Driver attached.




On 2013-09-23 8:44 AM, "Zi Yang Pang" <community-noreply@qnx.com> wrote:

>Hi,
>
>X86 please. Thank you very much!
>
>Ziyang
>
>-----Original Message-----
>From: Hugh Brown [mailto:community-noreply@qnx.com]
>Sent: Monday, September 23, 2013 8:43 AM
>To: general-networking@community.qnx.com
>Subject: Re: Networking probem with QNX 6.5 with Athena II SBC (NS83815
>Ethernet adapters)
>
>For some reason that driver wasn't shipped with 6.5.0. I can send you a
>version if you like. Which platform - x86,armŠ?
>
>
>
>
>On 2013-09-20 5:49 PM, "Zi Yang Pang" <community-noreply@qnx.com> wrote:
>
>>Hi,
>>
>>Are there drivers for NS83815 Ethernet adapters in QNX6.5? I know that
>>the latest supported version is 6.3.2 according to QNX hardware database.
>>
>>Will I be able use devn-ns83815.so found in previous versions of QNX
>>SDP in v6.5?
>>
>>
>>
>>
>>_______________________________________________
>>
>>General
>>http://community.qnx.com/sf/go/post105294
>>To cancel your subscription to this discussion, please e-mail
>>general-networking-unsubscribe@community.qnx.com
>
>
>
>
>
>_______________________________________________
>
>General
>http://community.qnx.com/sf/go/post105312
>To cancel your subscription to this discussion, please e-mail
>general-networking-unsubscribe@community.qnx.com
>
>
>
>
>
>_______________________________________________
>
>General
>http://community.qnx.com/sf/go/post105313
>To cancel your subscription to this discussion, please e-mail
>general-networking-unsubscribe@community.qnx.com

Please can you start "io-pkt-v4-hc -dns83815 verbose=3" and post the slog
info output?

Thanks.



On 2013-09-23 10:56 AM, "ziyang" <community-noreply@qnx.com> wrote:

>Hi Hughs,
>
>when I loaded the driver using io-pkt-v4-hc -dns83815, my nicinfo shows
>that en0: ns83815: DP83815 Ethernet controller but current operation
>rate is 0kb/s and the active PHY address is 0. How can I solve this?
>
>Thanks
>
>Ziyang
>
>
>On 09/23/2013 08:43 AM, Hugh Brown wrote:
>> For some reason that driver wasn't shipped with 6.5.0. I can send you a
>> version if you like. Which platform - x86,armŠ?
>>
>>
>>
>>
>> On 2013-09-20 5:49 PM, "Zi Yang Pang" <community-noreply@qnx.com> wrote:
>>
>>> Hi,
>>>
>>> Are there drivers for NS83815 Ethernet adapters in QNX6.5? I know that
>>> the latest supported version is 6.3.2 according to QNX hardware
>>>database.
>>>
>>> Will I be able use devn-ns83815.so found in previous versions of QNX
>>>SDP
>>> in v6.5?
>>>
>>>
>>>
>>>
>>> _______________________________________________
>>>
>>> General
>>> http://community.qnx.com/sf/go/post105294
>>> To cancel your subscription to this discussion, please e-mail
>>> general-networking-unsubscribe@community.qnx.com
>>
>>
>>
>>
>> _______________________________________________
>>
>> General
>> http://community.qnx.com/sf/go/post105312
>> To cancel your subscription to this discussion, please e-mail
>>general-networking-unsubscribe@community.qnx.com
>
>
>
>
>
>_______________________________________________
>
>General
>http://community.qnx.com/sf/go/post105322
>To cancel your subscription to this discussion, please e-mail
>general-networking-unsubscribe@community.qnx.com