Project Home
Project Home		 Trackers
Trackers		 Documents
Documents		 Wiki
Wiki		 Discussion Forums
Discussions		 Project Information
Project Info
Community/Discussion/QNX4 Community Support (EOL)/Screen on qnx/List of Posts
Forum Topic - Screen on qnx: Page 1 of 2 (14 Items)
   
Update
Will Milner
06/15/2012 3:37 PM
post93702
Screen on qnx   
Is it possible to run a terminal command similar to screen like on linux? I'm trying to connect to a device through a 
serial port and need to start a session, thanks!
Hugh Brown
06/18/2012 8:18 AM
post93723
Re: Screen on qnx   
You can use qtalk to start a serial session and you can use the stty
command to set the baud rate etc.

-- 
Hugh Brown
QNX Software Systems Limited
1001 Farrar Rd.,
Ottawa. ON. K2K 0B3.
Telephone: 613-591-0931







On 12-06-15 3:37 PM, "Will Milner" <community-noreply@qnx.com> wrote:

>Is it possible to run a terminal command similar to screen like on linux?
>I'm trying to connect to a device through a serial port and need to start
>a session, thanks!
>
>
>
>_______________________________________________
>
>QNX4 Community Support
>http://community.qnx.com/sf/go/post93702
>To cancel your subscription to this discussion, please e-mail
>qnx4-community-unsubscribe@community.qnx.com
Will Milner
06/18/2012 12:31 PM
post93733
Re: Screen on qnx   
When I use qtalk I type qtalk /dev/ser1 and it says unable to dial : no dialing entry , and when I try qtalk -m/dev/ser1
 it will pop up with some commadns but I am unable to type any characters to communicate to the device, I configured 
everything with stty before I ran qtalk too, anything I'm missing?  Thanks!
Hugh Brown
06/18/2012 12:52 PM
post93734
Re: Screen on qnx   
If you are connected to a modem, then after you have run "qtalk -m
/dev/ser1", you should then be able to use the modem "at" commands to dial.

-- 
Hugh Brown
QNX Software Systems Limited
1001 Farrar Rd.,
Ottawa. ON. K2K 0B3.
Telephone: 613-591-0931







On 12-06-18 12:31 PM, "Will Milner" <community-noreply@qnx.com> wrote:

>When I use qtalk I type qtalk /dev/ser1 and it says unable to dial : no
>dialing entry , and when I try qtalk -m/dev/ser1 it will pop up with some
>commadns but I am unable to type any characters to communicate to the
>device, I configured everything with stty before I ran qtalk too,
>anything I'm missing?  Thanks!
>
>
>
>_______________________________________________
>
>QNX4 Community Support
>http://community.qnx.com/sf/go/post93733
>To cancel your subscription to this discussion, please e-mail
>qnx4-community-unsubscribe@community.qnx.com
Will Milner
06/18/2012 1:02 PM
post93735
Re: Screen on qnx   
I'm using a null modem cable so I don't think any "at" commands are accessible to me, just a direct link between the 
devices
Hugh Brown
06/18/2012 1:47 PM
post93737
Re: Screen on qnx   
Well if you are running a terminal program on the other machine and you
type characters on the QNX machine, you should see them on the other
machine.

-- 
Hugh Brown
QNX Software Systems Limited
1001 Farrar Rd.,
Ottawa. ON. K2K 0B3.
Telephone: 613-591-0931







On 12-06-18 1:02 PM, "Will Milner" <community-noreply@qnx.com> wrote:

>I'm using a null modem cable so I don't think any "at" commands are
>accessible to me, just a direct link between the devices
>
>
>
>_______________________________________________
>
>QNX4 Community Support
>http://community.qnx.com/sf/go/post93735
>To cancel your subscription to this discussion, please e-mail
>qnx4-community-unsubscribe@community.qnx.com
Will Milner
06/18/2012 1:46 PM
post93738
Re: Screen on qnx   
I seem to have no connection, but if I use utilities like cat and echo I can send and receive but i can't get qtalk to 
emulate a terminal for me, there are no other commands like putty or hyperterminal on qnx that I can try?  Thanks so 
much for your help
Hugh Brown
06/18/2012 2:39 PM
post93740
Re: Screen on qnx   
Well if cat and echo are working, your serial connection must be good. By
default qtalk doesn't echo characters on your QNX terminal, but if the
serial connection is good, you should at least see the characters on the
other terminal. qtalk is the only emulation program under QNX4, but I'm
sure that there are others in the community if you ask around.

-- 
Hugh Brown
QNX Software Systems Limited
1001 Farrar Rd.,
Ottawa. ON. K2K 0B3.
Telephone: 613-591-0931







On 12-06-18 1:46 PM, "Will Milner" <community-noreply@qnx.com> wrote:

>I seem to have no connection, but if I use utilities like cat and echo I
>can send and receive but i can't get qtalk to emulate a terminal for me,
>there are no other commands like putty or hyperterminal on qnx that I can
>try?  Thanks so much for your help
>
>
>
>_______________________________________________
>
>QNX4 Community Support
>http://community.qnx.com/sf/go/post93738
>To cancel your subscription to this discussion, please e-mail
>qnx4-community-unsubscribe@community.qnx.com
Oleg Bolshakov
06/18/2012 2:57 PM
post93741
Re: Screen on qnx   
Hi Will,

To provide remote access to QNX terminal via null-modem cable you should use tinit command.

Respectfully,
Oleg

18.06.2012, в 21:46:57, Will Milner написал(а):

> I seem to have no connection, but if I use utilities like cat and echo I can send and receive but i can't get qtalk to
 emulate a terminal for me, there are no other commands like putty or hyperterminal on qnx that I can try?  Thanks so 
much for your help
> 
> 
> 
> _______________________________________________
> 
> QNX4 Community Support
> http://community.qnx.com/sf/go/post93738
> To cancel your subscription to this discussion, please e-mail qnx4-community-unsubscribe@community.qnx.com
Will Milner
06/19/2012 12:48 PM
post93766
Re: Screen on qnx   
in regards to using tinit when I do tinit -t /dev/ser1 it says missing '=' for macro
12Next

Return


  A subsidiary of BlackBerry             All content ©2004-2013, QNX Software Systems