Thank you Hugh, 
I have overcome the Display problem, I seems that there is NO deriver for
this?!
*) I have downloaded and replace the .so file in the /lib/dll but still the
same problem!
When setting the ip address using the gui they are still not being retained?

So I have manually added the "ifconfig en0 192.168.1.2" how do I set the
"dhcp" for the other network interface?

**) Also both of the drives still have the SHIM flag on, is it normal?
Shouldn't it have the tigon3 or something similar!

Many thanks
Amir

P.S -One of the network cards is BCM5754 and I typed it in as BCM5724.

-----Original Message-----
From: Hugh Brown [mailto:community-noreply@qnx.com] 
Sent: Wednesday, 13 May 2009 10:07 PM
To: drivers-networking
Subject: RE: RE: (BCM5721 and BCM5724) NetXtreme Gigabit Ethernet PCI
Express - Device Drive for QNX 6.4

I am not a graphics person, so I will forward your question to a graphics
person. AFAIK the nVidia chips are not supported by QNX. To overcome your
problem, boot from the installation CD and choose the "run from CD" option.
You can then look under /fs to find your disk partition, then "cd
/fs/your_partition/etc/system/config". Then you can do a "> nophoton" and
reboot your machine without the CD. You can then login in text mode.


-----Original Message-----
From: Amir Sadrossadat [mailto:community-noreply@qnx.com]
Sent: Wednesday, May 13, 2009 1:11 AM
To: drivers-networking
Subject: RE: RE: (BCM5721 and BCM5724) NetXtreme Gigabit Ethernet PCI
Express - Device Drive for QNX 6.4

Thank Hugh,

I can't log in to my machine at the moment :( Read the following ...


Another *driver* problem that I have had is the configurator->display drive.
The Driver has been picked up as "vesabios". The HW/Details shows a "nVidia,
Quadro FX 1700, vid= 0x10de did=0x40f index=1", and the QNX hardware site
suggests a "devg-tnt.so" for all nVidia family! Does 6.4 supports this H/W?
I've added a line to the /etc/system/enum/drivers/graphics it now comes with
the "fatal error popup window saying, Load_display_info(): unable to for
"0x10de,0x40f,1" Which I can only "EXIT".
*) I can't log in as super user! So I am kind of stuck! 


I try to log out, and 'Exit to text mode" but it hangs! 

-----Original Message-----
From: Hugh Brown [mailto:community-noreply@qnx.com]
Sent: Tuesday, 12 May 2009 10:03 PM
To: drivers-networking
Subject: RE: RE: (BCM5721 and BCM5724) NetXtreme Gigabit Ethernet PCI
Express - Device Drive for QNX 6.4

The 167a device ID was not in our driver, so that is why you only got en0. I
have attached an experimental driver with that device ID added.
Please try it and let us know if it solves the problem.

Hugh.

-----Original Message-----
From: Amir Sadrossadat [mailto:community-noreply@qnx.com]
Sent: Tuesday, May 12, 2009 3:54 AM
To: drivers-networking
Subject: Re: RE: (BCM5721 and BCM5724) NetXtreme Gigabit Ethernet PCI
Express - Device Drive for QNX 6.4

Thank you Hugh, Andrew, and also Andy from Symmetry.
1)The Vendor ID for both is 14e4h (Broadcom).
2) I did attempt to add following two lines into my /etc/rc.d/rc.local
*) 'slay -fQ io-pkt-v4-hc' and ran 
**) 'io-pkt-v4-hc  -d tigon3 did=0x14e4h vid=0x1659h   -d  tigon3
did=0x0x14e4h, vid=0x167ah
3) When I reboot "ifconfig" shows (en0) and (en1). which is great :)
4) I then use the configuration->network and add in the ip-addresses, and
make it enable, and all is good. I can ping and see my networks.
However, when I restart the machine, It all goes back to only one "en0"
again! My guess is the fact of reloading the driver "in rc.local" clears any
saved setting!! 

Another *driver* problem that I have had is the configurator->display drive.
The Driver has been picked up as "vesabios". The HW/Details shows a "nVidia,
Quadro FX 1700, vid= 0x10de did=0x40f index=1", and the QNX hardware site
suggests a "devg-tnt.so" for all nVidia family! Does 6.4 supports this...