25 and we need driver for network card, we have
>> read the qnx 4 support network driver and i saw the status has released,
>> but i still confused where can i download the driver that has been released.
>> > can anybody give me a clue please.
>> > thank you
>> >
>> > regards,
>> > dodi s
>>
>>
>>
>>
>>
>> _______________________________________________
>>
>> QNX4 Community Support
>> http://community.qnx.com/sf/go/post115979
>> To cancel your subscription to this discussion, please e-mail
>> qnx4-community-unsubscribe@community.qnx.com
>>
>
>dodi sunardi2016-03-22T10:09:48Zpost115990: Re: None
http://community.qnx.com/sf/go/post115990
hello,
i saw the qnx hardware support at :
http://www.qnx.com/developers/hardware_support/qnx4/qnx4hardware.html?category=Network
i need the driver for Intel RC 82540EM network adapter, at the following
address i have found that the driver is Net.ether82540, but where can i
download that driver, i hope some body can help me please...
regards,
dodi s
2016-03-18 20:44 GMT+07:00 Олег Большаков <community-noreply@qnx.com>:
> Hello,
>
> Please specify the controller's name and PCI IDs (use show_pci -vv in QNX4
> console).
>
> Respectfully,
> Oleg
>
> 18 марта 2016 г., в 9:32:57, edwin rinjani <community-noreply@qnx.com>
> написал:
>
> > dear sir,
> > I am an user of qnx 4.25 and we need driver for network card, we have
> read the qnx 4 support network driver and i saw the status has released,
> but i still confused where can i download the driver that has been released.
> > can anybody give me a clue please.
> > thank you
> >
> > regards,
> > dodi s
>
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post115979
> To cancel your subscription to this discussion, please e-mail
> qnx4-community-unsubscribe@community.qnx.com
>dodi sunardi2016-03-22T10:03:25Zpost115979: Re: None
http://community.qnx.com/sf/go/post115979
Hello,
Please specify the controller's name and PCI IDs (use show_pci -vv in QNX4 console).
Respectfully,
Oleg
18 марта 2016 г., в 9:32:57, edwin rinjani <community-noreply@qnx.com> написал:
> dear sir,
> I am an user of qnx 4.25 and we need driver for network card, we have read the qnx 4 support network driver and i saw the status has released, but i still confused where can i download the driver that has been released.
> can anybody give me a clue please.
> thank you
>
> regards,
> dodi sOleg Bolshakov2016-03-18T13:44:38Zpost115976: None
http://community.qnx.com/sf/go/post115976
dear sir,
I am an user of qnx 4.25 and we need driver for network card, we have read
the qnx 4 support network driver and i saw the status has released, but i
still confused where can i download the driver that has been released.
can anybody give me a clue please.
thank you
regards,
dodi sdodi sunardi2016-03-18T06:33:01Zpost115972: Re: QNX4 - penmount with USB does not work
http://community.qnx.com/sf/go/post115972
Hi Martin,
The Input supports Penmount controller via RS-232 only. There is no devu-xxx module.
Respectfully,
Oleg
15 марта 2016 г., в 17:42:08, Martin Köhler <community-noreply@qnx.com> написал:
> Hi Oleg and all,
>
> I happily found in the latest Input driver the Penmount protocol being included. Fantastic. But there is now devu-xxx what does anything with the penmount (USB vendor 0x14e1 id 0x6000, as far as I can see... all devu- never do even a verbose message. Really am desperating...
>
> devu-kbd works, though, what makes me believe the USB being finde (it's a EHCI, I tried with io-usb and io-usb-ehci).
>
> I'm running the last 2015 boot edition, so it might be the actual suite at all.
>
> any hints for me? thanks in advance!
>
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post115959
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2016-03-16T13:27:03Zpost115959: QNX4 - penmount with USB does not work
http://community.qnx.com/sf/go/post115959
Hi Oleg and all,
I happily found in the latest Input driver the Penmount protocol being included. Fantastic. But there is now devu-xxx what does anything with the penmount (USB vendor 0x14e1 id 0x6000, as far as I can see... all devu- never do even a verbose message. Really am desperating...
devu-kbd works, though, what makes me believe the USB being finde (it's a EHCI, I tried with io-usb and io-usb-ehci).
I'm running the last 2015 boot edition, so it might be the actual suite at all.
any hints for me? thanks in advance!Martin Köhler(deleted)2016-03-15T14:42:08Zpost115262: Re: Chinese language cannot correctly display in qnx4.25/pterm.
http://community.qnx.com/sf/go/post115262
Hi,
UTF-8 is not supported. You can use encoding from the list from "ptermcs".
You'll need chinese font for pcterm with .phf extension. Copy font in /qnx4/photon/font/, install it with "fontcfg" utility and restart photon.
Also you'll need a charsets file with .cs extension. You can create it with "ptermcs" utility.
Then select font in "Customize font list" of your pterm (Properties => Text Font => Customize), specify charsets file, select your font and add it to the list. Then select your font in pterm setting Text Font (Properties => Text Font).
Best regards,
FedorFedor Zharov(deleted)2015-12-10T14:15:20Zpost115228: Chinese language cannot correctly display in qnx4.25/pterm.
http://community.qnx.com/sf/go/post115228
Create the hello.c file and save it as UTF-8 format
Main void ()
{
While (1)
{
Printf ("中国人");
}
}
I put the file into UTF8 format ,Compile and run on the console display garbled, how to solve?,
thanks....wenwei wenwei(deleted)2015-12-05T11:43:27Zpost114814: Re: QNX4 system and C/C++ dev kit
http://community.qnx.com/sf/go/post114814
Got it. Thanks.
EvanEvan Han(deleted)2015-10-28T15:40:51Zpost114811: Re: QNX4 system and C/C++ dev kit
http://community.qnx.com/sf/go/post114811
Evan,
Yes, but as far as I know you can't purchase C++ compiler without C compiler. Can you contact your sales department? This is technical forum, so I may be wrong.
Отправлено с моего смартфона BlackBerry 10.
Исходное сообщение
От: Evan Han
Отправлено: среда, 28 октября 2015 г., 17:12
Кому: qnx4-community
Ответить: qnx4-community@community.qnx.com
Тема: Re: QNX4 system and C/C++ dev kit
Thanks Oleg. So if I understand correctly, QNX4 system, C compiler and C++ compiler are each sold separately, correct?
Thanks.
_______________________________________________
QNX4 Community Support
http://community.qnx.com/sf/go/post114807
To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2015-10-28T15:17:04Zpost114807: Re: QNX4 system and C/C++ dev kit
http://community.qnx.com/sf/go/post114807
Thanks Oleg. So if I understand correctly, QNX4 system, C compiler and C++ compiler are each sold separately, correct?
Thanks.Evan Han(deleted)2015-10-28T14:13:00Zpost114804: Re: QNX4 system and C/C++ dev kit
http://community.qnx.com/sf/go/post114804
Hi Evan,
Yes, C and C++ compilers come separately, but C++ compiler requires C compiler. You can’t use C++ without C.
Respectfully,
Oleg
28 окт. 2015 г., в 1:16, Evan Han <community-noreply@qnx.com> написал:
> Hi I am wondering if seperate purchases or licenses are needed for QNX4 system and C/C++ deve kit. Do C and C++ compilers come seperatly as well? Thanks.
>
> Evan
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post114798
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2015-10-28T04:53:20Zpost114798: QNX4 system and C/C++ dev kit
http://community.qnx.com/sf/go/post114798
Hi I am wondering if seperate purchases or licenses are needed for QNX4 system and C/C++ deve kit. Do C and C++ compilers come seperatly as well? Thanks.
EvanEvan Han(deleted)2015-10-27T22:16:17Zpost114639: Re: I211 support for QNX4
http://community.qnx.com/sf/go/post114639
can I get some update about this?wang long(deleted)2015-10-14T12:25:18Zpost114628: Re: How Windows client can print on QNX4 Samba server?
http://community.qnx.com/sf/go/post114628
Seems before network printer installation I have to login on Samba-server as root.
Thanks for support.Leonid Khait(deleted)2015-10-12T09:33:21Zpost114626: Re: How Windows client can print on QNX4 Samba server?
http://community.qnx.com/sf/go/post114626
If start smbd with DEBUG(3) level
#smbd -d3
it is printing/print_generic.c/print_run_command() additional output in log.smbd:
[2015/10/12 10:09:26, 3] printing/print_generic.c:print_run_command(88)
Running the command `/bin/echo "print smbprn.000003.030689 on ps" > /tmp/smbprint.log' gave 81
Return value 81 show the problem in lib/smbrun.c/smbrun():
/* now completely lose our privileges. This is a fairly paranoid
way of doing it, but it does work on all systems that I know of */
become_user_permanently(uid, gid);
if (getuid() != uid || geteuid() != uid ||
getgid() != gid || getegid() != gid) {
/* we failed to lose our privileges - do not execute
the command */
exit(81); /* we can't print stuff at this stage,
instead use exit codes for debugging */
}
Seems User ID uid и Group ID gid setup problem in become_user_permanently(uid, gid)
How to solve that? Thank you.
> Dear Oleg,
>
> With yours smb.conf configuration Windows 7 and Windows XP remoute network
> printer install and accept appropriate type of driver ( in Windows XP after
> addition rebooting ).
>
> >
> > [printers]
> > comment = Print Temporary Spool Configuration
> > path = /var/spool/samba
> > guest ok = Yes
> > printable = Yes
> > browseable = No
> >
> > [qnx_printer]
> > path = /tmp
> > guest ok = Yes
> > printable = Yes
> > postscript = Yes
> > print command = lp %s
> > printer name = 123
> > default devmode = Yes
> >
>
> On Windows side printing process looking as normal. In the printer spool
> print jobs appear,
> and then removed at the completion of printing.
>
> On QNX4 samba-server side when printing in /tmp folder trmporary files with
> names smbprn.*.* created and then removed.
>
> But described in smb.conf
>
> print command = lp% s
>
> not performed.
>
> It is also not carried out wit another option:
>
> print command = echo "print% s to% p" > /tmp/smbprint.log
>
> Although issued manually
>
> #lp filename
>
> works properly.
>
> How to make the samba-server to execute the command-line configuration of the
> "print command"?
>
> Thank you.
>
>
>
>
> >
> > 2. On Windows PC follow the next steps:
> >
> > Start->Printers and faxes->Add printer->next->a network printer ->choose
> > point ”Connect to a printer or to perform a review printers”->Select
> > your priter->set it Draiver-> try print the document.
> >
> > Let me know about your results.
> >
> > Respectfully,
> > Oleg
> >
> > 6 окт. 2015 г., в 6:53, Leonid Khait <community-noreply@qnx.com> написал:
> >
> > > Hi!
> > >
> > >> 1. How did you connect your printer to the QNX4 machine?
> > >
> > > The printer is connected to the parallel port of the PC with QNX4 and
> Samba-
> > server.
> > >
> > >
> > >
> > >> 2. How did you configure your printer in the QNX4 (lpd or spooler)?
> > >
> > > Printing output is configured by spooler.
> > >
> > >> 3. Does the printer print fine directly from the QNX4?
> > >
> > > Printout working fine directly from QNX4.
> > >
> > >> Also add output following commands from the QNX4 machine:
> > >
> > > The outputs with that command are attached.
> > >
> > > # sin arg
> > > # ls /dev
> > >
> > > Respectfully,
> > > Oleg
> > >
> > > 5 окт. 2015 г., в 5:37:41, Leonid Khait <community-noreply@qnx.com> написал:
> > >
> > >> I try to setup Windows XP Client printing on QNX4 Samba 2.2.12 server.
> > >>
> > >> Printer is connected to QNX4 PC.
> > >>
> > >> In the smb.conf new section is added:
> > >>
> > >> [qnx_printer]
> > >> printable=yes
> > >> path=/tmp
> > >> command=cp %s /dev/spool/ps; rm -rf %s
> > >> public=yes
> > >>
> > >> Windows file manager is opened with QNX4 IP address and printer Icon is
> > present in a Samba-server folder.
> > >>
> > >> But when I try to setup new network printer through Printer setup master,
>
> > error message is occure:
> > >>
> > >> "Unable to connect to the printer.
> > >> Wrong printer name or path. Printer lost connection to the server".
> > >>
> > >> How to solve the problem?
> > >> Thanks.
> > >>
> > >>
> > >
> > >
> > >
> > >
> > >
> > > _______________________________________________
> > >
> > > QNX4 Community Support
> > > http://community.qnx.com/sf/go/post114593
> > > To cancel your subscription to this discussion, please e-mail qnx4-
> community
> > -unsubscribe@community.qnx.com
> > > <ls_dev.txt><sin_arg.txt>
> >
>
>Leonid Khait(deleted)2015-10-12T06:40:44Zpost114624: Re: How Windows client can print on QNX4 Samba server?
http://community.qnx.com/sf/go/post114624
Dear Oleg,
With yours smb.conf configuration Windows 7 and Windows XP remoute network printer install and accept appropriate type of driver ( in Windows XP after addition rebooting ).
>
> [printers]
> comment = Print Temporary Spool Configuration
> path = /var/spool/samba
> guest ok = Yes
> printable = Yes
> browseable = No
>
> [qnx_printer]
> path = /tmp
> guest ok = Yes
> printable = Yes
> postscript = Yes
> print command = lp %s
> printer name = 123
> default devmode = Yes
>
On Windows side printing process looking as normal. In the printer spool print jobs appear,
and then removed at the completion of printing.
On QNX4 samba-server side when printing in /tmp folder trmporary files with names smbprn.*.* created and then removed.
But described in smb.conf
print command = lp% s
not performed.
It is also not carried out wit another option:
print command = echo "print% s to% p" > /tmp/smbprint.log
Although issued manually
#lp filename
works properly.
How to make the samba-server to execute the command-line configuration of the "print command"?
Thank you.
>
> 2. On Windows PC follow the next steps:
>
> Start->Printers and faxes->Add printer->next->a network printer ->choose
> point ”Connect to a printer or to perform a review printers”->Select
> your priter->set it Draiver-> try print the document.
>
> Let me know about your results.
>
> Respectfully,
> Oleg
>
> 6 окт. 2015 г., в 6:53, Leonid Khait <community-noreply@qnx.com> написал:
>
> > Hi!
> >
> >> 1. How did you connect your printer to the QNX4 machine?
> >
> > The printer is connected to the parallel port of the PC with QNX4 and Samba-
> server.
> >
> >
> >
> >> 2. How did you configure your printer in the QNX4 (lpd or spooler)?
> >
> > Printing output is configured by spooler.
> >
> >> 3. Does the printer print fine directly from the QNX4?
> >
> > Printout working fine directly from QNX4.
> >
> >> Also add output following commands from the QNX4 machine:
> >
> > The outputs with that command are attached.
> >
> > # sin arg
> > # ls /dev
> >
> > Respectfully,
> > Oleg
> >
> > 5 окт. 2015 г., в 5:37:41, Leonid Khait <community-noreply@qnx.com> написал:
> >
> >> I try to setup Windows XP Client printing on QNX4 Samba 2.2.12 server.
> >>
> >> Printer is connected to QNX4 PC.
> >>
> >> In the smb.conf new section is added:
> >>
> >> [qnx_printer]
> >> printable=yes
> >> path=/tmp
> >> command=cp %s /dev/spool/ps; rm -rf %s
> >> public=yes
> >>
> >> Windows file manager is opened with QNX4 IP address and printer Icon is
> present in a Samba-server folder.
> >>
> >> But when I try to setup new network printer through Printer setup master,
> error message is occure:
> >>
> >> "Unable to connect to the printer.
> >> Wrong printer name or path. Printer lost connection to the server".
> >>
> >> How to solve the problem?
> >> Thanks.
> >>
> >>
> >
> >
> >
> >
> >
> > _______________________________________________
> >
> > QNX4 Community Support
> > http://community.qnx.com/sf/go/post114593
> > To cancel your subscription to this discussion, please e-mail qnx4-community
> -unsubscribe@community.qnx.com
> > <ls_dev.txt><sin_arg.txt>
>Leonid Khait(deleted)2015-10-11T06:38:36Zpost114622: Re: I211 support for QNX4
http://community.qnx.com/sf/go/post114622
more details found with -vvv (curious, I can't use console redirection to save all the log to files, but other app can, so I have to type the last screen to you, any suggestion?)
e1000_check_alt_mac_addr_generic
e1000_read_invm_i210
NVM word 0x03 is not mapped
e1000_read_mac_addr_82575
e1000_check_alt_mac_addr_generic
e1000_read_invm_i210
NVM word 0x03 is not mapped
e1000_reset_hw_82580
e1000_disable_pcie_master_generic
Masking off all interrupts
e1000_ge_auto_rd_done_generic
e1000_reset_mdicnfg_82580
e1000_check_alt_mac_addr_generic
e1000_read_invm_i210
NVM word 0x03 is not mapped
e1000_init_hw_i210
e1000_get_flash_presence_i210
e1000_read_invm_word_i210
//1/bin/Net terminated (SIGSEGV) at 0015:000003D8.wang long(deleted)2015-10-10T07:01:08Zpost114620: Re: I211 support for QNX4
http://community.qnx.com/sf/go/post114620
Upload the picture of the failure.
> It reported the same error as previous revision:
> the last line indicted this caused the memory fault of Net
>
> %1 80 Memory fault Net -d6
>
> any other hidden options can expose more debug information?
>
> > Please try the attached driver and let me know if it works.
> >
> > Thanks, Hugh.
> >
> >
> >
> > On 2015/10/8, 6:05 PM, "wang long" <community-noreply@qnx.com> wrote:
> >
> > >All the I211 ports are located on a single customized motherboard, I
> > >think they are just like the
> > >prototype provided by intel.
> > >the functionalities of the ports have been validated under Windows7 and
> > >Linux.
> > >
> > >please let me know if you want anything in detail.
> > >
> > >> Are the I211 adapters on PCIe boards? If so, could you please give me
> > >>the
> > >> Intel name of the adapter?
> > >> a
> > >> Thanks, Hugh.
> > >>
> > >>
> > >>
> > >>
> > >> On 2015/10/8, 8:45 AM, "wang long" <community-noreply@qnx.com> wrote:
> > >>
> > >> >I have 6 I211 ports, but only one of them is connected to a 100M
> > >>network,
> > >> >I tried for each port, they all got same output.
> > >> >
> > >> >the Net was got from the QNX 4 Product Suite CD 2015 EXPERIMENTAL,
> > >> >and the Net.e1000 is the attched driver. I'm not clear if they are
> > >> >matched.
> > >> >
> > >> >> I¹ll have to take a look at this when I get a chance. Are you
> > >>connecting
> > >> >> to a 10Mb network?
> > >> >>
> > >> >>
> > >> >
> > >> >
> > >> >
> > >> >
> > >> >
> > >> >
> > >> >_______________________________________________
> > >> >
> > >> >QNX4 Community Support
> > >> >http://community.qnx.com/sf/go/post114608
> > >> >To cancel your subscription to this discussion, please e-mail
> > >> >qnx4-community-unsubscribe@community.qnx.com
> > >>
> > >
> > >
> > >
> > >
> > >
> > >
> > >_______________________________________________
> > >
> > >QNX4 Community Support
> > >http://community.qnx.com/sf/go/post114613
> > >To cancel your subscription to this discussion, please e-mail
> > >qnx4-community-unsubscribe@community.qnx.com
> >
>
>wang long(deleted)2015-10-10T05:36:44Zpost114619: Re: I211 support for QNX4
http://community.qnx.com/sf/go/post114619
It reported the same error as previous revision:
the last line indicted this caused the memory fault of Net
%1 80 Memory fault Net -d6
any other hidden options can expose more debug information?
> Please try the attached driver and let me know if it works.
>
> Thanks, Hugh.
>
>
>
> On 2015/10/8, 6:05 PM, "wang long" <community-noreply@qnx.com> wrote:
>
> >All the I211 ports are located on a single customized motherboard, I
> >think they are just like the
> >prototype provided by intel.
> >the functionalities of the ports have been validated under Windows7 and
> >Linux.
> >
> >please let me know if you want anything in detail.
> >
> >> Are the I211 adapters on PCIe boards? If so, could you please give me
> >>the
> >> Intel name of the adapter?
> >> a
> >> Thanks, Hugh.
> >>
> >>
> >>
> >>
> >> On 2015/10/8, 8:45 AM, "wang long" <community-noreply@qnx.com> wrote:
> >>
> >> >I have 6 I211 ports, but only one of them is connected to a 100M
> >>network,
> >> >I tried for each port, they all got same output.
> >> >
> >> >the Net was got from the QNX 4 Product Suite CD 2015 EXPERIMENTAL,
> >> >and the Net.e1000 is the attched driver. I'm not clear if they are
> >> >matched.
> >> >
> >> >> I¹ll have to take a look at this when I get a chance. Are you
> >>connecting
> >> >> to a 10Mb network?
> >> >>
> >> >>
> >> >
> >> >
> >> >
> >> >
> >> >
> >> >
> >> >_______________________________________________
> >> >
> >> >QNX4 Community Support
> >> >http://community.qnx.com/sf/go/post114608
> >> >To cancel your subscription to this discussion, please e-mail
> >> >qnx4-community-unsubscribe@community.qnx.com
> >>
> >
> >
> >
> >
> >
> >
> >_______________________________________________
> >
> >QNX4 Community Support
> >http://community.qnx.com/sf/go/post114613
> >To cancel your subscription to this discussion, please e-mail
> >qnx4-community-unsubscribe@community.qnx.com
>wang long(deleted)2015-10-10T02:44:08Zpost114618: Re: I211 support for QNX4
http://community.qnx.com/sf/go/post114618
Please try the attached driver and let me know if it works.
Thanks, Hugh.
On 2015/10/8, 6:05 PM, "wang long" <community-noreply@qnx.com> wrote:
>All the I211 ports are located on a single customized motherboard, I
>think they are just like the
>prototype provided by intel.
>the functionalities of the ports have been validated under Windows7 and
>Linux.
>
>please let me know if you want anything in detail.
>
>> Are the I211 adapters on PCIe boards? If so, could you please give me
>>the
>> Intel name of the adapter?
>> a
>> Thanks, Hugh.
>>
>>
>>
>>
>> On 2015/10/8, 8:45 AM, "wang long" <community-noreply@qnx.com> wrote:
>>
>> >I have 6 I211 ports, but only one of them is connected to a 100M
>>network,
>> >I tried for each port, they all got same output.
>> >
>> >the Net was got from the QNX 4 Product Suite CD 2015 EXPERIMENTAL,
>> >and the Net.e1000 is the attched driver. I'm not clear if they are
>> >matched.
>> >
>> >> I¹ll have to take a look at this when I get a chance. Are you
>>connecting
>> >> to a 10Mb network?
>> >>
>> >>
>> >
>> >
>> >
>> >
>> >
>> >
>> >_______________________________________________
>> >
>> >QNX4 Community Support
>> >http://community.qnx.com/sf/go/post114608
>> >To cancel your subscription to this discussion, please e-mail
>> >qnx4-community-unsubscribe@community.qnx.com
>>
>
>
>
>
>
>
>_______________________________________________
>
>QNX4 Community Support
>http://community.qnx.com/sf/go/post114613
>To cancel your subscription to this discussion, please e-mail
>qnx4-community-unsubscribe@community.qnx.comHugh Brown2015-10-09T18:00:57Zpost114613: Re: I211 support for QNX4
http://community.qnx.com/sf/go/post114613
All the I211 ports are located on a single customized motherboard, I think they are just like the
prototype provided by intel.
the functionalities of the ports have been validated under Windows7 and Linux.
please let me know if you want anything in detail.
> Are the I211 adapters on PCIe boards? If so, could you please give me the
> Intel name of the adapter?
> a
> Thanks, Hugh.
>
>
>
>
> On 2015/10/8, 8:45 AM, "wang long" <community-noreply@qnx.com> wrote:
>
> >I have 6 I211 ports, but only one of them is connected to a 100M network,
> >I tried for each port, they all got same output.
> >
> >the Net was got from the QNX 4 Product Suite CD 2015 EXPERIMENTAL,
> >and the Net.e1000 is the attched driver. I'm not clear if they are
> >matched.
> >
> >> I¹ll have to take a look at this when I get a chance. Are you connecting
> >> to a 10Mb network?
> >>
> >>
> >
> >
> >
> >
> >
> >
> >_______________________________________________
> >
> >QNX4 Community Support
> >http://community.qnx.com/sf/go/post114608
> >To cancel your subscription to this discussion, please e-mail
> >qnx4-community-unsubscribe@community.qnx.com
>wang long(deleted)2015-10-08T22:05:21Zpost114612: Re: How Windows client can print on QNX4 Samba server?
http://community.qnx.com/sf/go/post114612
Hi Leonid,
1. Launch smbd on QNX4 PC using the following smb.conf file:
[printers]
comment = Print Temporary Spool Configuration
path = /var/spool/samba
guest ok = Yes
printable = Yes
browseable = No
[qnx_printer]
path = /tmp
guest ok = Yes
printable = Yes
postscript = Yes
print command = lp %s
printer name = 123
default devmode = Yes
2. On Windows PC follow the next steps:
Start->Printers and faxes->Add printer->next->a network printer ->choose
point ”Connect to a printer or to perform a review printers”->Select
your priter->set it Draiver-> try print the document.
Let me know about your results.
Respectfully,
Oleg
6 окт. 2015 г., в 6:53, Leonid Khait <community-noreply@qnx.com> написал:
> Hi!
>
>> 1. How did you connect your printer to the QNX4 machine?
>
> The printer is connected to the parallel port of the PC with QNX4 and Samba-server.
>
>
>
>> 2. How did you configure your printer in the QNX4 (lpd or spooler)?
>
> Printing output is configured by spooler.
>
>> 3. Does the printer print fine directly from the QNX4?
>
> Printout working fine directly from QNX4.
>
>> Also add output following commands from the QNX4 machine:
>
> The outputs with that command are attached.
>
> # sin arg
> # ls /dev
>
> Respectfully,
> Oleg
>
> 5 окт. 2015 г., в 5:37:41, Leonid Khait <community-noreply@qnx.com> написал:
>
>> I try to setup Windows XP Client printing on QNX4 Samba 2.2.12 server.
>>
>> Printer is connected to QNX4 PC.
>>
>> In the smb.conf new section is added:
>>
>> [qnx_printer]
>> printable=yes
>> path=/tmp
>> command=cp %s /dev/spool/ps; rm -rf %s
>> public=yes
>>
>> Windows file manager is opened with QNX4 IP address and printer Icon is present in a Samba-server folder.
>>
>> But when I try to setup new network printer through Printer setup master, error message is occure:
>>
>> "Unable to connect to the printer.
>> Wrong printer name or path. Printer lost connection to the server".
>>
>> How to solve the problem?
>> Thanks.
>>
>>
>
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post114593
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
> <ls_dev.txt><sin_arg.txt>Oleg Bolshakov2015-10-08T17:52:22Zpost114610: Re: I211 support for QNX4
http://community.qnx.com/sf/go/post114610
Are the I211 adapters on PCIe boards? If so, could you please give me the
Intel name of the adapter?
Thanks, Hugh.
On 2015/10/8, 8:45 AM, "wang long" <community-noreply@qnx.com> wrote:
>I have 6 I211 ports, but only one of them is connected to a 100M network,
>I tried for each port, they all got same output.
>
>the Net was got from the QNX 4 Product Suite CD 2015 EXPERIMENTAL,
>and the Net.e1000 is the attched driver. I'm not clear if they are
>matched.
>
>> I¹ll have to take a look at this when I get a chance. Are you connecting
>> to a 10Mb network?
>>
>>
>
>
>
>
>
>
>_______________________________________________
>
>QNX4 Community Support
>http://community.qnx.com/sf/go/post114608
>To cancel your subscription to this discussion, please e-mail
>qnx4-community-unsubscribe@community.qnx.comHugh Brown2015-10-08T14:55:14Zpost114608: Re: I211 support for QNX4
http://community.qnx.com/sf/go/post114608
I have 6 I211 ports, but only one of them is connected to a 100M network,
I tried for each port, they all got same output.
the Net was got from the QNX 4 Product Suite CD 2015 EXPERIMENTAL,
and the Net.e1000 is the attched driver. I'm not clear if they are matched.
> I¹ll have to take a look at this when I get a chance. Are you connecting
> to a 10Mb network?
>
>wang long(deleted)2015-10-08T12:45:22Zpost114607: Re: I211 support for QNX4
http://community.qnx.com/sf/go/post114607
I¹ll have to take a look at this when I get a chance. Are you connecting
to a 10Mb network?
On 2015/10/8, 6:40 AM, "wang long" <community-noreply@qnx.com> wrote:
>Thanks, but I still got the errors, should I get a new version for
>/bin/Net?
>
>Cmd:
>Net.e1000 -v -l1-I0
>
>Device 1539 - Revision 3
>After fix-ups FlowControl is now = 0
>Forcing Speed and Duplex
>
>M88E1000 PSCR: 0x3150
>Full Duplex
>
>Forcing 10mb
>
>Unable to establish link!!!
>
>Initializing the Flow Control address, type and timer regs
>
>Masking off all interrupts
>
>NVM work 0x03 is not mapped.
>NVM word 0x03 is not mapped.
>Masking off all interrupts
>
>NVM word 0x03 is not mapped.
>
>//1/bin/Net terminated (SIGSEGV) at 0015:000003D8
>Net.e1000: INITIALIZATION ERROR 3
>net_reg failed.
>
>
>
>_______________________________________________
>
>QNX4 Community Support
>http://community.qnx.com/sf/go/post114606
>To cancel your subscription to this discussion, please e-mail
>qnx4-community-unsubscribe@community.qnx.comHugh Brown2015-10-08T12:39:14Zpost114606: Re: I211 support for QNX4
http://community.qnx.com/sf/go/post114606
Thanks, but I still got the errors, should I get a new version for /bin/Net?
Cmd:
Net.e1000 -v -l1-I0
Device 1539 - Revision 3
After fix-ups FlowControl is now = 0
Forcing Speed and Duplex
M88E1000 PSCR: 0x3150
Full Duplex
Forcing 10mb
Unable to establish link!!!
Initializing the Flow Control address, type and timer regs
Masking off all interrupts
NVM work 0x03 is not mapped.
NVM word 0x03 is not mapped.
Masking off all interrupts
NVM word 0x03 is not mapped.
//1/bin/Net terminated (SIGSEGV) at 0015:000003D8
Net.e1000: INITIALIZATION ERROR 3
net_reg failed.wang long(deleted)2015-10-08T10:40:20Zpost114603: Re: I211 support for QNX4
http://community.qnx.com/sf/go/post114603
Please try the attached driver. You don¹t need to pass the device ID on
the command line.
On 2015/10/7, 10:06 AM, "wang long" <community-noreply@qnx.com> wrote:
>is I211 supported on QNX4 via Net.e1000?
>
>I got Net.e1000: INITIALIZATION ERROR 1 when I used the following command:
>
>Net.e1000 -v -d1539 -l1-I0
>
>Device 1539 - Revision 3
>Net.e1000: INITIALIZATION ERROR 1
>net_reg failed.
>
>
>
>
>_______________________________________________
>
>QNX4 Community Support
>http://community.qnx.com/sf/go/post114602
>To cancel your subscription to this discussion, please e-mail
>qnx4-community-unsubscribe@community.qnx.comHugh Brown2015-10-07T15:06:33Zpost114602: I211 support for QNX4
http://community.qnx.com/sf/go/post114602
is I211 supported on QNX4 via Net.e1000?
I got Net.e1000: INITIALIZATION ERROR 1 when I used the following command:
Net.e1000 -v -d1539 -l1-I0
Device 1539 - Revision 3
Net.e1000: INITIALIZATION ERROR 1
net_reg failed.wang long(deleted)2015-10-07T14:06:33Zpost114600: Re: help about the latest Dev32.ansi
http://community.qnx.com/sf/go/post114600
cool, it works.
Thanks a lot.wang long(deleted)2015-10-07T12:23:42Zpost114599: Re: help about the latest Dev32.ansi
http://community.qnx.com/sf/go/post114599
Hi Wang,
You have to launch following commands to use USB keyboard in console:
io-usb
devu-kbd
Dev
Dev.ansi -Q -n6 -d /dev/usbkbd0 &
Отправлено с моего смартфона BlackBerry 10.
Исходное сообщение
От: wang long
Отправлено: среда, 7 октября 2015 г., 13:40
Кому: qnx4-community
Ответить: qnx4-community@community.qnx.com
Тема: help about the latest Dev32.ansi
Just noticed that in the "QNX® 4 Product Suite 2015 Experimental Release Notes"
Dev32.ansi
Added support of USB keyboards in console
any comments on how to use this to support USB keyboard?
_______________________________________________
QNX4 Community Support
http://community.qnx.com/sf/go/post114598
To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2015-10-07T10:52:29Zpost114598: help about the latest Dev32.ansi
http://community.qnx.com/sf/go/post114598
Just noticed that in the "QNX® 4 Product Suite 2015 Experimental Release Notes"
Dev32.ansi
Added support of USB keyboards in console
any comments on how to use this to support USB keyboard?wang long(deleted)2015-10-07T10:40:45Zpost114593: Re: How Windows client can print on QNX4 Samba server?
http://community.qnx.com/sf/go/post114593
Hi!
>1. How did you connect your printer to the QNX4 machine?
The printer is connected to the parallel port of the PC with QNX4 and Samba-server.
>2. How did you configure your printer in the QNX4 (lpd or spooler)?
Printing output is configured by spooler.
>3. Does the printer print fine directly from the QNX4?
Printout working fine directly from QNX4.
>Also add output following commands from the QNX4 machine:
The outputs with that command are attached.
# sin arg
# ls /dev
Respectfully,
Oleg
5 окт. 2015 г., в 5:37:41, Leonid Khait <community-noreply@qnx.com> написал:
> I try to setup Windows XP Client printing on QNX4 Samba 2.2.12 server.
>
> Printer is connected to QNX4 PC.
>
> In the smb.conf new section is added:
>
> [qnx_printer]
> printable=yes
> path=/tmp
> command=cp %s /dev/spool/ps; rm -rf %s
> public=yes
>
> Windows file manager is opened with QNX4 IP address and printer Icon is present in a Samba-server folder.
>
> But when I try to setup new network printer through Printer setup master, error message is occure:
>
> "Unable to connect to the printer.
> Wrong printer name or path. Printer lost connection to the server".
>
> How to solve the problem?
> Thanks.
>
>Leonid Khait(deleted)2015-10-06T03:53:04Zpost114590: Re: How Windows client can print on QNX4 Samba server?
http://community.qnx.com/sf/go/post114590
Hi Leonid,
Please post here additional data:
1. How did you connect your printer to the QNX4 machine?
2. How did you configure your printer in the QNX4 (lpd or spooler)?
3. Does the printer print fine directly from the QNX4?
Also add output following commands from the QNX4 machine:
# sin arg
# ls /dev
Respectfully,
Oleg
5 окт. 2015 г., в 5:37:41, Leonid Khait <community-noreply@qnx.com> написал:
> I try to setup Windows XP Client printing on QNX4 Samba 2.2.12 server.
>
> Printer is connected to QNX4 PC.
>
> In the smb.conf new section is added:
>
> [qnx_printer]
> printable=yes
> path=/tmp
> command=cp %s /dev/spool/ps; rm -rf %s
> public=yes
>
> Windows file manager is opened with QNX4 IP address and printer Icon is present in a Samba-server folder.
>
> But when I try to setup new network printer through Printer setup master, error message is occure:
>
> "Unable to connect to the printer.
> Wrong printer name or path. Printer lost connection to the server".
>
> How to solve the problem?
> Thanks.
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post114586
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2015-10-05T18:37:01Zpost114586: How Windows client can print on QNX4 Samba server?
http://community.qnx.com/sf/go/post114586
I try to setup Windows XP Client printing on QNX4 Samba 2.2.12 server.
Printer is connected to QNX4 PC.
In the smb.conf new section is added:
[qnx_printer]
printable=yes
path=/tmp
command=cp %s /dev/spool/ps; rm -rf %s
public=yes
Windows file manager is opened with QNX4 IP address and printer Icon is present in a Samba-server folder.
But when I try to setup new network printer through Printer setup master, error message is occure:
"Unable to connect to the printer.
Wrong printer name or path. Printer lost connection to the server".
How to solve the problem?
Thanks.Leonid Khait(deleted)2015-10-05T02:37:41Zpost114482: Re: QNX 4.25 hard disk image
http://community.qnx.com/sf/go/post114482
Thanks Oleg for your answer.
Actually I'm in vacation so I can't give you precise details. We are having problems with a manufacturing semiconductor equipment (resist removal) which has as the main computer a QNX 4.25 OS. Because this Novellus equipment is quite old, we suspect that the hard disk or the application installed are not functioning properly any more. We have random SECS disconnections. So before doing anything, we planned to do at least an hard disk image. My colleague called me home to have some help but nobody of us in fact knows this OS. I found on the web that Ghost supports this kind of file system and can be used to do images . As soon as I finish my vacation, I'll let you know how this issue is evolving.
I thanks you again for your time and answer.Michele Faccini(deleted)2015-09-19T06:11:42Zpost114477: Re: QNX 4.25 hard disk image
http://community.qnx.com/sf/go/post114477
Hi Michele,
What do you do with disk image? Which troubles do you experience using dd command? Did you set IDE controller to LBA or CHS mode?
Respectfully,
Oleg
18 сент. 2015 г., в 16:39, Michele Faccini <community-noreply@qnx.com> написал:
> Hi all,
> I need to do an image of an ide hard disk on which QNX 4.25 is installed. We already tried with Linux dd command but with no chance. Can please somebody point me in the right direction !
> Any answer/help would be really appreciated....Thanks in advance
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post114473
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2015-09-18T20:05:48Zpost114473: QNX 4.25 hard disk image
http://community.qnx.com/sf/go/post114473
Hi all,
I need to do an image of an ide hard disk on which QNX 4.25 is installed. We already tried with Linux dd command but with no chance. Can please somebody point me in the right direction !
Any answer/help would be really appreciated....Thanks in advanceMichele Faccini(deleted)2015-09-18T13:39:03Zpost114356: Re: Support for Intel Graphics for the GENE-CV05
http://community.qnx.com/sf/go/post114356
Hi Andy,
PowerVR controllers are supported by QNX4 by VESA/VGA drivers only. It's prefered to try Hydra.ms/Pg.flat drivers. If you experience problem while installing QNX4 then just skip probing video in Installation program. You can detect graphics hw later. Did you install the QNX 4? What do you do to configure graphics? What is your result?
Respectfully,
Oleg
27 авг. 2015 г., в 4:32:13, Andy Rhind <community-noreply@qnx.com> написал:
> Hi:
>
> I'm trying to get a Aaeon GENE-CV05 board to run QNX4. So far everything appears to be running well, I just cant get the Graphics to run either in VESA, VGA or native.
>
> I started with the 2010 release and now I'm currently using the 2015 experimental update .
>
> Has anyone successfully go this card or graphics chipset to work (vid/did = 8086:be2)
>
> Thanks,
> Andy
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post114355
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2015-08-27T12:12:57Zpost114355: Support for Intel Graphics for the GENE-CV05
http://community.qnx.com/sf/go/post114355
Hi:
I'm trying to get a Aaeon GENE-CV05 board to run QNX4. So far everything appears to be running well, I just cant get the Graphics to run either in VESA, VGA or native.
I started with the 2010 release and now I'm currently using the 2015 experimental update .
Has anyone successfully go this card or graphics chipset to work (vid/did = 8086:be2)
Thanks,
AndyAndy Rhind2015-08-27T01:32:13Zpost114013: Re: First element data corruption in a vector
http://community.qnx.com/sf/go/post114013
Hi Ong,
This is QNX 4 discussion board, but you asked about QNX 6.6. Please post your question in right forum. It’d be great to add a full minimal example (including main() and Makefile) to illustrate the issue.
Respectfully,
Oleg
24 июня 2015 г., в 5:41:32, Ong Di Yong <community-noreply@qnx.com> написал:
> Hi all, I noticed that whenever I push_pack() a structure into a vector, there will be incidents when the content in the first element always get corrupted. This does not happen consistently but rather randomly.
>
> my structure is defined as follows:
> struct myStruct
> {
> uint32_t content1;
> uint32_t content2;
> uint32_t content3;
> uint32_t content4;
> }
>
> Usage is as follows:
> class myClass
> {
> public:
> void Update();
> void Retrieve(std::vector<myStruct> &list);
> private:
> std::vector<myStruct> m_list;
> }
> void myClass::Update()
> {
> myStruct temp;
>
> // performing operations to fill up contents in myStruct
>
> m_list.push_back(temp);
> }
>
> void myClass::Retrieve( std::vector<myStruct> &list)
> {
> for(uint32_t i=0; i<m_list.size(); i++)
> std::cout << m_list[i].content1 << std::endl;
> list = m_list;
> }
>
> I noticed that when I called Retrieve(), the content1 is changed randomly although I have verified that the contents inside are per what was pushed in in Update(). I am currently using QNX 6.6.0.
>
> May I know what is causing this problem? Thanks.
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post114010
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2015-06-24T08:44:41Zpost114010: First element data corruption in a vector
http://community.qnx.com/sf/go/post114010
Hi all, I noticed that whenever I push_pack() a structure into a vector, there will be incidents when the content in the first element always get corrupted. This does not happen consistently but rather randomly.
my structure is defined as follows:
struct myStruct
{
uint32_t content1;
uint32_t content2;
uint32_t content3;
uint32_t content4;
}
Usage is as follows:
class myClass
{
public:
void Update();
void Retrieve(std::vector<myStruct> &list);
private:
std::vector<myStruct> m_list;
}
void myClass::Update()
{
myStruct temp;
// performing operations to fill up contents in myStruct
m_list.push_back(temp);
}
void myClass::Retrieve( std::vector<myStruct> &list)
{
for(uint32_t i=0; i<m_list.size(); i++)
std::cout << m_list[i].content1 << std::endl;
list = m_list;
}
I noticed that when I called Retrieve(), the content1 is changed randomly although I have verified that the contents inside are per what was pushed in in Update(). I am currently using QNX 6.6.0.
May I know what is causing this problem? Thanks.Ong Di Yong(deleted)2015-06-24T02:41:32Zpost113926: 回复: The use of LPD QNX4 under way, why can't print Russian? (print HP2055dn).
http://community.qnx.com/sf/go/post113926
Oleg:
Under your help,The problem has been solved.!thank you very much@_@
Glad to meet you.
I wish you a successful job
wenwei.
------------------ 原始邮件 ------------------
发件人: "Олег Большаков";<community-noreply@qnx.com>;
发送时间: 2015年6月4日(星期四) 晚上6:00
收件人: "qnx4-community"<qnx4-community@community.qnx.com>;
主题: Re: The use of LPD QNX4 under way, why can't print Russian? (print HP2055dn).
Hello!
Please attach a screenshot with your settings of symbol set and a text file that you print.
Respectfully,
Oleg
3 июня 2015 г., в 11:29:38, 眼镜 <community-noreply@qnx.com> написал:
> Oleg:
>
>
> Thank you for your help.! Today I according to your method test, print newline incorrect has been resolved. But still
> cannot print Russian, accessory is the test file, hope you can help me to test you, dear bitter.
>
>
>
>
> wenwei!
>
>
_______________________________________________
QNX4 Community Support
http://community.qnx.com/sf/go/post113922
To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comwenwei wenwei(deleted)2015-06-05T09:41:54Zpost113922: Re: The use of LPD QNX4 under way, why can't print Russian? (print HP2055dn).
http://community.qnx.com/sf/go/post113922
Hello!
Please attach a screenshot with your settings of symbol set and a text file that you print.
Respectfully,
Oleg
3 июня 2015 г., в 11:29:38, 眼镜 <community-noreply@qnx.com> написал:
> Oleg:
>
>
> Thank you for your help.! Today I according to your method test, print newline incorrect has been resolved. But still
> cannot print Russian, accessory is the test file, hope you can help me to test you, dear bitter.
>
>
>
>
> wenwei!
>
>Oleg Bolshakov2015-06-04T10:00:38Zpost113916: 回复: The use of LPD QNX4 under way, why can't print Russian? (print HP2055dn).
http://community.qnx.com/sf/go/post113916
Oleg:
Thank you for your help.! Today I according to your method test, print newline incorrect has been resolved. But still cannot print Russian, accessory is the test file, hope you can help me to test you, dear bitter.
wenwei!
------------------ 原始邮件 ------------------
发件人: "Олег Большаков";<community-noreply@qnx.com>;
发送时间: 2015年6月2日(星期二) 晚上10:46
收件人: "qnx4-community@community.qnx.com"<qnx4-community@community.qnx.com>;
主题: Re: The use of LPD QNX4 under way, why can't print Russian? (print HP2055dn).
Hello,
I’ve configured my printer via web interface. You can use Windows to setup printer. After this you can print under QNX.
Respectfully,
Oleg
2 июня 2015 г., в 17:20:24, wenwei wenwei <community-noreply@qnx.com> написал:
> Thank you very much for your help. May I help you? In addition, your picture is Windows printer driver software? How can I set up this option under QNX4?
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post113907
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
_______________________________________________
QNX4 Community Support
http://community.qnx.com/sf/go/post113909
To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comwenwei wenwei(deleted)2015-06-03T08:40:43Zpost113910: 回复: The use of LPD QNX4 under way, why can't print Russian? (print HP2055dn).
http://community.qnx.com/sf/go/post113910
Thank you very much. I think your method should be right. I'll go to the company to test tomorrow..
------------------ 原始邮件 ------------------
发件人: "Олег Большаков";<community-noreply@qnx.com>;
发送时间: 2015年6月2日(星期二) 晚上10:46
收件人: "qnx4-community@community.qnx.com"<qnx4-community@community.qnx.com>;
主题: Re: The use of LPD QNX4 under way, why can't print Russian? (print HP2055dn).
Hello,
I’ve configured my printer via web interface. You can use Windows to setup printer. After this you can print under QNX.
Respectfully,
Oleg
2 июня 2015 г., в 17:20:24, wenwei wenwei <community-noreply@qnx.com> написал:
> Thank you very much for your help. May I help you? In addition, your picture is Windows printer driver software? How can I set up this option under QNX4?
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post113907
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
_______________________________________________
QNX4 Community Support
http://community.qnx.com/sf/go/post113909
To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comwenwei wenwei(deleted)2015-06-02T14:49:33Zpost113909: Re: The use of LPD QNX4 under way, why can't print Russian? (print HP2055dn).
http://community.qnx.com/sf/go/post113909
Hello,
I’ve configured my printer via web interface. You can use Windows to setup printer. After this you can print under QNX.
Respectfully,
Oleg
2 июня 2015 г., в 17:20:24, wenwei wenwei <community-noreply@qnx.com> написал:
> Thank you very much for your help. May I help you? In addition, your picture is Windows printer driver software? How can I set up this option under QNX4?
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post113907
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2015-06-02T14:46:43Zpost113907: Re: 回复: The use of LPD QNX4 under way, why can't print Russian? (print HP2055dn).
http://community.qnx.com/sf/go/post113907
Thank you very much for your help. May I help you? In addition, your picture is Windows printer driver software? How can I set up this option under QNX4?wenwei wenwei(deleted)2015-06-02T14:20:24Zpost113906: Re: 回复: The use of LPD QNX4 under way, why can't print Russian? (print HP2055dn).
http://community.qnx.com/sf/go/post113906
非常感谢您的帮助,请问您的意思是我打印机设置有问题吗?另外,您的图片是windows下的打印机驱动软件吗?我在QNX4下如何能设置这个选项?wenwei wenwei(deleted)2015-06-02T14:19:41Zpost113903: 回复: The use of LPD QNX4 under way, why can't print Russian? (print HP2055dn).
http://community.qnx.com/sf/go/post113903
chinese:
非常感谢您的帮助,请问您的意思是我打印机设置有问题吗?另外,您的图片是windows下的打印机驱动软件吗?我在QNX4下如何能设置这个选项?
english:
Thank you very much for your help. May I help you? In addition, your picture is Windows printer driver software? How can I set up this option under QNX4?
------------------ 原始邮件 ------------------
发件人: "Олег Большаков";<community-noreply@qnx.com>;
发送时间: 2015年6月2日(星期二) 凌晨1:46
收件人: "qnx4-community@community.qnx.com"<qnx4-community@community.qnx.com>;
主题: Re: The use of LPD QNX4 under way, why can't print Russian? (print HP2055dn).
Hello,
It seems that your printcap file is correct. I have HP LaserJet P2015 printer that should be similar yours I guess. Please check Settings / PCL5e / Symbol set option. You have to set this option to PC866CYR to print plain text in Cyrillic IBM866 encoding (default Russian encoding for QNX4 console). Please see attached image. If this won't work then send me example of file that you're printing.
Respectfully,
Oleg
30 мая 2015 г., в 18:35, wenwei wenwei <community-noreply@qnx.com> написал:
Our company IPC using QNX4.25 operating system and licenses all installation, equipped with laser network printer HP P2055dn a (Russian character, no Chinese font).
Now want to use LPD to print a TXT file, the contents of the txt file is russian. But print garbled, and wrap is not correct. If the txt file is English, you can print correctly.
A self-examination of the printer, can play a normal Russian character. Did I have a mistake in setting the QNX? Or I am not configured?
Specific methods are as follows:
1, the normal use of the network card, the Ping printer (set the printer address is 192.168.16.53)
2, /etc/printcap:
#
P2055dn|P2055dn:\
: rm=192.168.16.53:rp=p2055dn:\
: sd=/usr/spool/output/p2055dn:sh=false:
3, /etc/config/lpsrvr:
#
Example LPSRVR configuration file #
#
This example creates a single device # called "/dev/spool/ps.phs" which
Will support multiple Photon print streams # and give them
At a time to # one the physical Postscript printer connected to "/dev/par1".
#
# Use "lpsrvr & -fThisFile" to make it all happen (put in sysinit)
[]
Define QNX name of this print # spooler
# sp=/qnx/PhSpool
Specify where spool files are kept # (lpsrvr will delete them for you)
# cd=/tmp
[Phps]
Use the Postscript Filter and Feed # into Raw Queue
Ta=nullpt
-l1 co=/usr/photon/bin/Pp.ps $(SPFILE) -Pp2055dn /usr/ucb/lpr
[Phpcl]
Use the PCL Filter and Feed # into Raw Queue
Ta=nullpt
Co=/usr/photon/bin/Pp.pcl $(SPFILE) -Pp2055dn /usr/ucb/lpr
[Phpsc]
Use the Postscript Filter and Feed # into Raw Queue
Ta=nullpt
-l1 co=/usr/photon/bin/Pp.ps $(SPFILE) -Pc2025dn /usr/ucb/lpr
[Phpclc]
Use the PCL Filter and Feed # into Raw Queue
Ta=nullpt
Co=/usr/photon/bin/Pp.pcl $(SPFILE) -Pc2025dn /usr/ucb/lpr
[t]
Ta=nullpt
-Pp2055dn co=/usr/ucb/lpr $(SPFILE)
[tfake]
Co=cat "$(SPFILE)" "$(device)" "
Ta=lptl0
[-lptl]
Dv=/dev/par1
[-lptl0]
Dv=/.registry.log
[-nullpt]
Dv=/dev/null
4, running print command
#lpsrvr &
#lpd &
-Pp2055dn /tmp/1.txt #lpr
I don't know that the /etc/config/sysinit.8 settings will also have a impact, I post it all up
/bin/Fsys #Image:
/bin/Fsys.eide Fsys -Ndsk0 -n0=hd0. -n5=cd0. Eide -a1f0 -i14 #Image:
/bin/mount -p /dev/hd0.0 /dev/hd0.0t77 #Image: /
/bin/sinit TERM=qnxm #Image:
NODE=48 #export
KBD=ru_RU_102.kbd export
ABLANG=ru export
TZ=mst-08 M3.5.0/2, M10.5.0/2, export
-l at /bin/rtc
Dev &
Pipe &
-Q -n6 Dev.ansi &
/dev/con1 reopen
-A /dev/console=/dev/con1 prefix
Dev.par &
-n16 Dev.pty &
# /bin/Fsys.floppy -a3f0 -i6
# /cd=/dev/cd0.0 & /bin/Iso9660fsys
# Define the default CD Rom
# /bin/prefix -A /cd=//0/cd0.0
# mount /dev/fd0 /fd/fd0
-P chkfsys /
/bin/mcyr &
-r license
Nameloc &
LPSRVR=/qnx/spooler export
-f1 /etc/config/cfont/unim.f8 cfont
-f0 /etc/config/cfont/vga cfont!.f16
-a -d Mqueue &
LOGNAME=mag export
/etc/netstart
-c -t "-p -f root login" /dev/con1 tinit &
-c -T "-p -f root login" /dev/con[2-6] tinit &
_______________________________________________
QNX4 Community Support
http://community.qnx.com/sf/go/post113878
To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comwenwei wenwei(deleted)2015-06-02T14:12:18Zpost113891: Re: The use of LPD QNX4 under way, why can't print Russian? (print HP2055dn).
http://community.qnx.com/sf/go/post113891
Hello,
It seems that your printcap file is correct. I have HP LaserJet P2015 printer that should be similar yours I guess. Please check Settings / PCL5e / Symbol set option. You have to set this option to PC866CYR to print plain text in Cyrillic IBM866 encoding (default Russian encoding for QNX4 console). Please see attached image. If this won't work then send me example of file that you're printing.
Respectfully,
Oleg
30 мая 2015 г., в 18:35, wenwei wenwei <community-noreply@qnx.com<mailto:community-noreply@qnx.com>> написал:
Our company IPC using QNX4.25 operating system and licenses all installation, equipped with laser network printer HP P2055dn a (Russian character, no Chinese font).
Now want to use LPD to print a TXT file, the contents of the txt file is russian. But print garbled, and wrap is not correct. If the txt file is English, you can print correctly.
A self-examination of the printer, can play a normal Russian character. Did I have a mistake in setting the QNX? Or I am not configured?
Specific methods are as follows:
1, the normal use of the network card, the Ping printer (set the printer address is 192.168.16.53)
2, /etc/printcap:
#
P2055dn|P2055dn:\
: rm=192.168.16.53:rp=p2055dn:\
: sd=/usr/spool/output/p2055dn:sh=false:
3, /etc/config/lpsrvr:
#
Example LPSRVR configuration file #
#
This example creates a single device # called "/dev/spool/ps.phs" which
Will support multiple Photon print streams # and give them
At a time to # one the physical Postscript printer connected to "/dev/par1".
#
# Use "lpsrvr & -fThisFile" to make it all happen (put in sysinit)
[]
Define QNX name of this print # spooler
# sp=/qnx/PhSpool
Specify where spool files are kept # (lpsrvr will delete them for you)
# cd=/tmp
[Phps]
Use the Postscript Filter and Feed # into Raw Queue
Ta=nullpt
-l1 co=/usr/photon/bin/Pp.ps $(SPFILE) -Pp2055dn /usr/ucb/lpr
[Phpcl]
Use the PCL Filter and Feed # into Raw Queue
Ta=nullpt
Co=/usr/photon/bin/Pp.pcl $(SPFILE) -Pp2055dn /usr/ucb/lpr
[Phpsc]
Use the Postscript Filter and Feed # into Raw Queue
Ta=nullpt
-l1 co=/usr/photon/bin/Pp.ps $(SPFILE) -Pc2025dn /usr/ucb/lpr
[Phpclc]
Use the PCL Filter and Feed # into Raw Queue
Ta=nullpt
Co=/usr/photon/bin/Pp.pcl $(SPFILE) -Pc2025dn /usr/ucb/lpr
[t]
Ta=nullpt
-Pp2055dn co=/usr/ucb/lpr $(SPFILE)
[tfake]
Co=cat "$(SPFILE)" "$(device)" "
Ta=lptl0
[-lptl]
Dv=/dev/par1
[-lptl0]
Dv=/.registry.log
[-nullpt]
Dv=/dev/null
4, running print command
#lpsrvr &
#lpd &
-Pp2055dn /tmp/1.txt #lpr
I don't know that the /etc/config/sysinit.8 settings will also have a impact, I post it all up
/bin/Fsys #Image:
/bin/Fsys.eide Fsys -Ndsk0 -n0=hd0. -n5=cd0. Eide -a1f0 -i14 #Image:
/bin/mount -p /dev/hd0.0 /dev/hd0.0t77 #Image: /
/bin/sinit TERM=qnxm #Image:
NODE=48 #export
KBD=ru_RU_102.kbd export
ABLANG=ru export
TZ=mst-08 M3.5.0/2, M10.5.0/2, export
-l at /bin/rtc
Dev &
Pipe &
-Q -n6 Dev.ansi &
/dev/con1 reopen
-A /dev/console=/dev/con1 prefix
Dev.par &
-n16 Dev.pty &
# /bin/Fsys.floppy -a3f0 -i6
# /cd=/dev/cd0.0 & /bin/Iso9660fsys
# Define the default CD Rom
# /bin/prefix -A /cd=//0/cd0.0
# mount /dev/fd0 /fd/fd0
-P chkfsys /
/bin/mcyr &
-r license
Nameloc &
LPSRVR=/qnx/spooler export
-f1 /etc/config/cfont/unim.f8 cfont
-f0 /etc/config/cfont/vga cfont!.f16
-a -d Mqueue &
LOGNAME=mag export
/etc/netstart
-c -t "-p -f root login" /dev/con1 tinit &
-c -T "-p -f root login" /dev/con[2-6] tinit &
_______________________________________________
QNX4 Community Support
http://community.qnx.com/sf/go/post113878
To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
[cid:BF9E923E-E355-4965-B804-561B5F3DB775@fallback]Oleg Bolshakov2015-06-01T17:47:00Zpost113878: The use of LPD QNX4 under way, why can't print Russian? (print HP2055dn).
http://community.qnx.com/sf/go/post113878
Our company IPC using QNX4.25 operating system and licenses all installation, equipped with laser network printer HP P2055dn a (Russian character, no Chinese font).
Now want to use LPD to print a TXT file, the contents of the txt file is russian. But print garbled, and wrap is not correct. If the txt file is English, you can print correctly.
A self-examination of the printer, can play a normal Russian character. Did I have a mistake in setting the QNX? Or I am not configured?
Specific methods are as follows:
1, the normal use of the network card, the Ping printer (set the printer address is 192.168.16.53)
2, /etc/printcap:
#
P2055dn|P2055dn:\
: rm=192.168.16.53:rp=p2055dn:\
: sd=/usr/spool/output/p2055dn:sh=false:
3, /etc/config/lpsrvr:
#
Example LPSRVR configuration file #
#
This example creates a single device # called "/dev/spool/ps.phs" which
Will support multiple Photon print streams # and give them
At a time to # one the physical Postscript printer connected to "/dev/par1".
#
# Use "lpsrvr & -fThisFile" to make it all happen (put in sysinit)
[]
Define QNX name of this print # spooler
# sp=/qnx/PhSpool
Specify where spool files are kept # (lpsrvr will delete them for you)
# cd=/tmp
[Phps]
Use the Postscript Filter and Feed # into Raw Queue
Ta=nullpt
-l1 co=/usr/photon/bin/Pp.ps $(SPFILE) -Pp2055dn /usr/ucb/lpr
[Phpcl]
Use the PCL Filter and Feed # into Raw Queue
Ta=nullpt
Co=/usr/photon/bin/Pp.pcl $(SPFILE) -Pp2055dn /usr/ucb/lpr
[Phpsc]
Use the Postscript Filter and Feed # into Raw Queue
Ta=nullpt
-l1 co=/usr/photon/bin/Pp.ps $(SPFILE) -Pc2025dn /usr/ucb/lpr
[Phpclc]
Use the PCL Filter and Feed # into Raw Queue
Ta=nullpt
Co=/usr/photon/bin/Pp.pcl $(SPFILE) -Pc2025dn /usr/ucb/lpr
[t]
Ta=nullpt
-Pp2055dn co=/usr/ucb/lpr $(SPFILE)
[tfake]
Co=cat "$(SPFILE)" "$(device)" "
Ta=lptl0
[-lptl]
Dv=/dev/par1
[-lptl0]
Dv=/.registry.log
[-nullpt]
Dv=/dev/null
4, running print command
#lpsrvr &
#lpd &
-Pp2055dn /tmp/1.txt #lpr
I don't know that the /etc/config/sysinit.8 settings will also have a impact, I post it all up
/bin/Fsys #Image:
/bin/Fsys.eide Fsys -Ndsk0 -n0=hd0. -n5=cd0. Eide -a1f0 -i14 #Image:
/bin/mount -p /dev/hd0.0 /dev/hd0.0t77 #Image: /
/bin/sinit TERM=qnxm #Image:
NODE=48 #export
KBD=ru_RU_102.kbd export
ABLANG=ru export
TZ=mst-08 M3.5.0/2, M10.5.0/2, export
-l at /bin/rtc
Dev &
Pipe &
-Q -n6 Dev.ansi &
/dev/con1 reopen
-A /dev/console=/dev/con1 prefix
Dev.par &
-n16 Dev.pty &
# /bin/Fsys.floppy -a3f0 -i6
# /cd=/dev/cd0.0 & /bin/Iso9660fsys
# Define the default CD Rom
# /bin/prefix -A /cd=//0/cd0.0
# mount /dev/fd0 /fd/fd0
-P chkfsys /
/bin/mcyr &
-r license
Nameloc &
LPSRVR=/qnx/spooler export
-f1 /etc/config/cfont/unim.f8 cfont
-f0 /etc/config/cfont/vga cfont!.f16
-a -d Mqueue &
LOGNAME=mag export
/etc/netstart
-c -t "-p -f root login" /dev/con1 tinit &
-c -T "-p -f root login" /dev/con[2-6] tinit &wenwei wenwei(deleted)2015-05-30T15:35:45Zpost113858: Re: QNX timer query
http://community.qnx.com/sf/go/post113858
Hi Divya,
You asked question in QNX 4 project. Please ask it in QNX Neutrino (QNX 6) project.
Respectfully,
Oleg
25 мая 2015 г., в 8:15:37, Divya Bettampady <community-noreply@qnx.com> написал:
> Hello Oleg,
>
> I set the timer parameters as shown below:
>
> struct itimerspec itime;
> struct _pulse pl;
> int rcvid;
> float ms_interval = 5.3;
>
> itime.it_value.tv_sec = 0;
> itime.it_value.tv_nsec = ms_interval * 1000000;
> itime.it_interval.tv_sec = 0;
> itime.it_interval.tv_nsec = ms_interval * 1000000;
> timer_settime(timer_id, 0, &itime, NULL);
>
> while(1)
> {
> rcvid = MsgReceive(chid, &pl, sizeof(pl), NULL);
> if (rcvid == 0)
> { /* we got a pulse */
> if (pl.code == TIMER_START_PULSE)
> {
> printf("we got a pulse from our timer\n");
> }
> }
> }
>
>
> Thanks,
> Divya
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post113853
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2015-05-25T14:34:53Zpost113854: Re: QNX timer query
http://community.qnx.com/sf/go/post113854
Hello Oleg,
I measure the timer interval uses kernel traces captured using tracelogger.
Thanks,
DivyaDivya Bettampady(deleted)2015-05-25T05:16:31Zpost113853: Re: QNX timer query
http://community.qnx.com/sf/go/post113853
Hello Oleg,
I set the timer parameters as shown below:
struct itimerspec itime;
struct _pulse pl;
int rcvid;
float ms_interval = 5.3;
itime.it_value.tv_sec = 0;
itime.it_value.tv_nsec = ms_interval * 1000000;
itime.it_interval.tv_sec = 0;
itime.it_interval.tv_nsec = ms_interval * 1000000;
timer_settime(timer_id, 0, &itime, NULL);
while(1)
{
rcvid = MsgReceive(chid, &pl, sizeof(pl), NULL);
if (rcvid == 0)
{ /* we got a pulse */
if (pl.code == TIMER_START_PULSE)
{
printf("we got a pulse from our timer\n");
}
}
}
Thanks,
DivyaDivya Bettampady(deleted)2015-05-25T05:15:37Zpost113850: Re: QNX timer query
http://community.qnx.com/sf/go/post113850
Hi Divya,
How do you measure the time interval? What is ticksize set on your system?
Respectfully,
Oleg
22 мая 2015 г., в 13:17:34, Divya Bettampady <community-noreply@qnx.com> написал:
> Hello,
>
> I want to use QNX timer to get clock resolution in terms of millisecond. I am successful in getting resolution in terms of integer values such as 32ms, 16ms, and even 1ms.
>
> But when I set the timer interval to 5.3ms, the timer times out in non-uniform intervals (5ms, 5ms, 6ms, 5ms....). What might be the cause for this behavior?
>
> Thank you in advance.
>
> Best Regards,
> Divya
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post113847
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2015-05-22T12:20:02Zpost113847: QNX timer query
http://community.qnx.com/sf/go/post113847
Hello,
I want to use QNX timer to get clock resolution in terms of millisecond. I am successful in getting resolution in terms of integer values such as 32ms, 16ms, and even 1ms.
But when I set the timer interval to 5.3ms, the timer times out in non-uniform intervals (5ms, 5ms, 6ms, 5ms....). What might be the cause for this behavior?
Thank you in advance.
Best Regards,
DivyaDivya Bettampady(deleted)2015-05-22T10:17:34Zpost113838: Re: Unable to boot from USB - QNX 6.5
http://community.qnx.com/sf/go/post113838
Hi Manas,
This is QNX 4 project. Please repeat your question in QNX 6 project to get answer.
Respectfully,
Oleg
20 мая 2015 г., в 17:14:00, manas sahoo <community-noreply@qnx.com> написал:
> I am trying to boot from USB. did the following steps
> 1) Delete all usb partitions
> 2) fdisk /dev/hd0 add -s 1 -b -t 11 -p 20
> 3) fdisk /dev/hd0 add -s 2 -b -t 77 -p 60
> 4) dinit -hq -f bios.ifs /dev/hd0t77
> 5) dloader /dev/hd0t11 /bin/ipl-diskpc1
> 6) dloader /dev/hd0t77 /bin/ipl-diskpc2
>
> After this when I boot the board from USB, i see this
>
> Boots almost fine but stops after
>
> Hit Esc for .altboot............................................................
> .................
>
> Any help here. I am stuck.
>
> Regards,
> Manas
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post113835
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2015-05-20T15:16:50Zpost113835: Unable to boot from USB - QNX 6.5
http://community.qnx.com/sf/go/post113835
I am trying to boot from USB. did the following steps
1) Delete all usb partitions
2) fdisk /dev/hd0 add -s 1 -b -t 11 -p 20
3) fdisk /dev/hd0 add -s 2 -b -t 77 -p 60
4) dinit -hq -f bios.ifs /dev/hd0t77
5) dloader /dev/hd0t11 /bin/ipl-diskpc1
6) dloader /dev/hd0t77 /bin/ipl-diskpc2
After this when I boot the board from USB, i see this
Boots almost fine but stops after
Hit Esc for .altboot............................................................
.................
Any help here. I am stuck.
Regards,
Manasmanas sahoo2015-05-20T14:14:00Zpost113550: Re: Board Support Package for Raspberry Pi
http://community.qnx.com/sf/go/post113550
Hi Paul,
I very doubt that QNX 4 will support ARM CPU. It should be better to ask in QNX Neutrino (QNX 6) discussion board.
Respectfully,
Oleg
12 марта 2015 г., в 19:32, Paul Thomas <community-noreply@qnx.com> написал:
>
> Are there any plans to produce a BSP for the Raspberry Pi?
> (or other popular SOC single board computer)?
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post113548
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2015-03-12T17:51:36Zpost113549: Re: Configuring dual displays for Photon
http://community.qnx.com/sf/go/post113549
Hi Paul,
I have built dual display configuration using Photon 1.14 as described in the technical notes. I’ve used Intel graphics controller (Pg.i830) and discrete adapter (Pg.flat). In general you need integrated Intel controller that supported by Pg.i830 or Pg.intelhd and any addition video card that supported by Hydra.ms/Pg.flat.
Also try new experimental multi-monitor driver Pg.i915 from Latest Software Updates page:
http://community.qnx.com/sf/wiki/do/viewPage/projects.qnx4/wiki/LatestSoftwareUpdates
Respectfully,
Oleg
12 марта 2015 г., в 18:46, Paul Thomas <community-noreply@qnx.com> написал:
> This technical note is from March, 2000:
> http://www.qnx.com/developers/qnx4/qnx4kb/solution.html?code=9490
>
> Has anyone achieved dual displays using Photon 1.14?
>
> What video cards did you use?
> Can they still be purchased in 2015?
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post113542
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2015-03-12T17:45:37Zpost113548: Board Support Package for Raspberry Pi
http://community.qnx.com/sf/go/post113548
Are there any plans to produce a BSP for the Raspberry Pi?
(or other popular SOC single board computer)?Paul Thomas(deleted)2015-03-12T16:32:44Zpost113542: Configuring dual displays for Photon
http://community.qnx.com/sf/go/post113542
This technical note is from March, 2000:
http://www.qnx.com/developers/qnx4/qnx4kb/solution.html?code=9490
Has anyone achieved dual displays using Photon 1.14?
What video cards did you use?
Can they still be purchased in 2015?Paul Thomas(deleted)2015-03-12T15:46:28Zpost113527: Re: I want to share a QNX 4.25 folder and access it from Windows
http://community.qnx.com/sf/go/post113527
Hi Louis,
Please find attached Samba 2.0.7 binaries and readme for QNX4. Also you can download more recent version of Samba 2.2.12 from the link below:
http://forum.kpda.ru/index.php/topic,582.0.html
Respectfully,
Oleg
10 марта 2015 г., в 1:52:34, Louis Francoeur <community-noreply@qnx.com> написал:
> Is there a way to share a folder in QNX 4.25 that will be accessible from a Windows connected drive letter ? For exemple, from Windows Explorer I want to see the letter M:\ and if I browse it, it gives me the content of /usr/shared of my QNX 4.25 system? I know that "Samba" may do this but I can't find it on www.qnx.com. Is someone could help me?
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post113525
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2015-03-10T07:00:17Zpost113525: I want to share a QNX 4.25 folder and access it from Windows
http://community.qnx.com/sf/go/post113525
Is there a way to share a folder in QNX 4.25 that will be accessible from a Windows connected drive letter ? For exemple, from Windows Explorer I want to see the letter M:\ and if I browse it, it gives me the content of /usr/shared of my QNX 4.25 system? I know that "Samba" may do this but I can't find it on www.qnx.com. Is someone could help me?Louis Francoeur(deleted)2015-03-09T22:52:34Zpost113220: Re: How to write Applications for QNX Connected Car Hardware
http://community.qnx.com/sf/go/post113220
This particular forum you are in is for QNX 4 questions.
Since QNX Connected CAR is QNX 6 based, your questions would get more responses in one of the QNX 6 forum groups.Dave Nickerson2015-02-04T17:14:59Zpost113145: Re: How to write Applications for QNX Connected Car Hardware
http://community.qnx.com/sf/go/post113145
Hi Kerry,
I am planning to develop applications for media play, I work for a company called AetherPal.shiva aetherpal(deleted)2015-01-29T18:57:33Zpost113144: Re: How to write Applications for QNX Connected Car Hardware
http://community.qnx.com/sf/go/post113144
Shiva,
Can you tell me what type of application you are writing? Also, which company are you with?
Thanks,
Kerry Johnson
Product Manager - AutomotiveKerry Johnson2015-01-29T17:57:09Zpost113122: How to write Applications for QNX Connected Car Hardware
http://community.qnx.com/sf/go/post113122
I am planning to write applications to run on QNX Connected car. I already setup QNX SDP and
QNX target on my machine. But I can not still get what else I need to proceed further.
1. which IDE should I use for this? QNX Momentics or Eclipse or something else?
2. Do I need to buy a QNX hardware board for connected car development, or Target created on VMware would be sufficient?
3. Do I need to purchase any license for connected car development?
Thanks
Shivashiva aetherpal(deleted)2015-01-28T20:45:01Zpost113001: Re: Fsys.ahci
http://community.qnx.com/sf/go/post113001
> Hi Pekka!
>
> Unfortunately, it seems like community portal engine issue. All tar.gz
> archives are downloading double gzipped. To unpack double gzipped archive you
> should ungzip it twice:
>
> $ zcat Fsys.ahci.tar.gz | zcat | tar xf
>
> Or you can fix downloaded archive:
>
> $ zcat Fsys.ahci.tar.gz > Fsys.ahci_fixed.tar.gz
>
> I recommend using archives to transfer files. In this case file attributes are
> preserved.
>
> Respectfully,
> Oleg
>
> 14 янв. 2015 г., в 16:01:52, Pekka Tuusjärvi <community-noreply@qnx.com> написал:
>
> > Hello, I get archive is corrupt error If i try to extract archive?
> >
> >
> >
> > _______________________________________________
> >
> > QNX4 Community Support
> > http://community.qnx.com/sf/go/post112933
> > To cancel your subscription to this discussion, please e-mail qnx4-community
> -unsubscribe@community.qnx.com
>
Hi and thanks for the info. The fix seems to work fine in my test pc. So big thanks everyone who participated to fix this problem.Pekka Tuusjärvi(deleted)2015-01-20T06:58:54Zpost112937: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112937
Hi Pekka!
Unfortunately, it seems like community portal engine issue. All tar.gz archives are downloading double gzipped. To unpack double gzipped archive you should ungzip it twice:
$ zcat Fsys.ahci.tar.gz | zcat | tar xf
Or you can fix downloaded archive:
$ zcat Fsys.ahci.tar.gz > Fsys.ahci_fixed.tar.gz
I recommend using archives to transfer files. In this case file attributes are preserved.
Respectfully,
Oleg
14 янв. 2015 г., в 16:01:52, Pekka Tuusjärvi <community-noreply@qnx.com> написал:
> Hello, I get archive is corrupt error If i try to extract archive?
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post112933
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2015-01-14T14:30:20Zpost112935: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112935
And
Fsys.ahci driver
cksum Fsys.ahci
2031912476 145562 Fsys.ahciVladimir Makhilev2015-01-14T13:45:37Zpost112934: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112934
Hi Pekka,
Seems like both archives are broken.
Please try attached Dev.ser driver
cksum Dev.ser
1146694106 29093 Dev.ser
--
Best regards,
VladimirVladimir Makhilev2015-01-14T13:33:47Zpost112933: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112933
Hello, I get archive is corrupt error If i try to extract archive?Pekka Tuusjärvi(deleted)2015-01-14T13:01:52Zpost112915: Re: QNX4 installation in VirtualBox
http://community.qnx.com/sf/go/post112915
I've tried current version of VirtualBox (4.3.20) and installation of QNX was successfull without any problems. It looks like a problem of specific previous version of VirtualBox. Thanks for your feedback.Martin Michalek(deleted)2015-01-13T07:39:49Zpost112829: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112829
Thank you very much. I will try when I get back to my office. :)Pekka Tuusjärvi(deleted)2015-01-05T21:04:24Zpost112793: Regarding framebuffer concept in QNX 4.25.
http://community.qnx.com/sf/go/post112793
Dear Oleg,
Thank you for your valuable support.
We were trying to understand the concepts which you discussed in your earlier reply to use the frame buffer pointer in QNX 4.25. Please see our replies inline.
[Oleg] >> You can create at least two configurations with Photon components to achieve your target.
You can disable (just do not launch) all unneeded Photon components like pdm, pwm, etc and create PtRaw-based application maximized to whole screen.
[Honey] >> We have edited our ph script as follows:
Added the following lines.
1. export PHWM=""
2. export PHWMOPTS=""
3. export PHPDM_DISABLE=""
and commented out pdm invokation in the script.
Then we rebooted our QNX 4.25 machine. We ensured that pdm, pwm are not running by running pidin command.
Then we started learning on PtRaw widget from "Raw drawing and animation" chapter from Photon MicroGUI manual.
Created a sample application which has a PtRaw widget and a PtRect canvas placed on it. Also draw an ellipse and fill color on it. This is what we can achieve till now.
Hope this is the way you mentioned how to get the raw drawing feature using frame buffer. Please correct us if we are wrong.
[Oleg] >> Also you can try to launch Hydra.ms to switch to graphics mode and access framebuffer directly using framebuffer pointer. To get framebuffer pointer you can use show_pci or show_vesa utils.
[Honey] >> We can't understand this fully. We have tried to run show_pci command. Attached file (show_pci.jpg) is the output which we got. show_vesa command is not found in our QNX 4.25 machine.
Also we are not clear about Hydra.ms; so didn't make a trial on it. How hydra.ms can be used to access frame buffer directly?
Could you please detail on our concerns?
Thank you for your understanding and patience.
Regards,
Honey S
________________________________
Confidentiality Statement / Disclaimer : This message and any attachments is intended for the sole use of the intended recipient. It may contain confidential information. Any unauthorized use, dissemination or modification is strictly prohibited. If you are not the intended recipient, please notify the sender immediately then delete it from all your systems, and do not copy, use or print. Internet communications are not secure and it is the responsibility of the recipient to make sure that it is virus/malicious code exempt.
The company/sender cannot be responsible for any unauthorized alterations or modifications made to the contents. If you require any form of confirmation of the contents, please contact the company/sender. The company/sender is not liable for any errors or omissions in the content of this message.
________________________________Honey S(deleted)2014-12-29T07:48:59Zpost112791: Recall: Regarding framebuffer concept in QNX 4.25.
http://community.qnx.com/sf/go/post112791
Honey S. would like to recall the message, "Regarding framebuffer concept in QNX 4.25.".
________________________________
Confidentiality Statement / Disclaimer : This message and any attachments is intended for the sole use of the intended recipient. It may contain confidential information. Any unauthorized use, dissemination or modification is strictly prohibited. If you are not the intended recipient, please notify the sender immediately then delete it from all your systems, and do not copy, use or print. Internet communications are not secure and it is the responsibility of the recipient to make sure that it is virus/malicious code exempt.
The company/sender cannot be responsible for any unauthorized alterations or modifications made to the contents. If you require any form of confirmation of the contents, please contact the company/sender. The company/sender is not liable for any errors or omissions in the content of this message.
________________________________Honey S(deleted)2014-12-29T07:47:59Zpost112789: Regarding framebuffer concept in QNX 4.25.
http://community.qnx.com/sf/go/post112789
Dear Oleg,
Thank you for your valuable support.
We were trying to understand the concepts which you discussed in your earlier reply to use the frame buffer pointer in QNX 4.25. Please see our replies inline.
[Oleg] >> You can create at least two configurations with Photon components to achieve your target.
You can disable (just do not launch) all unneeded Photon components like pdm, pwm, etc and create PtRaw-based application maximized to whole screen.
[Honey] >> We have edited our ph script as follows:
Added the following lines.
1. export PHWM=""
2. export PHWMOPTS=""
3. export PHPDM_DISABLE=""
and commented out pdm invokation in the script.
Then we rebooted our QNX 4.25 machine. We ensured that pdm, pwm are not running by running pidin command.
Then we started learning on PtRaw widget from "Raw drawing and animation" chapter from Photon MicroGUI manual.
Created a sample application which has a PtRaw widget and a PtRect canvas placed on it. Also draw an ellipse and fill color on it. This is what we can achieve till now.
Hope this is the way you mentioned how to get the raw drawing feature using frame buffer. Please correct us if we are wrong.
[Oleg] >> Also you can try to launch Hydra.ms to switch to graphics mode and access framebuffer directly using framebuffer pointer. To get framebuffer pointer you can use show_pci or show_vesa utils.
[Honey] >> We can't understand this fully. We have tried to run show_pci command. Attached file (show_pci.png) is the output which we got. show_vesa command is not found in our QNX 4.25 machine.
Also we are not clear about Hydra.ms; so didn't make a trial on it. How hydra.ms can be used to access frame buffer directly?
Could you please detail on our concerns?
Thank you for your understanding and patience.
Regards,
Honey S
________________________________
Confidentiality Statement / Disclaimer : This message and any attachments is intended for the sole use of the intended recipient. It may contain confidential information. Any unauthorized use, dissemination or modification is strictly prohibited. If you are not the intended recipient, please notify the sender immediately then delete it from all your systems, and do not copy, use or print. Internet communications are not secure and it is the responsibility of the recipient to make sure that it is virus/malicious code exempt.
The company/sender cannot be responsible for any unauthorized alterations or modifications made to the contents. If you require any form of confirmation of the contents, please contact the company/sender. The company/sender is not liable for any errors or omissions in the content of this message.
________________________________Honey S(deleted)2014-12-29T07:46:47Zpost112758: OpenWatcom compiler error in QNX 4.25
http://community.qnx.com/sf/go/post112758
Our QNX 4.25 machine has Watcom 10.6 and Watcom 9.52 already installed;
but it is having some license issue while compiling CPP files.
So we are trying to use OpenWatcom compiler on our QNX 4.25 machine.
We recently found the Open Watcom Source for QNX from:
http://sourceforge.net/projects/openwatcomqnx4/files/
We have copied the binary to our QNX 4.25. But on compiling
a sample CPP file using this compiler, we are getting these errors from the include file,
/usr/include/iostream.h(323) : Error! E059 : col(21) unable to open 'streambu.h'
/usr/include/iostream.h(323) : Note! N393: col(21) included from cpptest.cpp(1)
Could you please some shed some light onto our issue?
Thanking you in advance,
Thanking you,
Honey S
________________________________
Confidentiality Statement / Disclaimer : This message and any attachments is intended for the sole use of the intended recipient. It may contain confidential information. Any unauthorized use, dissemination or modification is strictly prohibited. If you are not the intended recipient, please notify the sender immediately then delete it from all your systems, and do not copy, use or print. Internet communications are not secure and it is the responsibility of the recipient to make sure that it is virus/malicious code exempt.
The company/sender cannot be responsible for any unauthorized alterations or modifications made to the contents. If you require any form of confirmation of the contents, please contact the company/sender. The company/sender is not liable for any errors or omissions in the content of this message.
________________________________Honey S(deleted)2014-12-22T12:32:23Zpost112748: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112748
Also please try attached Fsys.ahci driver.
This version checks interrupt status in interrupt handler and if it's not an ahci
interrupt it skips it without masking/unmasking the interrupt.
cksum Fsys.ahci.tar.gz
3556589980 82115 Fsys.ahci.tar.gz
--
With best regards,
VladimirVladimir Makhilev2014-12-19T09:02:32Zpost112747: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112747
Hi Pekka,
Please try attached Dev.ser driver.
cksum Dev.ser.tar.gz
3280607655 15535 Dev.ser.tar.gz
--
With best regards,
VladimirVladimir Makhilev2014-12-19T08:54:25Zpost112716: Re: How to configure voyager backend in QNX4.25
http://community.qnx.com/sf/go/post112716
Hello,
I've answered here: http://community.qnx.com/sf/discussion/do/listPosts/projects.qnx4/discussion.general.topc25894
Respectfully,
Oleg
15 дек. 2014 г., в 8:46:59, Honey S. <community-noreply@qnx.com> написал:
> Dear all,
>
> We are trying to find out how to configure the back end rendering engine in Voyager browser used in QNX4.25.
> We understood it run with voyager.server rendering engine by default.
> We checked the availability of /etc/photon/webservers file in QNX4.25. But we failed to find it.
> Could you please share your thoughts on our concern.
>
> Thanking you,
> Honey S
>
> Confidentiality Statement / Disclaimer : This message and any attachments is intended for the sole use of the intended recipient. It may contain confidential information. Any unauthorized use, dissemination or modification is strictly prohibited. If you are not the intended recipient, please notify the sender immediately then delete it from all your systems, and do not copy, use or print. Internet communications are not secure and it is the responsibility of the recipient to make sure that it is virus/malicious code exempt.
>
> The company/sender cannot be responsible for any unauthorized alterations or modifications made to the contents. If you require any form of confirmation of the contents, please contact the company/sender. The company/sender is not liable for any errors or omissions in the content of this message.
>Oleg Bolshakov2014-12-17T13:55:44Zpost112712: Re: Framebuffer concept in QNX4.25
http://community.qnx.com/sf/go/post112712
Hello,
You can create at least two configurations with Photon components to achieve your target. You can disable (just do not launch) all unneeded Photon components like pdm, pwm, etc and create PtRaw-based application maximized to whole screen. Also you can try to launch Hydra.ms to switch to graphics mode and access framebuffer directly using framebuffer pointer. To get framebuffer pointer you can use show_pci or show_vesa utils.
What is a reason to do not use Photon? If you describe your question more details then I'll try to suggest more appropriate option.
Respectfully,
Oleg
15 дек. 2014 г., в 8:44:31, Honey S. <community-noreply@qnx.com> написал:
> Dear all,
> Is there any framebuffer concept in QNX4.25?
> We need to check if any graphics applications can be run in QNX4.25 without using Photon GUI toolkit support
> and by accessing framebuffer directly.
> We understood that QNX6.4.x supports SDL (libSDL) and using this we can get a framebuffer interface.
> But is SDL supported in QNX4.25?
>
> Thanking you,
> Honey S
> Senior Software Engineer
> QuEST Global Engineering Services Pvt Ltd
> Technopark
> Trivandrum
>
> Confidentiality Statement / Disclaimer : This message and any attachments is intended for the sole use of the intended recipient. It may contain confidential information. Any unauthorized use, dissemination or modification is strictly prohibited. If you are not the intended recipient, please notify the sender immediately then delete it from all your systems, and do not copy, use or print. Internet communications are not secure and it is the responsibility of the recipient to make sure that it is virus/malicious code exempt.
>
> The company/sender cannot be responsible for any unauthorized alterations or modifications made to the contents. If you require any form of confirmation of the contents, please contact the company/sender. The company/sender is not liable for any errors or omissions in the content of this message.
>Oleg Bolshakov2014-12-17T13:14:53Zpost112676: How to configure voyager backend in QNX4.25
http://community.qnx.com/sf/go/post112676
Dear all,
We are trying to find out how to configure the back end rendering engine in Voyager browser used in QNX4.25.
We understood it run with voyager.server rendering engine by default.
We checked the availability of /etc/photon/webservers file in QNX4.25. But we failed to find it.
Could you please share your thoughts on our concern.
Thanking you,
Honey S
________________________________
Confidentiality Statement / Disclaimer : This message and any attachments is intended for the sole use of the intended recipient. It may contain confidential information. Any unauthorized use, dissemination or modification is strictly prohibited. If you are not the intended recipient, please notify the sender immediately then delete it from all your systems, and do not copy, use or print. Internet communications are not secure and it is the responsibility of the recipient to make sure that it is virus/malicious code exempt.
The company/sender cannot be responsible for any unauthorized alterations or modifications made to the contents. If you require any form of confirmation of the contents, please contact the company/sender. The company/sender is not liable for any errors or omissions in the content of this message.
________________________________Honey S(deleted)2014-12-15T05:47:11Zpost112675: Framebuffer concept in QNX4.25
http://community.qnx.com/sf/go/post112675
Dear all,
Is there any framebuffer concept in QNX4.25?
We need to check if any graphics applications can be run in QNX4.25 without using Photon GUI toolkit support
and by accessing framebuffer directly.
We understood that QNX6.4.x supports SDL (libSDL) and using this we can get a framebuffer interface.
But is SDL supported in QNX4.25?
Thanking you,
Honey S
Senior Software Engineer
QuEST Global Engineering Services Pvt Ltd
Technopark
Trivandrum
________________________________
Confidentiality Statement / Disclaimer : This message and any attachments is intended for the sole use of the intended recipient. It may contain confidential information. Any unauthorized use, dissemination or modification is strictly prohibited. If you are not the intended recipient, please notify the sender immediately then delete it from all your systems, and do not copy, use or print. Internet communications are not secure and it is the responsibility of the recipient to make sure that it is virus/malicious code exempt.
The company/sender cannot be responsible for any unauthorized alterations or modifications made to the contents. If you require any form of confirmation of the contents, please contact the company/sender. The company/sender is not liable for any errors or omissions in the content of this message.
________________________________Honey S(deleted)2014-12-15T05:44:54Zpost112489: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112489
Hi Pekka,
I remember this issue. Unfortunately, the fix is not ready yet.
Respectfully,
Oleg
01 дек. 2014 г., в 14:52:36, Pekka Tuusjärvi <community-noreply@qnx.com> написал:
> Hi!
>
> Any news on this one?
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post112488
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2014-12-01T13:53:51Zpost112488: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112488
Hi!
Any news on this one?Pekka Tuusjärvi(deleted)2014-12-01T11:52:36Zpost112409: Re: env setup for QNX version 4.x
http://community.qnx.com/sf/go/post112409
just found out from an another source...
they are under
/etc/config/localPhuoc Do(deleted)2014-11-21T19:44:55Zpost112408: env setup for QNX version 4.x
http://community.qnx.com/sf/go/post112408
Hi,
Where the QNX version 4 contains all the env setup like HOST, PATH , etc?
Thanks,
pdoPhuoc Do(deleted)2014-11-21T17:10:58Zpost112403: QtWebkit on QNX4.25
http://community.qnx.com/sf/go/post112403
Dear all,
Is there anyone who tried to run QtWebkit on QNX4.25?
I understood that someone has already ported Qt on QNX4.25.
But seems it is based on a very old version of Qt (1.42).
I see that QtWebkit 2.0 is based on Qt4.x version.
I would appreciate if you could guide me in how to build QtWebkit 2.0 on QNX4.25.
Thanking you in advance,
Honey S
________________________________
Confidentiality Statement / Disclaimer : This message and any attachments is intended for the sole use of the intended recipient. It may contain confidential information. Any unauthorized use, dissemination or modification is strictly prohibited. If you are not the intended recipient, please notify the sender immediately then delete it from all your systems, and do not copy, use or print. Internet communications are not secure and it is the responsibility of the recipient to make sure that it is virus/malicious code exempt.
The company/sender cannot be responsible for any unauthorized alterations or modifications made to the contents. If you require any form of confirmation of the contents, please contact the company/sender. The company/sender is not liable for any errors or omissions in the content of this message.
________________________________Honey S(deleted)2014-11-21T11:14:41Zpost112372: Re: Voyager SDK for QNX4.25
http://community.qnx.com/sf/go/post112372
Hello,
As far as I know the Voyager SDK should be available for ordering. Also I can confirm that Voyager supports HTML 3.2.
Respectfully,
Oleg
19 нояб. 2014 г., в 7:55:10, Honey S. <community-noreply@qnx.com> написал:
> Dear all,
>
> We need to get HTML4 support on QNX4.25. For that, we understood that Voyager SDK supports upto HTML3.2.
>
> 1. Is the Voyager SDK still available to QNX 4.25 customers or is it obsolete?
> If it is obsolete, can you please tell us how we can integrate HTML 3.2/HTML 4 support to QNX4.25?
>
> 2. In some links, it is mentioned, Voyager SDK is obtained as part of Internet appliance toolkit. Where can we get this for our QNX 4.25 in order to get Voyager SDK with PtWebClient widget support?
>
> Thanking you in advance….
> Confidentiality Statement / Disclaimer : This message and any attachments is intended for the sole use of the intended recipient. It may contain confidential information. Any unauthorized use, dissemination or modification is strictly prohibited. If you are not the intended recipient, please notify the sender immediately then delete it from all your systems, and do not copy, use or print. Internet communications are not secure and it is the responsibility of the recipient to make sure that it is virus/malicious code exempt.
>
> The company/sender cannot be responsible for any unauthorized alterations or modifications made to the contents. If you require any form of confirmation of the contents, please contact the company/sender. The company/sender is not liable for any errors or omissions in the content of this message.
>Oleg Bolshakov2014-11-19T14:50:51Zpost112371: Re: QNX4 installation in VirtualBox
http://community.qnx.com/sf/go/post112371
I am using VirtualBox-3.0.6-52128-Win.exe, it is running fine for QNX4Andrej Lucny(deleted)2014-11-19T10:32:49Zpost112369: Voyager SDK for QNX4.25
http://community.qnx.com/sf/go/post112369
Dear all,
We need to get HTML4 support on QNX4.25. For that, we understood that Voyager SDK supports upto HTML3.2.
1. Is the Voyager SDK still available to QNX 4.25 customers or is it obsolete?
If it is obsolete, can you please tell us how we can integrate HTML 3.2/HTML 4 support to QNX4.25?
2. In some links, it is mentioned, Voyager SDK is obtained as part of Internet appliance toolkit. Where can we get this for our QNX 4.25 in order to get Voyager SDK with PtWebClient widget support?
Thanking you in advance....
________________________________
Confidentiality Statement / Disclaimer : This message and any attachments is intended for the sole use of the intended recipient. It may contain confidential information. Any unauthorized use, dissemination or modification is strictly prohibited. If you are not the intended recipient, please notify the sender immediately then delete it from all your systems, and do not copy, use or print. Internet communications are not secure and it is the responsibility of the recipient to make sure that it is virus/malicious code exempt.
The company/sender cannot be responsible for any unauthorized alterations or modifications made to the contents. If you require any form of confirmation of the contents, please contact the company/sender. The company/sender is not liable for any errors or omissions in the content of this message.
________________________________Honey S(deleted)2014-11-19T04:55:54Zpost112292: cincinnati milacron fantry out of rockwell tulsa
http://community.qnx.com/sf/go/post112292
I was contacted by a tech who is working on a Rockwell CNC running on QNX 4.25. Unfortunately, I had no involvement with that machine. Does any body here know the machine or someone who helped develop the software?
Thanks,
Terry LaughlinTerry Laughlin(deleted)2014-11-06T19:24:00Zpost112274: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112274
Hi Pekka,
We have reproduced your issue here. We're working on this issue. When the fix will be prepared, I'll let you know.
Respectfully,
Oleg
28 окт. 2014 г., в 9:57:54, Pekka Tuusjärvi <community-noreply@qnx.com> написал:
> Hi Pavel,
>
> here is the sin ir with Fsys.ata.
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post112187
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
> <sin_ir.txt>Oleg Bolshakov2014-11-05T09:17:55Zpost112187: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112187
Hi Pavel,
here is the sin ir with Fsys.ata.Pekka Tuusjärvi(deleted)2014-10-28T06:57:54Zpost112170: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112170
Hi Pekka,
I'm trying to reproduce your problem...
For more accurate results please attach sin ir output for your
configuration with Fsys.ata.
Regards,
Pavel
24.10.2014 17:50, Pavel Kozlov:
> Thanks for info.
> You have a configuration where Net, AHCI and Dev.ser share one
> interrupt line.
> As an experiment try to run the Dev.ser driver before the Fsys.ahci
> (include and run Dev and Dev.ser from your OS image).
>
> I'll try to reproduce this issue too.
>
> Regards,
> Pavel
>
>
> 24.10.2014 16:45, Pekka Tuusjärvi:
>> Hi Pavel,
>>
>> here is the pci.txt.
>>
>>
>>
>>> Hi Pekka,
>>>
>>> If the MOXA PCI serial card and the AHCI SATA controller share one
>>> interrupt line it is possible that the Dev.ser driver loops forever in
>>> the interrupt handler. I've faced such problem once but with very old
>>> Dev.ser driver.
>>> Please attach show_pci -v and sin ar, sin ver, sin ir output.
>>>
>>> Regards,
>>> Pavel
>>>
>>> 23.10.2014 13:28, Pekka Tuusjärvi:
>>>> Hi,
>>>>
>>>> im trying to use MOXA PCI serial card with Fsys.ahci. I have tried
>>>> different
>>> MOXA PCI products but anyone hasnt worked. After I rebuild the OS
>>> image with
>>> Fsys.ahci the Dev.ser command frozens my PC. Although if I return to
>>> normal
>>> Fsys.ata the PCI-card works normally. Also everything else works
>>> perfectly
>>> with Fsys.ahci.
>>>> The performance of Fsys.ata is so lame that I need to get this
>>>> work. Any
>>> ideas?
>>>>
>>>>
>>>> _______________________________________________
>>>>
>>>> QNX4 Community Support
>>>> http://community.qnx.com/sf/go/post112125
>>>> To cancel your subscription to this discussion, please e-mail
>>>> qnx4-community
>>> -unsubscribe@community.qnx.com
>>
>>
>>
>>
>>
>> _______________________________________________
>>
>> QNX4 Community Support
>> http://community.qnx.com/sf/go/post112143
>> To cancel your subscription to this discussion, please e-mail
>> qnx4-community-unsubscribe@community.qnx.com
>Pavel Kozlov(deleted)2014-10-27T12:47:38Zpost112147: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112147
Thanks for info.
You have a configuration where Net, AHCI and Dev.ser share one interrupt
line.
As an experiment try to run the Dev.ser driver before the Fsys.ahci
(include and run Dev and Dev.ser from your OS image).
I'll try to reproduce this issue too.
Regards,
Pavel
24.10.2014 16:45, Pekka Tuusjärvi:
> Hi Pavel,
>
> here is the pci.txt.
>
>
>
>> Hi Pekka,
>>
>> If the MOXA PCI serial card and the AHCI SATA controller share one
>> interrupt line it is possible that the Dev.ser driver loops forever in
>> the interrupt handler. I've faced such problem once but with very old
>> Dev.ser driver.
>> Please attach show_pci -v and sin ar, sin ver, sin ir output.
>>
>> Regards,
>> Pavel
>>
>> 23.10.2014 13:28, Pekka Tuusjärvi:
>>> Hi,
>>>
>>> im trying to use MOXA PCI serial card with Fsys.ahci. I have tried different
>> MOXA PCI products but anyone hasnt worked. After I rebuild the OS image with
>> Fsys.ahci the Dev.ser command frozens my PC. Although if I return to normal
>> Fsys.ata the PCI-card works normally. Also everything else works perfectly
>> with Fsys.ahci.
>>> The performance of Fsys.ata is so lame that I need to get this work. Any
>> ideas?
>>>
>>>
>>> _______________________________________________
>>>
>>> QNX4 Community Support
>>> http://community.qnx.com/sf/go/post112125
>>> To cancel your subscription to this discussion, please e-mail qnx4-community
>> -unsubscribe@community.qnx.com
>
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post112143
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comPavel Kozlov(deleted)2014-10-24T13:50:58Zpost112146: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112146
And finally sin ver.Pekka Tuusjärvi(deleted)2014-10-24T12:47:52Zpost112145: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112145
Here is the sin ir.Pekka Tuusjärvi(deleted)2014-10-24T12:47:38Zpost112144: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112144
Here is the sin ar.Pekka Tuusjärvi(deleted)2014-10-24T12:46:46Zpost112143: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112143
Hi Pavel,
here is the pci.txt.
> Hi Pekka,
>
> If the MOXA PCI serial card and the AHCI SATA controller share one
> interrupt line it is possible that the Dev.ser driver loops forever in
> the interrupt handler. I've faced such problem once but with very old
> Dev.ser driver.
> Please attach show_pci -v and sin ar, sin ver, sin ir output.
>
> Regards,
> Pavel
>
> 23.10.2014 13:28, Pekka Tuusjärvi:
> > Hi,
> >
> > im trying to use MOXA PCI serial card with Fsys.ahci. I have tried different
> MOXA PCI products but anyone hasnt worked. After I rebuild the OS image with
> Fsys.ahci the Dev.ser command frozens my PC. Although if I return to normal
> Fsys.ata the PCI-card works normally. Also everything else works perfectly
> with Fsys.ahci.
> >
> > The performance of Fsys.ata is so lame that I need to get this work. Any
> ideas?
> >
> >
> >
> > _______________________________________________
> >
> > QNX4 Community Support
> > http://community.qnx.com/sf/go/post112125
> > To cancel your subscription to this discussion, please e-mail qnx4-community
> -unsubscribe@community.qnx.com
> >
>Pekka Tuusjärvi(deleted)2014-10-24T12:45:58Zpost112141: Re: Fsys.ahci
http://community.qnx.com/sf/go/post112141
Hi Pekka,
If the MOXA PCI serial card and the AHCI SATA controller share one
interrupt line it is possible that the Dev.ser driver loops forever in
the interrupt handler. I've faced such problem once but with very old
Dev.ser driver.
Please attach show_pci -v and sin ar, sin ver, sin ir output.
Regards,
Pavel
23.10.2014 13:28, Pekka Tuusjärvi:
> Hi,
>
> im trying to use MOXA PCI serial card with Fsys.ahci. I have tried different MOXA PCI products but anyone hasnt worked. After I rebuild the OS image with Fsys.ahci the Dev.ser command frozens my PC. Although if I return to normal Fsys.ata the PCI-card works normally. Also everything else works perfectly with Fsys.ahci.
>
> The performance of Fsys.ata is so lame that I need to get this work. Any ideas?
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post112125
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
>Pavel Kozlov(deleted)2014-10-24T12:22:57Zpost112125: Fsys.ahci
http://community.qnx.com/sf/go/post112125
Hi,
im trying to use MOXA PCI serial card with Fsys.ahci. I have tried different MOXA PCI products but anyone hasnt worked. After I rebuild the OS image with Fsys.ahci the Dev.ser command frozens my PC. Although if I return to normal Fsys.ata the PCI-card works normally. Also everything else works perfectly with Fsys.ahci.
The performance of Fsys.ata is so lame that I need to get this work. Any ideas?Pekka Tuusjärvi(deleted)2014-10-23T09:28:33Zpost111691: Re: QNX4 USB Boot...
http://community.qnx.com/sf/go/post111691
Thanks Oleg...Victor Gamboa2014-09-10T16:36:10Zpost111685: Re: QNX4 USB Boot...
http://community.qnx.com/sf/go/post111685
Hi Victor,
You don't have to install TCP/IP on the USB flash. You can install TCP/IP later when you'll need it.
Respectfully,
Oleg
09 сент. 2014 г., в 20:11:30, Victor Gamboa <community-noreply@qnx.com> написал:
> I need to install QNX4 on a new machine but it has the PCI BIOS issue, so I read that I have to install qnx on a USB flash, update the Proc32 in the USB flash, and after that use the flash to install qnx on the machine with the pci issue.
> Do I need to install tcpip on the usb flash ?
> Thanks for the help....
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post111681
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2014-09-10T10:30:50Zpost111681: QNX4 USB Boot...
http://community.qnx.com/sf/go/post111681
I need to install QNX4 on a new machine but it has the PCI BIOS issue, so I read that I have to install qnx on a USB flash, update the Proc32 in the USB flash, and after that use the flash to install qnx on the machine with the pci issue.
Do I need to install tcpip on the usb flash ?
Thanks for the help....Victor Gamboa2014-09-09T16:11:30Zpost111680: Re: Network Problem...
http://community.qnx.com/sf/go/post111680
I used another motherboard and the network work fine, probably it was a hardware issue. Thank you all guys for your help. Now I am going to make an USB boot to install QNX on a new machine with the Incompatible PCI Bios.
Thanks again for all the help. VictorVictor Gamboa2014-09-09T14:36:54Zpost111674: Re: Network Problem...
http://community.qnx.com/sf/go/post111674
Hi Victor,
Send me show_pci -vvv output. Can you change interrupt of the ethernet card?
Also try to execute the following nettest.sh script:
---
#!/bin/sh
set +x
slay -f inetd Tcpip Net.rtl8169 Net
sleep 1
slay -f inetd Tcpip Net.rtl8169 Net
Net &
sleep 1
Net.rtl8169 -vvvvvvvvvv &
sleep 1
Tcpip qnx
sleep 1
ifconfig en1 192.168.1.50 up
sleep 1
ping -c3 192.168.1.12
---
Send me output of this script.
Respectfully,
Oleg
06 сент. 2014 г., в 3:05:51, Victor Gamboa <community-noreply@qnx.com> написал:
> Oleg, I attach the file with the outputs from the working and problem machine. Thanks for the help...
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post111666
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
> <at1.txt>Oleg Bolshakov2014-09-08T13:20:59Zpost111667: RE: Network Problem...
http://community.qnx.com/sf/go/post111667
Media rate is 0 and no packet are received, looks like a hardware issue or there is a problem with interrupt 3 ( that`s a strange interrupt has it is often used by serial port )
-----Message d'origine-----
De : Victor Gamboa [mailto:community-noreply@qnx.com]
Envoyé : 5 septembre 2014 19:06
À : qnx4-community
Objet : Re: Network Problem...
Oleg, I attach the file with the outputs from the working and problem machine. Thanks for the help...
_______________________________________________
QNX4 Community Support
http://community.qnx.com/sf/go/post111666
To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comMario Charest2014-09-06T00:06:55Zpost111666: Re: Network Problem...
http://community.qnx.com/sf/go/post111666
Oleg, I attach the file with the outputs from the working and problem machine. Thanks for the help...Victor Gamboa2014-09-05T23:05:51Zpost111664: Re: Network Problem...
http://community.qnx.com/sf/go/post111664
Victor,
Can you send me output following commands (from both working and problem QNX4 machines)?
netmap
netinfo -l
Also check that you set different node ID on both machines.
Respectfully,
Oleg
05 сент. 2014 г., в 21:40, Victor Gamboa <community-noreply@qnx.com> написал:
> The arp -a output on the qnx machine with problems is:
>
> node1 (192.168.1.50) at 00:14:d1:25:13:6a permanent
>
> I don´t know if this could say something.
>
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post111663
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.comOleg Bolshakov2014-09-05T17:53:53Zpost111663: Re: Network Problem...
http://community.qnx.com/sf/go/post111663
The arp -a output on the qnx machine with problems is:
node1 (192.168.1.50) at 00:14:d1:25:13:6a permanent
I don´t know if this could say something.Victor Gamboa2014-09-05T17:40:26Zpost111662: Re: Network Problem...
http://community.qnx.com/sf/go/post111662
Yes I am pinging from a qnx machine to anoter qnx machine. If I tried to telnet (from a telnet client on a windows machine) to the qnx machine with problems, I can´t access. If I telnet to the other working qnx machine I don´t have problems. And with arp -a on the destination machine I can´t see the qnx machine where i was pinging.Victor Gamboa2014-09-05T17:36:39Zpost111661: Re: Network Problem...
http://community.qnx.com/sf/go/post111661
Are you pinging from one QNX4 machine to another QNX4 machine? If so, does
the destination machine have the correct MAC addresses in its netmap file?
If you run Œarp -a¹ on the destination machine, do you see the MAC address
of the machine from which you are pinging?
On 2014/9/5, 1:09 PM, "Victor Gamboa" <community-noreply@qnx.com> wrote:
>Hi Hugh ! Thanks for the help....
>I update the /etc/config/netmap with the MAC Address of the Card (it
>wasn´t equal) but still can´t ping another machine. I disabled the
>network adapter on BIOS and I added a network card on a pci slot, I
>checked the MAC Adress of the new card on /etc/config/netmap, but it
>still don´t work.
>What can I do ?
>
>
>
>_______________________________________________
>
>QNX4 Community Support
>http://community.qnx.com/sf/go/post111660
>To cancel your subscription to this discussion, please e-mail
>qnx4-community-unsubscribe@community.qnx.comHugh Brown2014-09-05T17:15:54Zpost111660: Re: Network Problem...
http://community.qnx.com/sf/go/post111660
Hi Hugh ! Thanks for the help....
I update the /etc/config/netmap with the MAC Address of the Card (it wasn´t equal) but still can´t ping another machine. I disabled the network adapter on BIOS and I added a network card on a pci slot, I checked the MAC Adress of the new card on /etc/config/netmap, but it still don´t work.
What can I do ?Victor Gamboa2014-09-05T17:09:29Zpost111659: Re: Network Problem...
http://community.qnx.com/sf/go/post111659
Does the MAC address in your /etc/config/netmap file match the MAC address
of your RTL 8169 adapter? If not, then edit the /etc/config/netmap file
and correct the MAC address. Then reboot your machine.
On 2014/9/5, 9:40 AM, "Victor Gamboa" <community-noreply@qnx.com> wrote:
>Oleg I put the Net.rtl8169 without arguments on the /etc/config/sysinit.1
>file, reset the machine but I still can´t ping another machine on the
>local network. Any suggestions ?
>
>
>
>_______________________________________________
>
>QNX4 Community Support
>http://community.qnx.com/sf/go/post111658
>To cancel your subscription to this discussion, please e-mail
>qnx4-community-unsubscribe@community.qnx.comHugh Brown2014-09-05T16:46:44Zpost111658: Re: Network Problem...
http://community.qnx.com/sf/go/post111658
Oleg I put the Net.rtl8169 without arguments on the /etc/config/sysinit.1 file, reset the machine but I still can´t ping another machine on the local network. Any suggestions ?Victor Gamboa2014-09-05T13:40:56Zpost111654: Re: Network Problem...
http://community.qnx.com/sf/go/post111654
Hi Victor,
Try to start Net.rtl8169 network driver without arguments. To do this edit sysinit and restart PC.
> Well I can´t make multiple attachments, so I will reply several times for each otuput....
You can store all diagnostics files to one archive and attach it.
Respectfully,
Oleg
05 сент. 2014 г., в 2:00:48, Victor Gamboa <community-noreply@qnx.com> написал:
> sin ver
>
>
>
> _______________________________________________
>
> QNX4 Community Support
> http://community.qnx.com/sf/go/post111650
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
> <sinver.txt>Oleg Bolshakov2014-09-05T08:36:26Zpost111650: Re: Network Problem...
http://community.qnx.com/sf/go/post111650
sin verVictor Gamboa2014-09-04T22:00:48Zpost111649: Re: Network Problem...
http://community.qnx.com/sf/go/post111649
sin tiVictor Gamboa2014-09-04T22:00:38Zpost111648: Re: Network Problem...
http://community.qnx.com/sf/go/post111648
sin ir...Victor Gamboa2014-09-04T22:00:37Zpost111647: Re: Network Problem...
http://community.qnx.com/sf/go/post111647
sin irVictor Gamboa2014-09-04T22:00:13Zpost111646: Re: Network Problem...
http://community.qnx.com/sf/go/post111646
sin inVictor Gamboa2014-09-04T21:59:59Zpost111644: Re: Network Problem...
http://community.qnx.com/sf/go/post111644
ping...Victor Gamboa2014-09-04T21:59:57Zpost111645: Re: Network Problem...
http://community.qnx.com/sf/go/post111645
sin arVictor Gamboa2014-09-04T21:59:54Zpost111643: Re: Network Problem...
http://community.qnx.com/sf/go/post111643
netstat..Victor Gamboa2014-09-04T21:59:29Zpost111642: Re: Network Problem...
http://community.qnx.com/sf/go/post111642
licinfo...Victor Gamboa2014-09-04T21:58:59Zpost111641: Re: Network Problem...
http://community.qnx.com/sf/go/post111641
Oleg I attach the outputs on txtVictor Gamboa2014-09-04T21:58:55Zpost111639: Re: Network Problem...
http://community.qnx.com/sf/go/post111639
And the last one...Victor Gamboa2014-09-04T15:16:46Zpost111638: Re: Network Problem...
http://community.qnx.com/sf/go/post111638
Output 8Victor Gamboa2014-09-04T15:16:07Z