Project Home
Project Home		 Source Code
Source Code		 Documents
Documents		 Wiki
Wiki		 Discussion Forums
Discussions		 Project Information
Project Info
Core Development Tools/Discussion/General/QNX 6.4 Evaluation /List of Posts
Forum Topic - QNX 6.4 Evaluation : (7 Items)
   
Update
Andrew Page
03/10/2009 2:31 PM
post24059
QNX 6.4 Evaluation   
I downloaded the subject (we are definitely considering purchasing for an embedded mission computer in a small UAV), 
added a couple of standard source files etc. Then I added a couple of serial classes to handle RS-232 packets; problem 
is that they do not seem to have been added to my project and hence are not part of the compilation. Is this an issue 
with just the eval version or do I need to do something special to get them to compile in the project?

Thanks!!
Andy
Colin Burgess(deleted)
03/10/2009 2:34 PM
post24060
Re: QNX 6.4 Evaluation   
The evaluation isn't crippled in any way - are you using the IDE?  You might want to ask in the IDE forum too.

If you are using a QNX makefile then your source files are compiled automatically, unless they are in a non standard
path.  You can add extra dirs with EXTRA_SRCVPATH

Colin

Andrew Page wrote:
> I downloaded the subject (we are definitely considering purchasing for an embedded mission computer in a small UAV), 
added a couple of standard source files etc. Then I added a couple of serial classes to handle RS-232 packets; problem 
is that they do not seem to have been added to my project and hence are not part of the compilation. Is this an issue 
with just the eval version or do I need to do something special to get them to compile in the project?
> 
> Thanks!!
> Andy
> 
> _______________________________________________
> General
> http://community.qnx.com/sf/go/post24059
> 

-- 
cburgess@qnx.com
Andrew Page
03/10/2009 3:06 PM
post24064
RE: QNX 6.4 Evaluation   
Great! Thanks for the assistance

Andy 

-----Original Message-----
From: Colin Burgess [mailto:community-noreply@qnx.com] 
Sent: Tuesday, March 10, 2009 11:34 AM
To: general-toolchain
Subject: Re: QNX 6.4 Evaluation

The evaluation isn't crippled in any way - are you using the IDE?  You
might want to ask in the IDE forum too.

If you are using a QNX makefile then your source files are compiled
automatically, unless they are in a non standard path.  You can add
extra dirs with EXTRA_SRCVPATH

Colin

Andrew Page wrote:
> I downloaded the subject (we are definitely considering purchasing for
an embedded mission computer in a small UAV), added a couple of standard
source files etc. Then I added a couple of serial classes to handle
RS-232 packets; problem is that they do not seem to have been added to
my project and hence are not part of the compilation. Is this an issue
with just the eval version or do I need to do something special to get
them to compile in the project?
> 
> Thanks!!
> Andy
> 
> _______________________________________________
> General
> http://community.qnx.com/sf/go/post24059
> 

--
cburgess@qnx.com

_______________________________________________
General
http://community.qnx.com/sf/go/post24060
Alex Chapiro
03/10/2009 3:00 PM
post24063
Re: QNX 6.4 Evaluation   
It's important to understand what were your actions.
1)Is it IDE project?
If yes:
     - what type of project did you use?
     - how did you add your new classes?
     - how did you understand that these new classses were not added? 
Can you send your IDE console log ?

Regards,

Alex


On 10/03/2009 2:31 PM, Andrew Page wrote:
> I downloaded the subject (we are definitely considering purchasing for an embedded mission computer in a small UAV), 
added a couple of standard source files etc. Then I added a couple of serial classes to handle RS-232 packets; problem 
is that they do not seem to have been added to my project and hence are not part of the compilation. Is this an issue 
with just the eval version or do I need to do something special to get them to compile in the project?
>
> Thanks!!
> Andy
>
> _______________________________________________
> General
> http://community.qnx.com/sf/go/post24059
>
>
Andrew Page
03/10/2009 3:17 PM
post24066
RE: QNX 6.4 Evaluation   
As usual this was an operator error; which I have encountered numerous
times over the days that I have had the eval copy;-)
It is an IDE project, 
I added the classes via project explorer,
I knew they were not in the original config I set up due to an
intentional bug within 

I think (key work there) that the issue was in the toolchain config I
set up, I now have the compiler/assembler/linker/archiver all set to QCC
and am using the CDT Internal Builder; still not sure whether that is
the correct configuration or not (or, quite frankly, if that was even
the problem) but the new classes are part of the compilation because the
problem child definitely blew up and halted the compile in its tracks.

Boy, there is a lot to this 

-----Original Message-----
From: Alex Chapiro [mailto:community-noreply@qnx.com] 
Sent: Tuesday, March 10, 2009 12:01 PM
To: general-toolchain
Subject: Re: QNX 6.4 Evaluation

It's important to understand what were your actions.
1)Is it IDE project?
If yes:
     - what type of project did you use?
     - how did you add your new classes?
     - how did you understand that these new classses were not added? 
Can you send your IDE console log ?

Regards,

Alex


On 10/03/2009 2:31 PM, Andrew Page wrote:
> I downloaded the subject (we are definitely considering purchasing for
an embedded mission computer in a small UAV), added a couple of standard
source files etc. Then I added a couple of serial classes to handle
RS-232 packets; problem is that they do not seem to have been added to
my project and hence are not part of the compilation. Is this an issue
with just the eval version or do I need to do something special to get
them to compile in the project?
>
> Thanks!!
> Andy
>
> _______________________________________________
> General
> http://community.qnx.com/sf/go/post24059
>
>    


_______________________________________________
General
http://community.qnx.com/sf/go/post24063
Alex Chapiro
03/10/2009 4:00 PM
post24076
Re: QNX 6.4 Evaluation   
OK,

Seems to me it was a managed make project. In this case you either add 
new files into the same project directory (or its sub-directories) - 
then all should be done automatically, or somewhere else. In the last 
case you should  register new location in C/C++ General -> Paths & 
Symbols -> Source Location.

Alex

On 10/03/2009 3:17 PM, Andrew Page wrote:
> As usual this was an operator error; which I have encountered numerous
> times over the days that I have had the eval copy;-)
> It is an IDE project,
> I added the classes via project explorer,
> I knew they were not in the original config I set up due to an
> intentional bug within
>
> I think (key work there) that the issue was in the toolchain config I
> set up, I now have the compiler/assembler/linker/archiver all set to QCC
> and am using the CDT Internal Builder; still not sure whether that is
> the correct configuration or not (or, quite frankly, if that was even
> the problem) but the new classes are part of the compilation because the
> problem child definitely blew up and halted the compile in its tracks.
>
> Boy, there is a lot to this
>
> -----Original Message-----
> From: Alex Chapiro [mailto:community-noreply@qnx.com]
> Sent: Tuesday, March 10, 2009 12:01 PM
> To: general-toolchain
> Subject: Re: QNX 6.4 Evaluation
>
> It's important to understand what were your actions.
> 1)Is it IDE project?
> If yes:
>       - what type of project did you use?
>       - how did you add your new classes?
>       - how did you understand that these new classses were not added?
> Can you send your IDE console log ?
>
> Regards,
>
> Alex
>
>
> On 10/03/2009 2:31 PM, Andrew Page wrote:
>    
>> I downloaded the subject (we are definitely considering purchasing for
>>      
> an embedded mission computer in a small UAV), added a couple of standard
> source files etc. Then I added a couple of serial classes to handle
> RS-232 packets; problem is that they do not seem to have been added to
> my project and hence are not part of the compilation. Is this an issue
> with just the eval version or do I need to do something special to get
> them to compile in the project?
>    
>> Thanks!!
>> Andy
>>
>> _______________________________________________
>> General
>> http://community.qnx.com/sf/go/post24059
>>
>>
>>      
> _______________________________________________
> General
> http://community.qnx.com/sf/go/post24063
>
>
> _______________________________________________
> General
> http://community.qnx.com/sf/go/post24066
>
>
Andrew Page
03/10/2009 5:55 PM
post24087
RE: QNX 6.4 Evaluation   
Hey, you're right I did "convert" it to a managed project; but its not
clear (yet) why I did that. Good news is that a couple of your folks
will be here tomorrow to give a demo and answer questions; this will be
one of them.

Thanks Alex

Andy

-----Original Message-----
From: Alex Chapiro [mailto:community-noreply@qnx.com] 
Sent: Tuesday, March 10, 2009 1:01 PM
To: general-toolchain
Subject: Re: QNX 6.4 Evaluation

OK,

Seems to me it was a managed make project. In this case you either add
new files into the same project directory (or its sub-directories) -
then all should be done automatically, or somewhere else. In the last
case you should  register new location in C/C++ General -> Paths &
Symbols -> Source Location.

Alex

On 10/03/2009 3:17 PM, Andrew Page wrote:
> As usual this was an operator error; which I have encountered numerous

> times over the days that I have had the eval copy;-) It is an IDE 
> project, I added the classes via project explorer, I knew they were 
> not in the original config I set up due to an intentional bug within
>
> I think (key work there) that the issue was in the toolchain config I 
> set up, I now have the compiler/assembler/linker/archiver all set to 
> QCC and am using the CDT Internal Builder; still not sure whether that

> is the correct configuration or not (or, quite frankly, if that was 
> even the problem) but the new classes are part of the compilation 
> because the problem child definitely blew up and halted the compile in
its tracks.
>
> Boy, there is a lot to this
>
> -----Original Message-----
> From: Alex Chapiro [mailto:community-noreply@qnx.com]
> Sent: Tuesday, March 10, 2009 12:01 PM
> To: general-toolchain
> Subject: Re: QNX 6.4 Evaluation
>
> It's important to understand what were your actions.
> 1)Is it IDE project?
> If yes:
>       - what type of project did you use?
>       - how did you add your new classes?
>       - how did you understand that these new classses were not added?
> Can you send your IDE console log ?
>
> Regards,
>
> Alex
>
>
> On 10/03/2009 2:31 PM, Andrew Page wrote:
>    
>> I downloaded the subject (we are definitely considering purchasing 
>> for
>>      
> an embedded mission computer in a small UAV), added a couple of 
> standard source files etc. Then I added a couple of serial classes to 
> handle
> RS-232 packets; problem is that they do not seem to have been added to

> my project and hence are not part of the compilation. Is this an issue

> with just the eval version or do I need to do something special to get

> them to compile in the project?
>    
>> Thanks!!
>> Andy
>>
>> _______________________________________________
>> General
>> http://community.qnx.com/sf/go/post24059
>>
>>
>>      
> _______________________________________________
> General
> http://community.qnx.com/sf/go/post24063
>
>
> _______________________________________________
> General
> http://community.qnx.com/sf/go/post24066
>
>    


_______________________________________________
General
http://community.qnx.com/sf/go/post24076

Return


  A subsidiary of BlackBerry             All content ©2004-2013, QNX Software Systems