Hello, Is it possible to have QNET on ethernet without using TCPIP? ( similar to what we had in QNX4 , native networking) Regards Praveen
I just tried running the io-pkt as below slay io-pkt-v4-hc io-pkt-v4-hc -drtl -pqnet & didnot configure IP address. I could get other QNX system listed under /net Hope this is the correct way? Regards Praveen
QNet is started if /etc/system/config/useqnet file is present/readable (may be an empty file). TCPIP driver is always loaded with io-pkt whether you specify -ptcpip or not. It is just up to you if to use it.
Thanks So if i donot configure IP , the qnet is not working with IP? Regards Praveen ----- Original Message ----- From: "Oleh Derevenko" <community-noreply@qnx.com> To: "general-networking" <post90446@community.qnx.com> Sent: Wednesday, December 07, 2011 12:03 AM Subject: Re: QNET without TCPIP? Is it possible > QNet is started if /etc/system/config/useqnet file is present/readable > (may be an empty file). > TCPIP driver is always loaded with io-pkt whether you specify -ptcpip or > not. It is just up to you if to use it. > > > > _______________________________________________ > > General > http://community.qnx.com/sf/go/post90446 > >
-----Message d'origine----- De : Praveen VS [mailto:community-noreply@qnx.com] Envoyé : 6 décembre 2011 23:02 À : general-networking Objet : Re: QNET without TCPIP? Is it possible Thanks So if i donot configure IP , the qnet is not working with IP? Regards Praveen By default QNET is not working with IP even if TCPIP is running. You have to specify special option to get qnet to run over IP. ----- Original Message ----- From: "Oleh Derevenko" <community-noreply@qnx.com> To: "general-networking" <post90446@community.qnx.com> Sent: Wednesday, December 07, 2011 12:03 AM Subject: Re: QNET without TCPIP? Is it possible > QNet is started if /etc/system/config/useqnet file is present/readable > (may be an empty file). > TCPIP driver is always loaded with io-pkt whether you specify -ptcpip or > not. It is just up to you if to use it. > > > > _______________________________________________ > > General > http://community.qnx.com/sf/go/post90446 > > _______________________________________________ General http://community.qnx.com/sf/go/post90459
Thanks for confirmation Regards Praveen ----- Original Message ----- From: "Mario Charest" <community-noreply@qnx.com> To: "general-networking" <post90460@community.qnx.com> Sent: Wednesday, December 07, 2011 9:38 AM Subject: RE: QNET without TCPIP? Is it possible > > > -----Message d'origine----- > De : Praveen VS [mailto:community-noreply@qnx.com] > Envoyé : 6 décembre 2011 23:02 > À : general-networking > Objet : Re: QNET without TCPIP? Is it possible > > Thanks > So if i donot configure IP , the qnet is not working with IP? > Regards > Praveen > > By default QNET is not working with IP even if TCPIP is running. You have > to specify special option to get qnet to run over IP. > > ----- Original Message ----- > From: "Oleh Derevenko" <community-noreply@qnx.com> > To: "general-networking" <post90446@community.qnx.com> > Sent: Wednesday, December 07, 2011 12:03 AM > Subject: Re: QNET without TCPIP? Is it possible > > >> QNet is started if /etc/system/config/useqnet file is present/readable >> (may be an empty file). >> TCPIP driver is always loaded with io-pkt whether you specify -ptcpip or >> not. It is just up to you if to use it. >> >> >> >> _______________________________________________ >> >> General >> http://community.qnx.com/sf/go/post90446 >> >> > > > > > > _______________________________________________ > > General > http://community.qnx.com/sf/go/post90459 > > > > > > _______________________________________________ > > General > http://community.qnx.com/sf/go/post90460 >
