Project Home
Project Home		 Wiki
Wiki		 Discussion Forums
Discussions		 Project Information
Project Info
QNX RTOS v4 [EOL]/Discussion/General/Fsys.atapi on Panasonic Touchbook CF-30/List of Posts
Forum Topic - Fsys.atapi on Panasonic Touchbook CF-30: (4 Items)
   
Update
Eric Milne
11/19/2009 1:58 PM
post42265
Fsys.atapi on Panasonic Touchbook CF-30   
I'm trying to install QNX 4.25 onto a Panasonic Toughbook CF-30 with the Intel ICH9M-E/M sata chipset.  I'm using the 
latest installation CD from November 2009 and it is unable to locate the hard drive.  Is there a trick to getting the 
installation to see the drive?
Oleg Bolshakov
11/23/2009 12:33 PM
post42392
Re: Fsys.atapi on Panasonic Touchbook CF-30   
Hi Eric,

There is a trick to start the Fsys.atapi manually while you installing:

1. Set "Run installation in diagnostic mode. / F12" check box on the first 
QNX Installer 2009 screen. Then press Next.

2. Unset "EIDE Disk Controller" on the "Select Hardware to Auto-detect" 
screen and press Next.

3. When "Auto-detecting Hardware..." is done use "Add" button to run the 
Fsys.atapi driver. In opened window choose category "Disk Controllers" and 
hardware driver "EIDE Disk Controller". Enter in the Command Line:

Fsys.atapi atapi ioport=0x1f0,irq=14 atapi ioport=0x170,irq=15

And press OK.

The ioport=0x1f0,irq=14 and ioport=0x170,irq=15 are generic parameters. 
You can get specific I/O ports and IRQs from the PCI configurations.

Next thread may be helpful: http://community.qnx.com/sf/go/post40388

-- 
Respectfully,
Oleg

> I'm trying to install QNX 4.25 onto a Panasonic Toughbook CF-30 with
>  the Intel ICH9M-E/M sata chipset.  I'm using the latest installation
>  CD from November 2009 and it is unable to locate the hard drive.  Is
>  there a trick to getting the installation to see the drive?
> 
> 
> 
> _______________________________________________
> 
> General
> http://community.qnx.com/sf/go/post42265
>
Tristan Crees
07/23/2010 7:09 PM
post60496
Re: Fsys.atapi on Panasonic Touchbook CF-30   
23-July-2010

I have the same problem.  Panasonic CF-30 toughbook.  I get to the hardware scan and cannot get the HDD recognised.  I 
tried running Fsys.atapi manually with this command:
Fsys.atapi atapi ioport=0xe150,ira=10 atapi ioport=0xc040,irq=15

But neither the CD nor the HDD were found.

If I run Fsys.atapi with no arguments, only the CD is found.

I tried looking in the BIOS, but there are no options associated with the SATA controller.

Has anyone got a resolution to this problem?

Please email me direct: tcrees@ise.bc.ca

Thanks, Tristan.
Oleg Bolshakov
08/02/2010 6:37 AM
post61330
Re: Fsys.atapi on Panasonic Touchbook CF-30   
Hi Tristan,

Sorry for delay with answer. Please post here show_pci -vvv output.

CC to tcrees@ise.bc.ca . Also you can subscribe to receive new answers in 
any topic on the Foundry27.

-- 
Respectfully,
Oleg

> 23-July-2010
> 
> I have the same problem.  Panasonic CF-30 toughbook.  I get to the
> hardware scan and cannot get the HDD recognised.  I tried running
> Fsys.atapi manually with this command: Fsys.atapi atapi
> ioport=0xe150,ira=10 atapi ioport=0xc040,irq=15
> 
> But neither the CD nor the HDD were found.
> 
> If I run Fsys.atapi with no arguments, only the CD is found.
> 
> I tried looking in the BIOS, but there are no options associated with
> the SATA controller.
> 
> Has anyone got a resolution to this problem?
> 
> Please email me direct: tcrees@ise.bc.ca
> 
> Thanks, Tristan.
> 
> 
> 
> _______________________________________________
> 
> General
> http://community.qnx.com/sf/go/post60496

Return


  A subsidiary of BlackBerry             All content ©2004-2013, QNX Software Systems